Husqvarna Rider 13 C Manual

English – 31
Maintenance
Checking the blades
To achieve the best mowing results it is important that the 
blades are undamaged and well-sharpened.
Check that the blades’ attachment screws are tight.
The blades should be balanced after sharpening.
Damaged blades should be replaced when hitting obstacles 
that result in a breakdown. Let the servicing dealer judge 
whether the blade can be repaired/ground or must be 
discarded.
Removing the BioClip plug
To change a Combi unit from BioClip function to...

32 – English
Lubrication
Checking the engine’s oil level.
Check the oil level in the engine when the Rider stands 
horizontal with the engine switched off.
Open the engine cover.
Loosen the dipstick, pull it up and wipe it off.
 The dipstick should be completely screwed down
Pull the dipstick out again and read the oil level.
The oil level should be between the markings on the dipstick. 
If the level is approaching the ADD mark, top up the oil to the 
FULL mark on the dipstick.
The oil is topped up...

English – 33
Lubrication
Checking the oil level in the 
transmission on Rider 13 C, Rider 13 
AWD and Rider 15 C
1Remove the transmission cover. Undo the two screws 
(one on each side) and lift off the transmission cover.
2Rider 13 C and Rider 15 C Check that there is oil in the 
transmission’s oil tank. Fill if necessary with engine oil 
SAE 10W/30 (class SF–CC).
Rider 13 AWD
Check that there is oil in the transmission’s oil tank. Fill if 
necessary with engine oil SAE 10W/40 (class SF–CC).
The oil and...

34 – English
Troubleshooting schedule
ProblemProcedure
Engine does not startThere is no fuel in the fuel tankSpark plug defectiveFaulty spark plug connections or interchanged cablesDirt in the carburettor or fuel lineStarter motor does not turn over the engine
Starter motor does not turn over the engineBattery flatBad contact between the cable and batteryLift lever for cutting unit in wrong positionMain fuse blown.This fuse is in front of the battery, under the battery cover.Ignition lock faultyHydrostat...

English – 35
Storage
Winter storage
At the end of the season, or if the machine is going to stand 
idle for more than 30 days, it should immediately be made 
ready for storage. Fuel which is left to stand for long periods 
(30 days or more) can leave tacky deposits which can block 
the carburettor and interfere with the engine.
Fuel stabiliser is an acceptable alternative to avoid tacky 
deposits during storage. If alkylate petrol (Aspen) is used 
stabiliser is not necessary since this fuel is stable....

36 – English
TECHNICAL DATA
Rider 11Rider 11 C
Dimensions
Length without cutting unit, mm/ft-2010/6,58
Length with cutting unit, mm/ft2040/6,692200/7,22
Width without cutting unit, mm/ft-900/2,89
Width with cutting unit, mm/ft960/3,151114/3,65
Height, mm/ft1070/3,521070/3,52
Operating weight with cutting deck, kg/lb229/505229/505
Wheel base, mm/ft820/2,69855/2,8
Track width, mm/ft610/2625/2,05
Tyre dimensions165/60-8165/60-8
Air pressure, rear - front, kPa / kp/cm3 / PSI60 (0,6/8,5)60 (0,6/8,5)
Max....

English – 37
TECHNICAL DATA
Rider 13 CRider 13 AWD
Dimensions
Length without cutting unit, mm/ft2010/6,582010/6,58
Length with cutting unit, mm/ft2220/7,292220/7,29
Width without cutting unit, mm/ft880/2,89880/2,89
Width with cutting unit, mm/ft1114/3,651114/3,65
Height, mm/ft1070/3,521070/3,52
Operating weight with cutting deck, kg/lb232/511270/595
Wheel base, mm/ft855/2,8855/2,8
Track width, front, mm/ft715/2,37715/2,37
Track width, rear, mm/ft625/2,05625/2,05
Tyre dimensions165/60-8165/60-8
Air...

38 – English
TECHNICAL DATA
´®z+R?@¶6|¨
´®z+R?@¶6|¨
Rider 15 C
Dimensions
Length without cutting unit, mm/ft2010/6,58
Length with cutting unit, mm/ft2220/7,29
Width without cutting unit, mm/ft880/2,89
Width with cutting unit, mm/ft1114/3,65
Height, mm/ft1070/3,52
Operating weight with cutting deck, kg/lb249/549
Wheel base, mm/ft855/2,8
Track width, front, mm/ft715/2,37
Track width, rear, mm/ft625/2,05
Tyre dimensions165/60-8
Air pressure, rear - front, kPa / kp/cm3 / PSI60 (0,6/8,5)
Max. gradient10°...

English – 39
TECHNICAL DATA
 
 
 
EC-declaration of conformity (Applies to Europe only)
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel.: +46-36-146500, hereby declares that Husqvarna Rider 11, Rider 11 C, Rider 
13 C, Rider 13 AWD and Rider 15 C from 2005s serial numbers and onwards (the year is clearly stated in plain text on the ratin g 
plate with subsequent serial number), complies with the requirements of the COUNCILS DIRECTIVE:
of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
of May...

´®z+R?@¶6|¨
2006-10-26
´®z+R?@¶6|¨
1150313-26