Hyundai H Lcd1917 Instruction Manual

							LCD TV
Руководство по эксплуатации 
Instruction manual
H-LCD1917
ТЕЛЕВИЗОР
ЦВЕТНОГО ИЗОБРАЖЕНИЯ
ЖИДКОКРИСТАЛЛИЧЕСКИЙ (LCD)
 
						

							Table of contents 
Before you start 
Utilization of the product 
Important safeguards
Connection
InstallationBase installation
Wall mounting
Operation
Control elements  Front panel
 Back panel
Remote controller Changing the battery
General operations  Signal sources
OSD operation Picture setting
Sound setting
OSD setting
 Advance setting Function setting
USB operation File playback
General information
Troubleshooting Causes of interference
Accessories
Specifications
2 3
Table of contentsBefore you start
Dear customer!Thank you for purchasing our product. For safety, it is strongly recommended to read 
this manual carefully before connecting, operating and/or adjusting the product and keep 
the manual for reference in the future.
2
3
3
3
4
4
4
4
5
5
5
5
6
6
7
7
7
7
8
8
8
8
9
9
10
10
10
11
11
Downloaded From TV-Manual.com Manual” 
						

							23
Table of contentsBefore you start
If you want to dispose this product, do not mix it with general household waste. There is 
a separate collection system for used electronic products in accordance with legislation 
that requires proper treatment, recovery and recycling. Please contact your local authorities for the correct method of disposal. By doing so, 
you will ensure that your disposed product undergoes the necessar y treatment, recovery 
and recycling and thus prevent potential negative effects on the environment and human 
health.
Utilization of the product
Important safeguards
•  Before connecting the AC power cord to 
the mains supply outlet, make sure that the 
voltage designation of the unit corresponds to 
the local electrical supply.
•  Please unplug the power cord from the AC 
outlet and contact a service center for repair 
if following occurs: any obvious abnormality 
appears in the unit, such as smoky, peculiar 
smell or strange sound; liquid has been spilled or 
other objects have fallen into the unit; no picture 
or sound; cover or panel is broken; although you 
have operated the unit following the operating 
instructions, it still cannot work normally. •  This unit should only be connected to a 
wall socket having grounding.
•  Always disconnect the power cord and 
antenna during a storm. •  Do not fix the power cord with a metal nail.
•  Unplug the power cord from the AC outlet; 
also unplug the signal cables from the input 
ports when the unit is unused for long periods 
of time. •  When unplugging the plug, always hold 
the wide slot, do not touch the metal part, and 
do not destroy, refit, twist, pull or roast the 
power cord.
•  Please contact the service center 
immediately if you found that the core is 
showed in the air or has been broken. •  Please replace the AC outlet if the metal  bolt cannot be inserted into the power socket 
completely or it cannot be fastened even when 
it was pushed in, otherwise, any accidents of 
shocks and fires would happen.
•  Never touch the antenna lie or power plug 
if it stars to thunder. •  Do not touch the power plug with wet 
hands. •  Do not use any non-rated power socket 
with numerous devices jointed on one power 
socket or cable device. The wire of non-
designated capacity may cause the fire due to 
the generation of heat. •  All instructions must be read and 
understood well before you operate the unit. 
Heed all warnings and follow all instructions. •  Please use the accessories provided 
by the manufacturer. Using inadequate 
accessories may result in accidents. •  Please adjust the product through the 
panel buttons or the remote controller, do 
not remove the cover or attempt to service 
the product by yourself. Do not disassemble 
back cover and do not make maintenance by 
yourself to avoid the electric shock. •  Over-press the panel may destroy the 
product. •  Do not place the product on an unstable 
cart, stand surface, tripod, bracket, or table. 
The product may fall, causing serious accidents 
as well as the damage to the product.  •  Please place the product on a flat surface 
in a well-ventilated location. Keep it away from 
Downloaded From TV-Manual.com Manual” 
						

