Husqvarna Etech Ii 326l Manual

							MAINTENANCE
English – 211151471-95   Rev. 1  2009-01-16
Oiling the air filter
Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The 
filter oil contains a solvent to make it spread evenly through 
the filter. You should therefore avoid skin contact.
Put the filter in a plastic bag and pour the filter oil over it. 
Knead the plastic bag to distribute the oil. Squeeze the 
excess oil out of the filter inside the plastic bag and pour off 
the excess before fitting the filter to the machine. Never use 
common engine oil. This would drain through the filter quite 
quickly and collect in the bottom.
Bevel gear
(326L, 326LS, 326Lx, 326LDx)
The bevel gear is filled with the right quantity of grease at the 
factory. However, before using the machine you should check 
that the bevel gear is filled three-quarters full with grease. Use 
HUSQVARNA special grease.
The grease in the bevel gear does not normally need to be 
changed except if repairs are carried out.
CAUTION! Use only HUSQVARNA replacement parts. Use 
of other brands of replacement parts can cause damage to 
your unit or injury to the operator or others. Your warranty 
does not cover damage or liability caused by the use of 
accessories and/or attachments not specifically 
recommended by HUSQVARNA. 
						

							MAINTENANCE
22 – English1151471-95   Rev. 1  2009-01-16
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the 
Maintenance section.
MaintenanceDaily 
maintenanceWeekly 
maintenanceMonthly 
maintenance
Clean the outside of the machine.X
Make sure the throttle trigger lock and the throttle function correctly from a 
safety point of view.X
Check that the stop switch works correctly.X
Check that the cutting attachment does not rotate at idle.X
Clean the air filter. Replace if necessary.X
Check that the guard is undamaged and not cracked. Replace the guard if 
it has been exposed to impact or is cracked.X
Check that the trimmer head is undamaged and not cracked. Replace the 
trimmer head if necessary.X
Check that the locking nut of the cutting equipment is tighten correctly.X
Check that nuts and screws are tight.X
Check that there are no fuel leaks from the engine, tank or fuel lines.X
Check the starter and starter cord.X
Check that the vibration damping elements are not damaged.X
Clean the outside of the spark plug. Remove it and check the electrode 
gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug. Check that 
the spark plug is fitted with a suppressor.
X
Clean the machine’s cooling system.X
Clean or replace the spark arrestor screen on the muffler (only applies to 
mufflers without a catalytic converter).X
Clean the outside of the carburettor and the space around it.X
Check that the bevel gear is filled three-quarters full with lubricant. Fill if 
necessary using special grease.X
Check the fuel filter from contamination and the fuel hose from cracks or 
other defects. Replace if necessary.X
Check all cables and connections.X
Check the clutch, clutch springs and the clutch drum for wear. Replace if 
necessary by an autorized service workshop.X
Replace the spark plug. Check that the spark plug is fitted with a 
suppressor.X
Check and clean the spark arrestor screen on the muffler (only applies to 
mufflers fitted with a catalytic converter).X
Check and if necessary, clean the exhaust port of cylinder from carbon 
deposits.X 
						

							TECHNICAL DATA
English – 231151471-95   Rev. 1  2009-01-16
Technical data
Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various 
working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.
NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting 
equipment fitted. The table indicates the highest and lowest values.
326C326L/326LS326Lx326LDx
Engine
Cylinder displacement, cu.in/cm31,50/24,51,50/24,51,50/24,51,50/24,5
Cylinder bore, inch/mm1,34/34,01,34/34,01,34/34,01,34/34,0
Stroke, inch/mm1,06/271,06/271,06/271,06/27
Idle speed, rpm2700270027002700
Recommended max. fast idle speed, rpm11000-1170011000-1170011000-1170011000-11700
Speed of output shaft, rpm11700801480148014
Max. engine output, acc. to ISO 8893, kW/ rpm0,9/84000,9/84000,9/84000,9/8400
Catalytic converter mufflerYe sYe sYe sYe s
Speed-regulated ignition systemNoYe sYe sYe s
Ignition system
Manufacturer/type of ignition systemWalbroMB/ 
SEM AM49
WalbroMB/ 
SEM AM49
WalbroMB/ 
SEM AM49
WalbroMB/ 
SEM AM49
Spark plugChampion RCJ 6YChampion RCJ 6YChampion RCJ 6YChampion RCJ 6Y
Electrode gap, inch/mm0,02/0,50,02/0,50,02/0,50,02/0,5
Fuel and lubrication system
Manufacturer/type of carburetorZama C1QZama C1QZama C1QZama C1Q
Fuel tank capacity, US pint/litre1,06/0,51,06/0,51,06/0,51,06/0,5
Weight
Weight without fuel, cutting attachment and 
guard, Lbs/kg9,5/4,39,0/4,19,7/4,49,9/4,5
Sound levels
(see note 1)
Equivalent sound pressure level at the user′s 
ear, measured according to ANSI  B175.3-1997, 
dB(A), min/max:
91/9891/9791/9791/98
Vibration levels
Vibration levels at handles, measured according 
to ANSI B175.3-1997, m/s2
At idle, left/right handles, min.:2,7/1,51,7/1,51,7/1,51,7/1,5
At idle, left/right handles, max.:3,5/1,72,7/1,82,7/1,82,8/1,8
At max. speed, left/right handles, min.:4,4/4,83,9/5,23,9/5,23,9/5,2
At max. speed, left/right handles, max.:5,7/5,77,2/9,87,2/9,87,2/9,8 
						

