HP Compaq S1922 User Guide

							
ENWWInstalling the Monitor 5
3. Press the base into the column until it locks in position. 
Figure 3-2   Attaching the Base
4. Lift the monitor to an upright position and place on a flat, stable surface. 
Figure 3-3   Monitor in upright position
 
 
Preparing the monitor for wall-mounting 
1. Check the stability of  the wall-mounting fixture.
  WARNING!  To reduce the risk of personal injury or of damage to the equipment, 
check that the wall-mounting fixture is adequately installed and secured before 
attaching the monitor. Refer to the instruct ions supplied with the wall-mounting fixture 
and check that it is capabl e of supporting the monitor.
2. Disconnect the power cable and any other cables from the monitor.
3. Place the monitor face down on a flat, protected surface.
4. Adjust the stand to a proper angle and remove the screw hidden in the column  cover that fasten the  base to the monitor.
Figure 3-4   Location of screw securing base to monitor 
 
						

							
6 Chapter 3.   Setting Up the MonitorENWW 
 
5. Slide the base away from the bottom of the monitor. 
Figure 3-5   Sliding the base away from the monitor
6. Remove the screws on the back of monitor. 
Figure 3-6   Removing the screws from the back of the monitor
7. Four threaded holes are exposed. These holes are for screws to attach the swing 
arm or other mounting fixture to the back of the monitor. 
8. Follow the instructions included with t he mounting fixture to ensure that the 
monitor is safely attached. The four threaded holes that are on the back of the 
panel are compliant with the VESA standa rd for mounting flat-panel monitors.
9. Attach a swing arm or other mounting fixture.
 
						

							
ENWWConnecting Monitor Cables 7
Connecting Monitor Cables
Connecting the VGA (Analog) Cable or DVI-D (Digital) Cable
Use a VGA video cable or a DVI-D cable to connect your monitor to your computer. To 
use DVI, you must have a DVI-compliant graphic card. Connectors are located on the 
back of the monitor. Be sure the computer and monitor are turned off and unplugged.
1. To connect the VGA cable 
Connect one end of the VGA video cable to the back of the monitor and the other end 
to the VGA video connector on the computer.
2. To connect the DVI-D cable (provided with select models)
Connect one end of the DVI-D video cable to the back of the monitor and the other 
end to the DVI-D video connector on the com puter. You can use this cable only if your 
computer has a DVI compliant graphics card installed. The monitor DVI-D connector 
and cable are included.
Figure 3-7   
Connecting the VGA or a DVI-D cable - connector locations may vary
 
  NOTE:  When using a VGA or DVI signal , you must connect your audio 
separately because a VGA or DVI signal c onverts only video data, not audio data.
Connecting the Audio Cable (Select Models) 
Connect the built-in monitor speakers to th e computer by using the audio cable as 
shown in the following illustration
Figure 3-8 connecting the Audio Cables - connector locations may vary
 
						

							
8 Chapter 3.   Setting Up the MonitorENWW 
 
High-Bandwidth Digital Content Protection (HDCP) 
(Available on Select Models)
Your monitor supports HDCP and can receive high-definition content. High-definition 
content is available in many sources, such as Blue-ray Disc devices or HDTV air or 
cable broadcasts. If you do not have an HDCP-enabled monitor, you will see a blank 
screen or a lower resolution picture when  playing high-definition protected content. 
Your computer graphics card and monitor must both support HDCP to display 
protected content.
Connecting the Power Cable
1. Follow all Electrical and Power Warnings
 WARNING!  To reduce the risk of electric shock or damage to your equipment: Do 
not disable the power cord grounding plug. The grounding plug is an important safety 
feature.
Plug the power cord into a grounded (earthed) electrical outlet.
Be sure that the grounded power outlet y ou plug the power cord into is easily 
accessible to the operator and located as close to the equipment as possible. A power 
cord should be routed so that it is not lik ely to be walked on or pinched by items that 
are placed upon it or against it.
Do not place anything on power cords or cables. Arrange them so that no one may 
accidentally step on or trip over them. Do not pull on a cord or cable.
SeeTechnical Specification (Appendix B) for additional information.
Figure 3-9 Connecting the power cable
2. Connect one end of the power cable to the monitor and the other end to a  grounded electrical outlet.
  WARNING!  To prevent injury from electrical shock, you should do one of the 
following if a properly grounded electrical ou tlet is not available: (1) You should use an 
electrical outlet adapter th at provides proper grounding. (2) You should have a 
properly grounded electrical outlet installed.
 