							4
Before you start/Connection
the burning-light, direct sunlight, vibration, 
high-temperature and humidity.• Do not place any vase, potted plant, cup, 
medicine and any container with water on this 
product. If the liquid is spilt, it may cause the 
fire, electric shock or breakdown. •  Do not install it at the place on the strong 
magnetic field or current field. It may cause 
break down. This equipment may be observed 
deterioration of the picture by electromagnetic 
radiation in electromagnetic environment. •  Fasten the wheel of the product or shelf 
with wheels when installing this product. If it 
moves or is tipped over, it may be damaged. •  Do not place any fire source such as 
candlelight close to this product or place it on 
this product. If it is tipped over or fallen down, it 
may cause damage or fire. •  Do not place the unit into closed space 
of TV for better ventilation; it can reduce the 
product lifetime. Keep a space at list 10 cm at 
above, left, and right of the TV. •  Please place all the signal cords behind of 
rear panel. •  Do not overexert or touch the panel when 
you convey the product. Do not transfer the 
LCD TV up or down display direction. •  Do not transport it with the power cord 
or the connection cable connected. If you 
move this product with the power cord or the 
connection cable connected, the damaged 
power cord, connection cable or connection 
terminal may cause the fire, the electric shock 
or breakdown. •  2 persons or more shall transport the 
device, which is heavier than 18 kg. If you drop 
or tip over the device, it may damage it. •  The temperature of the product’s body 
becomes a little higher after a long period use. 
This phenomenon indicates that heat exchange 
in normal working mode, thus please do not 
let children or anyone who is sensitive of 
temperature to touch.
All images provided herein are schematic 
drawings of real objects and may differ 
from their real images.Connection
•  Insert the power cord to the power 
connector of this unit, then connect the cord 
plug to a power supply source. •  Connect a video source to the Composite 
video input jack with RCA cable. •  Connect an audio source to the proper 
Audio input jacks (Left and Right). •  Connect a TV or CATV antenna to the 
antenna jack. •  Connect PC audio input to PC main unit 
with related audio cable in PC mode. •  If the video source has a HDMI output 
jack, you can connect the signal to the unit by 
HDMI cable. •  When using the unit as a computer screen, 
connect the PC to the VGA jack of the unit by 
the relevant cable. •  Component input is intended for receiving 
component video signal if connected to the 
component output of external signal source.
•  Connect your headphones or earphones 
(not included) to the headphone socket of this 
unit. When headphones are connected, the 
sound output through the built-in speakers of 
this unit is mute.
Installation
Base instalation
Insert the stand into the fixing slit in the rear 
bottom of the TV. Fasten the screw.
Wall mountingTake off the stand. For wall mounting you 
should use screw holes on the rear of the unit 
and wall mounting stand, bracket and screws 
not included.
Downloaded From TV-Manual.com Manual” 
						

							5
Operation
Front panel
1
2
3
4
5
6
7
 
Control elements    
       1. SOURCE button
        2. CH+/CH- buttons
        3. VOL+/VOL- buttons
        4. MENU button
        5. IR remote sensor
        6. POWER button
        7. Power indicator
        
Back panel
1 23 4567 8
9 10 1112 13
14
15
16
17
18
1. HDMI-1 input
2. VGA input
3. PC audio input
4. Component video input
5. Component audio input (L+R)
6. Composite video output 7. Audio stereo output (L+R)
8. TV antenna jack
9. Composite video input-1
10. Audio stereo input-1
11. S-Video input
12. Audio stereo input-2
13. Composite video input-2
14. Headphone output
15. HDMI-2 input
16. USB port
17. AC cord inlet
18. Power switch
Downloaded From TV-Manual.com Manual” 
						

