Husqvarna X Series 125bvx Manual
Here you can view all the pages of manual Husqvarna X Series 125bvx Manual. The Husqvarna manuals for Blower are available online for free. You can easily download all the documents as PDF.
Page 1
125B 125B 125BVX-SERIES X-SERIES EN 2-20 FR 21-40 ES 41-60
Page 2
English --- 2 115277126 Rev. 2 5/1/10 CONTENTS Contents Introduction 2 ................... Key to symbols 3 .................. Safety instructions 4 ............... Description 6 ..................... Fuel handling 11 .................... Start and stop 12 ................... Using the blower 13 ................. Maintenance 16 .................... Technical data 19 ................... WARNI NG :Under no circum- stances may the design of the machine be modified without the permission of the...
Page 3
English --- 3 115277126 Rev. 2 5/1/10 KEY TO SYMBOLS Checks and/or main- tenance shall be carried out after having switched off the engine and discon- nected the spark plug. Cleaning at regular intervals is required. Approved protective goggles or visor must be worn. Approved protective goggles or visor, ear protection, and face mask in dusty environ- ments must be worn. WARNING! The blow- er can be dangerous! Careless or improper use can cause seri- ous, even fatal injury. Read the operator’s manual...
Page 4
English --- 4 115277126 Rev. 2 5/1/10 SAFETY INSTRUCTIONS MufflerThe muffler is designed to give the lowest possible noise level and to direct the en- gine’s exhaust fumes away from the opera- tor. Mufflers fitted with catalytic converters are also designed to reduce harmful ex- haust components. Safety equipment The blower is equipped with a number of safety devices and guards for the preven- tion of accidents. These are described in the general description of the blower. The safety devices and guards...
Page 5
English --- 5 115277126 Rev. 2 5/1/10 SAFETY INSTRUCTIONS Other safety measuresS Operate the blower only at reasonable hours, i.e. not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordi- nances. Usual recommendations are 9:00 a.m. to 5:00 p.m., Monday through Satur- day. S Operate the blower at the lowest possible throttle setting to do the job. S Check the condition of the blower before operation, especially the muffler, air intake and air...
Page 6
English --- 6 115277126 Rev. 2 5/1/10 DESCRIPTION The blower 20 23 24 13 15 14 17 19 12 10 9 8 6 3 1 4 7 11 2 1. Shoulder strap (125BVX-- SERIES) 13. Fan impeller 2. Throttle trigger 14. Standard nozzle 3. STOP switch 15. High velocity nozzle 4. Variable speed control (125B X-- SERIESand 125BVX-- SERIES) 5. Fan housing 16. Blower tube 6. Fuel cap 17. Tube clamp bolt 7. Air filter 18. Tube clamp nuts 8. Choke 19. Muffler 9. Primer bulb 20. Ground wire 10. Inlet cover 21. Starter handle 11. Vacuum handle...
Page 7
English --- 7 115277126 Rev. 2 5/1/10 DESCRIPTION Accessories (125BX--SERIESand 125BVX--SERIES) 24 22 21. Vacuum device with collection components consisting of items 22-- 26 below 22. Collection bag tube 23. Collection bag 24. Vacuum tube in two sections 25. Screw 26. Shoulder strap23 21 25 26
Page 8
English --- 8 115277126 Rev. 2 5/1/10 DESCRIPTION Safety equipmentThe following equipment on the blower is designed for protecting personnel and materials. These components should receive special attention whenever you operate, inspect and service the blower. Stop switchS The stop switch (A) is used to stop the engine. MufflerSThe muffler is designed to give the low- est possible noise level and to direct the engine’s exhaust fumes away from the operator. Mufflers fitted with catalytic converters are...
Page 9
English --- 9 115277126 Rev. 2 5/1/10 DESCRIPTION Ground wireS The ground wire (G) reduces static build-- up during operation in dry condi- tions. Inlet coverSAn inlet cover (H) is located on the side of the fan housing. Opening this cover allows access for cleaning and inspect- ing the impeller ( 125B X-- SERIESand 125BVX-- SERIESonly). If the vacuum tube is used, it must be fitted to the opening in the inlet cover. To open the inlet cover, use a tool to lift the edge of the cover opposite the hinge...
Page 10
English --- 10 115277126 Rev. 2 5/1/10 DESCRIPTION Adjusting the carburetor NOTFORALLMODELS S There are three adjusting screws (R) for adjusting the carburetor: SLow speed jet S High speed jet S Adjustment screw for idling S Adjusting the carburetor involves adapt- ing the engine to local operating condi- tions, e.g. climate, altitude, gasoline and type of two-- stroke engine oil used. For details about carburetor adjustment, see the Maintenance section. R ChokeSThe choke (Q) is located below the air...