						

							
ENWWAdjusting the Tilt 9
Adjusting the Tilt
For optimal viewing, adjust the screen tilt to your own preference, as follows:
1. Face the front of the monitor and hold the base so that you do not topple the  monitor while changing the tilt.
2. Adjust the tilt by moving the top edge of  the monitor either toward or away from 
you, without touching the screen.
Figure 3-10 Tilt adjustment
 
						

							
ENWWCD Software and Utilities 10
4. Operating the Monitor
CD Software and Utilities
The CD that is included with this monitor contains drivers and software that you can 
install on your computer.
Installing Drivers
If you determine that you need to update the dr ivers, you can install the monitor driver 
INF and ICM files from the CD, or  download them from the Internet.
Installing the monitor driver software from the CD
To install the monitor driver software from the CD:
1. Insert the CD in your computer CD drive. The CD menu appears.
2. Select the language.
3. Click  Install Monitor Driver Software  .
4. Follow the on-screen instructions.
5. Ensure that the proper resolutions and refresh rates appear in the Display Control  Panel settings.
Refer to the Windows
®  operating system documentation for more information.
  NOTE:  You might need to install the digitally signed monitor drivers (INF or ICM 
files) manually from the CD, in case of  an installation error. Refer to the Driver 
Software Readme file on the CD fo r instructions (in English only).
Downloading updated drivers from the Internet
To download the latest version of drivers and software files from the HP Support site:
1. Refer to:  http://www.hp.com/support  .
2. Select your country/region.
3. Select   Download Drivers and Software  .
4. Enter the model number of your monitor. The software download pages for your  monitor are displayed.
5. Download and install the driver and software  files by following the instructions on 
the download pages.
6. Ensure that your system meets the requirements.
 
						

							
11 Appendix 4.   Operating the Monitor ENWW
 
Front-Panel Controls
 The monitor buttons are located on the bottom of the front panel
Figure 4-1 Front-panel control buttons
No. Icon Description
1PowerTurns the monitor on or puts it in standby or sleep mode. The Power 
button is located on the bottom or fr ont of the monitor depending on the 
model.
2Menu Opens, selects, or exits the OSD menu.
3+ Navigates forward through the OS D menu and increases adjustment 
levels.
4- Navigates backward through the OSD menu and decreases adjustment 
levels.
5Auto     To utilize the auto-adjustment feature,press the key and release it  immediately.To use input source selection function,press and hold the
                                                                        \
   key for 3 seconds (multi-source models).
 
						

							
ENWWUsing the On-Screen Display (OSD) 12
Using the On-Screen Display (OSD)
Main
Menu Item Main
Menu Icon 1st Sub
Menu Item 2nd Sub
Menu Item Description Adjust 
Range Reset Value
Luminance Contrast N/A Contrast from Digital-register. Each step will increase/
decrease value by 10-100 Recall Warm 
Contrast Value
Brightness N/A Backlight Adjustment Each step will increase/
decrease value by 1 0-100 Recall Warm 
Brightness Value
Eco Mode N/A Picture Adjustment, Brightness = 90,
Contrast = 50.
Brightness, Contrast 
Adjustable Standard Recall to 
Standard Mode 
Brightness = 20,
Contrast = 50.
Brightness, Contrast Grayed. Te x t
Brightness = 40,
Contrast = 50.
Brightness, Contrast
Grayed. Internet
Brightness = 60
Contrast = 50,
Brightness, Contrast Grayed Game
Brightness = 80,
Contrast = 50,
Brightness, Contrast Grayed Movie
Brightness = 100,
Contrast = 50,
Brightness, Contrast Grayed Spo rts
DCR N/A Dynamic contrast ratio On/Off Recall Off Value
 
						

							
13 Appendix 4.   Operating the Monitor ENWW
 
Main
Menu Item Main
Menu Icon 1st Sub
Menu Item 2nd Sub
Menu Item Description Adjust 
Range Reset Value
Image  Setup Clock N/A Adjust picture Clock to reduce 
Vertical-Line noise.
Each step will increase/
decrease value by 1 0-100 Do Auto 
Configure
Phase N/A Adjust Picture Phase to  reduce Horizontal-Line noise. 0-100 Do Auto 
Configure
H. Position N/A Adjust the horizontal position  of the picture. 0-100 Do Auto 
Configure
V. Position N/A Adjust the vertical position of  the picture. 0-100 Do Auto 
Configure
Image 
Ratio N/A Select Image Aspect Ratio Wide Default to panel 
native aspect ratio
 
						

							
ENWWUsing the On-Screen Display (OSD) 14
Main
Menu Item Main
Menu Icon Sub
Menu Item Description Adjust 
Range Reset Value
Color Temp. Warm Recall Warm Color  Temperature.N/A The Color 
Temperature will 
be set to Warm.
The User R/G/B 
value (default is 
50) will can be 
Modified by Reset 
function in user 
mode.
Normal Recall Normal Color 
Temperature. N/A
Cool Recall Cool Color  Temperature. N/A
sRGB
(for select 
models with 
sRGB 
function) Recall sRGB Color 
Temperature.
N/A
Red Red Gain from Digital- register.
Each step will increase/
decrease value by 1 0-100
Green Green Gain from Digital- register.
Each  step will increase/
decrease value by 1 0-100
Blue Blue Gain from Digital- register.
Each step will increase/
decrease value by 1 0-100