HP Proliant Dl360 Generation 5 Server User Guide

 
Setup 31 
•
 
Manual installation—Insert the operating system CD  into the CD-ROM drive and reboot the server. 
This process may require you to obtain additional drivers from the HP website 
( http://www.hp.com/support
). 
Follow the on-screen instructions to  begin the installation process. 
For information on using these installation paths, refe r to the SmartStart installation poster in the HP 
ProLiant Essentials Foundation Pack, included with the server. 
 
Registering the server 
To register the...

 
Hardware options  installation 32 
Hardware options installation 
In this section 
Introduction ........................................................................\
........................................... ........................ 32 
Processor  option........................................................................\
....................................... ...................... 32 
Memory op tions ........................................................................\...

 
Hardware options  installation 33 
6.
 
Open the processor retaining latch and  the processor socket retaining bracket. 
 
7. Remove the processor socket protective cover. 
 
  IMPORTANT:   Be sure the processor remains inside the processor installation tool.  

 
Hardware options  installation 34 
8.
 
If the processor has separated from the installation  tool, carefully re-insert the processor in the tool. 
 
9. Align the processor installation tool wi th the socket and install the processor. 
  

 
Hardware options  installation 35 
10.
 
Press down firmly until the proces sor installation tool clicks and separates from the processor, and 
then remove the processor installation tool. 
 
11.  Close the processor socket retaining bra cket and the processor retaining latch. 
  

 
Hardware options  installation 36 
12.
 
Remove the heatsink protective cover. 
 
13. Open the heatsink retaining latches. 
  

 
Hardware options  installation 37 
14.
 
Install the heatsink. 
 
15.  Install the processor air baffle. 
16. Install the power supply air baffle. 
17. Install the access panel (on page  20). 
18.  Slide the server into the rack. 
19. Power up the server (on page  18).  
Memory options 
This server contains eight FBDIMM slots. You ca n expand server memory by installing supported 
Registered DDR-2 FBDIMMs. 
 
Memory configurations 
The server supports the following Advanced Memory  Protection (AMP)...

 
Hardware options  installation 38 
•
 
FBDIMM pairs in a memory bank must  have identical HP part numbers. 
• FBDIMMS must be populated as spec ified for each AMP memory mode. 
The memory subsystem for this server  is divided into two branches. Each memory branch is essentially a 
separate memory controller. The FBDIMMs map to the tw o branches as indicated in the following table: 
 
Branch 0  Branch 1 
FBDIMM 1A  FBDIMM 5B 
FBDIMM 3A  FBDIMM 7B 
FBDIMM 2C  FBDIMM 6D 
FBDIMM 4C  FBDIMM 8D  
This...

 
Hardware options  installation 39 
current DRAM technology. If the cu rrent DRAM technology allows for 2-GB single-rank FBDIMMs, a dual-
rank FBDIMM using the same technology would be 4-GB. 
In online spare mode, a single rank  of memory acts as the spare memory. For single-rank FBDIMMs, the 
entire FBDIMM acts as the spare  memory. For a dual-rank FBDIMM, only half of the FBDIMM acts as the 
spare memory while the other half is availabl e for operating system and application usage. 
If one of the...

 
Hardware options  installation 40 
•
 
Banks A and B must be fully populated. 
• Bank A and bank B must contain FBDIMMs with iden tical part numbers. If installed, bank C and 
bank D must also contain FBDIMMs with identical part numbers. 
When using mirrored memory mode, FBDIMMs must be  populated as specified in the following table: 
 
Configuration Bank A 
1A and 3A Bank B 
5B and 7B Bank C 
2C and 4C Bank D 
6D and 8D 
1 X X — — 
2 X X X X  
After installing FBDIMMs, use RBSU to configure the...