							TECHNICAL DATA
24 – English1151471-95   Rev. 1  2009-01-16
The accessories are recommended for use in combination with the specified power heads and have been evaluated to applicable 
ISO- and EN safety requirement standards by the Swedish Machinery Testing Institute.
The accessories have been developed mainly for the Husqvarna 125LD trimmer, but can also be used in combination with the 
specified power heads and have been evaluated to applicable ISO- and EN safety requirement standards by the Swedish 
Machinery Testing Institute.
The accessories used in combination with the specified power heads have been evaluated to ANSI B175.3-2003 Grass Trimmers 
and Brushcutters - Safety Requirements. These combinations have been evaluated by Underwriters Laboratories Inc. (UL) and are 
consequently UL listed.
Powerhead modelAccessoriesArt No.
326LDx
Hedge trimmer attachment with shaft HA 110537 19 66-01
Hedge trimmer attachment with shaft HA 850537 19 66-02
Clean sweep attachment with shaft SR600537 19 67-01
Edger attachment with shaft537 19 69-01
Saw attachment with shaft PA 1100537 18 33-17
Cultivator attachment with shaft CA 150537 42 54-01
326L, 326LS, 326LxSaw attachment without shaft PA537 18 33-12
Powerhead modelAccessoriesArt No.
326LDx
Cultivator attachment CAC952 71 19-07
Edger attachment EAC952 71 19-08
Pole saw attachment PAC952 71 19-10
Blower attachment BAC952 71 19-11
Hedge trimmer attachment HAC952 71 19-21
Powerhead modelAccessoriesTypeCutting attachment guard, 
Art. no.
326C
Blade shaft thread 3/8 R
Plastic bladesTricut Ø 230 mm (R)537 02 61-01 / 537 07 67-01
Trimmer head
Trimmy Hit Junior (R)537 02 61-01 / 537 07 67-01
Trimmy Fix (R)537 02 61-01 / 537 07 67-01
Trimmy Hit VII (R)537 02 61-01 / 537 07 67-01
T25 (R)537 02 61-01 / 537 07 67-01
T25C537 02 61-01 / 537 07 67-01
326L, 326LS, 326Lx, 326LDx
Arbor shaft thread M10
Plastic bladesTricut Ø 300 mm503 93 42-02
Trimmer head
Trimmy H II 1503 93 42-02 /  503 97 71-01
Trimmy Fix503 93 42-02 /  503 97 71-01
Trimmy Hit503 93 42-02 /  503 97 71-01
Trimmy Hit Pro503 93 42-02 /  503 97 71-01
Superauto II 1503 93 42-02 /  503 97 71-01
T25 (L)537 02 61-01 / 537 07 67-01
S35503 93 42-02 /  503 97 71-01
T35503 93 42-02 /  503 97 71-01
Art No.
326LDxShaftTA 850537 35 35-01 
						

							FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT
English – 251151471-95   Rev. 1  2009-01-16
YOUR WARRANTY RIGHTS AND 
OBLIGATIONS
The EPA (U.S. Environmental Protection Agency), CARB 
(California Air Resources Board), Environment Canada and 
Husqvarna Forest & Garden are pleased to explain the 
emissions control system’s warranty on your 2009 and later 
small off-road engine. In U.S. and Canada, new equipment 
that use small off-road engines must be designed, built, and 
equipped to meet the applicable Federal or Californian 
stringent anti-smog standards. Husqvarna Forest & Garden 
must warrant the emissions control system on your small off-
road engine for the period listed below provided there has 
been no abuse, neglect or improper maintenance of your 
equipment. Your emissions control system may include parts 
such as the carburetor, ignition system, catalytic converter, 
fuel tank, filters and other associated components. Also, 
included may be hoses, belts, connectors, sensors, and other 
emission-related assemblies. Where a warrantable condition 
exists, Husqvarna Forest & Garden will repair your small off-
road engine at no cost to you including diagnosis, parts and 
labor.
MANUFACTURER′S WARRANTY 
COVERAGE
The emissions control system is warranted for two years. If 
any emissions-related part on your equipment is defective, 
the part will be repaired or replaced by Husqvarna Forest & 
Garden.
OWNER′S WARRANTY  RESPONSIBILITIES
•As the small off-road engine owner, you are responsible 
for performance of the required maintenance listed in your 
operator’s manual. Husqvarna Forest & Garden 
recommends that you retain all receipts covering 
maintenance on your small off-road engine, but 
Husqvarna Forest & Garden cannot deny warranty solely 
for the lack of receipts or your failure to ensure the 
performance of all scheduled maintenance.
• As the small off-road engine owner, you should however 
be aware that Husqvarna Forest & Garden may deny you 
warranty coverage if your small off-road engine or a part 
has failed due to abuse, neglect, or improper maintenance 
or unapproved modifications.
• You are responsible for presenting your small off-road 
engine to a Husqvarna Forest & Garden distribution 
center or service center as soon as the problem exists. 
The warranty repairs should be completed in a reasonable 
amount of time, not to exceed 30 days.If you have any 
questions regarding your warranty rights and 
responsibilities, you should contact your nearest 
authorized servicing dealer or call Husqvarna Forest & 
Garden at 1-800-487-5951 or visit 
www.usa.husqvarna.com.
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date the engine or 
equipment is delivered to an ultimate purchaser.
LENGTH OF COVERAGE
Husqvarna Forest & Garden warrants to the ultimate 
purchaser and each subsequent owner that the engine or 
equipment is designed, built, and equipped so as to conform 
with all applicable regulations adopted by EPA and CARB, and is free from defects in materials and workmanship that 
causes the failure of a warranted part for a period of two 
years.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS Repair or 
replacement of any warranted part under the warranty must 
be performed at no charge to the owner at a warranty station. 
Warranty services or repairs will be provided at all Husqvarna 
Forest & Garden distribution centers that are franchised to 
service the subject engines. Throughout the emissions 
warranty period of two years, Husqvarna Forest & Garden 
must maintain a supply of warranted parts sufficient to meet 
the expected demand for such parts.
WARRANTY PERIOD Any warranted part that is scheduled 
for replacement as required in the maintenance schedule, is 
warranted for the period of time prior to the first scheduled 
replacement point for that part. If the part fails prior to the first 
scheduled replacement, the part will be repaired or replaced 
by Husqvarna Forest & Garden at no cost. Any such part 
repaired or replaced under warranty is warranted for the 
remainder of the period prior to the first scheduled 
replacement point for the part. Any warranted part that is not 
scheduled for replacement as required in the maintenance 
schedule, is warranted for two years. If any such part fails 
during the period of warranty coverage, it will be repaired and 
replaced by Husqvarna Forest & Garden at no cost. Any such 
part repaired or replaced under the warranty is warranted for 
the remaining warranty period. Any warranted part that is 
scheduled only for regular inspection in the maintenance 
schedule will be warranted for a period of two years. A 
statement in such written instructions to the effect of ”repair or 
replace as necessary” will not reduce the period of warranty 
coverage. Any such part repaired or replaced under warranty 
will be warranted for the remaining warranty period.
DIAGNOSIS The owner must not be charged for diagnostic 
labor that leads to the determination that a warranted part is 
in fact defective, provided that such diagnostic work is 
performed at a warranty station.
CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden 
is liable for damages to other engine components proximately 
caused by a failure under warranty of any warranted part.
EMISSION WARRANTY PARTS LIST
1Carburetor and internal parts
2 Intake pipe, airfilter holder and carburetor bolts.
3 Airfilter and fuelfilter covered up to maintenance schedule.
4 Spark Plug, covered up to maintenance schedule
5 Ignition Module
6 Muffler with catalytic converter
7 Fuel tank
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper 
maintenance are not covered. 
						

							FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT
26 – English1151471-95   Rev. 1  2009-01-16
ADD -ON OR MODIFIED PARTS
Add-on or modified parts that are not exempted by CARB or 
EPA may not be used. The use of any non-exempted add-on 
or modified parts will be grounds for disallowing a warranty 
claim. Husqvarna Forest & Garden will not be liable to warrant 
failures of warranted parts caused by the use of a non-
exempted add-on or modified part.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights and 
responsibilities, you should contact your nearest authorized 
servicing dealer or call Husqvarna Forest & Garden at 1-800-
487-5951 or visit www.usa.husqvarna.com.
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs are provided through all 
Husqvarna Forest & Garden authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND 
REPAIR OF EMISSION-RELATED PARTS
Any replacement part may be used in the performance of any 
warranty maintenance or repairs and must be provided 
without charge to the owner. Such use will not reduce the 
warranty obligations of the manufacturer.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all required 
maintenance, as defined in the operator’s manual. 
						

							1151471-95   Rev. 1  2009-01-16
1 Trimmy Hit Junior
2
5
6
7
89
10
12
“Click”
3
4
5,75 m
   19
2,0-2,4 mm
.080-.095
15 cm
     6
~ 2,8 m
    9
1.)
2.)
11
15 cm
     6
15 cm
     6 
						

							1151471-95   Rev. 1  2009-01-16
6
2) 1)
~ 15 cm    6
7
89
1011
15 cm
123
4
56
7,0 m   23
2,0- mm
,080-.
12 cm 5
~ 3,5 m    11
Trimmy VII 
						

							1151471-95   Rev. 1  2009-01-16
Clic
1
2
3
5
67
9
6,0 m
18
4
8
3,05 m
9
2,0-2,4 mm.079-.095
10 cm
     4
6 15 cm
T25 
						

							1151471-95   Rev. 1  2009-01-16
2
4
3
2,0-2,4 mm
.079-0.095
2,75 m
92,75 m
9
6 15 cm
5
61
T25C