							6
Operation
Remote controller (RC)
1.  POWER button
2.  Number buttons (Alphabetic function is 
unavailable for this model)
3.  F1 button
4.  SMART S. button
5.  MENU button
6.  VOL+/VOL- buttons
7.  Cursor (UP/DOWN/LEFT/RIGHT) buttons/
OK button
8.  TIME button9.  INFO button
10. Button not operable 
11. COLOR button
12. Button not operable
13. MUTE button
14. PROGRAM LIST button
15. SMART P. button
16. SOURCE button
17. CH+/CH- buttons
18. RETURN button
19. 16:9 button
20. P/N button
21. AUDIO button (not operable)
Changing the battery1.  Remove the battery compartment cover 
on the back of the RC. 2.  Insert the batteries into the battery 
compartment making sure that the correct 
polarity is observed. 3.  Install the cover back.
•  Use two AAA batteries for the RC. The RC 
should be pointed at remote sensor within 8 
meters and within 30 degrees at the left or the 
right side.
•  Take the battery out of the RC if it is not 
used for a long time. •  Do not mix new and used batteries or 
different types of batteries. Weak batteries can 
leak and severely damage the RC. •  Do not expose the RC to shock, liquids, 
and do not place it in an area with high 
humidity.
1 23
1
2
3
4
5
6
7
8
9
10
11 12
13
14
15
16
17
18
19
20
21
Downloaded From TV-Manual.com Manual” 
						

							7
Operation
General operations
•  Press POWER button on the unit or on the 
RC to switch on the unit from standby mode. 
Press POWER switch on the unit to switch off 
power. When the unit is on, press POWER 
button on the RC to switch the unit to standby.
  When no signal input for 5 minutes, the 
unit will switch to standby mode automatically. •  Press VOL- button repeatedly to decrease 
the volume; press VOL+ button repeatedly to 
increase the volume. •  Press TIME button repeatedly to set the 
sleep time (from 0 to 120 min). •  Press RETURN button on the RC to select 
from the present channel and the previously 
displayed channel. •  Press 16:9 button repeatedly to select 
a screen display size from the available list: 
FULL => MOVIE => CAPTION => 4:3 => 
PANORAMA. Available aspects may differ for 
different signal sources. •  Press MUTE button to cut off sound, press 
this button again or adjust volume to resume 
sound. •  Select the TV function mode. Press 
CH-/CH+ buttons to select previous or next 
channels; or press number buttons to enter a 
channel number directly. •  Press SMART P. button repeatedly to 
cycle through the available video picture 
modes from the following types: Standard => 
Dynamic => Soft => Personal. •  Press SMART S. button repeatedly to 
cycle through the available sound modes from 
the following types: Personal => Standard => 
News => Music. •  Press INFO button to display the preset 
TV channel play information. •  Press P/N button to select PAL/NTSC/Auto 
color system. •  Press COLOR button to select Normal/
Warm/Cool color temperature mode. •  Press F1 button to freeze the picture on 
or off. •  Press PROGRAM LIST button to scan or 
set program list.
Signal sourcesPress SOURCE button, then press DOWN/
UP cursor buttons on the RC or CH+/CH- 
buttons on the panel to select a source from 
available source list: TV => AV1 => AV2 => 
SVideo => YPbPr => HDMI1 => HDMI2 => PC 
=> USB. Press OK button on the RC or MENU 
button on the panel to confirm.
OSD operation
1. Press MENU button to enter the setting 
menu displayed on the screen. 2. Press LEFT/RIGHT cursor buttons on the 
RC or VOL+/VOL- buttons on the panel to go 
to the needed setting page. 3. Press UP/DOWN cursor buttons on the 
RC or CH+/CH- buttons on the panel to select 
a parameter to adjust. 4. Press LEFT/RIGHT buttons on the RC or 
VOL+/VOL- buttons on the panel to adjust the 
selected parameter. 5. Press MENU button to return to the root 
menu or exit menu setting.
  Some menu items may be in grey color, 
in this case they are not adjustable. Pictures 
of OSD manu are for reference only; they may 
differ from the real pictures.
Picture setting
PICTURE
CONTRAST
BRIGHTNESS
HUE
SATURATION
SHARPNESS
PICTURE MODE
SCALE
COLOR TONE
3D NR
      SEL              ADJ    MENU : EXIT
•  Contrast,  Brightness,  Hue (available only 
for NTSC system), Saturation, Sharpness.
Downloaded From TV-Manual.com Manual” 
						

							89
OperationOperation
•  Picture Mode: Standard/Dynamic/Soft/
Personal. •  Scale: Full/Movie/Caption/4:3/Panorama.
•  Color tone: Select color temperaure mode 
of the picture - Normal/Warm/Cool. •  3D NR: Middle/Strong/Weak/Off.
Sound setting
SOUND
BASS
TREBLE
BALANCE
SOUND MODE
      SEL              ADJ    MENU : EXIT
•  Bass, Treble, Balance (adjust output 
between left and right speakers). •  Sound Mode: Standrard/News/Music/
Personal.
OSD setting
OSD
      SEL              ADJ    MENU : EXIT
OSD-H POSITION
OSD-V POSITION
OSD-DURATION
OSD-HALFTONE
OSD-LANGUAGE
•  OSD-H Position, OSD-V Position: adjust 
horizontal and vertical position of the OSD menu. •  OSD-Duration: set OSD menu display 
time from 5 to 60. •  OSD-Halftone: adjust the tone of the OSD 
menu. •  OSD-Language: select the language of 
the OSD menu.
Advance setting
      SEL              ADJ    MENU : EXIT
ADVANCE
SLEEP-TIMER
DCC
BLUE SCREEN
RESETTING
•  Sleep-timer: set the sleep time in minutes 
(15M, 30M, 45M, 60M, 120M).  •  DCC: set on or off dynamic contrast control. 
•  Blue screen: set on or off blue screen.
•  Resetting: reset the parameters to initial 
factory settings. 
TV setting
TV
      SEL              ADJ    MENU : EXIT
COLOR SYSTEM
SOUND SYSTEM
MTS
SKIP
AUTO SCAN
MANUAL SEARCH
FINE TUNING
CHANNEL EDIT
•  Color system: PAL/NTSC/AUTO.
•  Sound system: select sound system: I, 
D/K, M, AUTO, B/G. •  MTS: select an MTS mode: STEREO/
MONO/DUAL I/DUAL II. •  Skip: set on or off skipping a channel.
•  Auto scan: press RIGHT cursor button 
on the RC or VOL+ button on the panel to 
Downloaded From TV-Manual.com Manual” 
						

							89
OperationOperation
start automatical search of available channels. 
Current frequency and and channel number 
will be displayed. To stop search, press MENU 
button on the RC.
•  Manual search: press RIGHT cursor 
button on the RC or VOL+ button on the panel 
to enter manual search mode. Press LEFT/
RIGHT cursor buttons on the RC or VOL+/VOL- 
buttons on the panel to select the channels 
number. Then press DOWN cursor button 
to select SEARCH, then again press LEFT/
RIGHT cursor buttons on the RC or VOL+/VOL- 
buttons on the panel to start channel search. •  Fine tuning: press RIGHT cursor button to 
enter fine tune mode. Now press RIGHT/LEFT 
cursor buttons to adjust the frequency. •  Channel edit: press RIGHT cursor button 
on the RC to enter channel edit mode.
1 NAME  2 DELETE    3 SWAP    MENU : EXIT
001    011    021
002     012    022
003     013    023
004     014    024
005     015    025
006     016    026
007     017    027
008     018    028
009     019    029
010     020    030
•  Name: select a channel with cursor 
buttons. Press “1” number button to name; 
press UP/DOWN cursor buttons to select a 
number. Press LEFT/RIGHT cursor buttons to 
go to the next or previous digit. After selecting 
all numbers, press “1“ number button to confirm. •  Delete: select a channel with cursor 
buttons. Press “2“ number button to delete the 
selected channel. Press “1“ button to confirm. •  Swap: select a channel with cursor buttons. 
Press “3“ number button, then press UP/DOWN 
cursor button to select the new position for the 
channel. Press “1“ button to confirm.
USB operation
Insert a USB into the USB jack. Select USB 
source and press OK button. The screen will 
show a USB playback window:
1 23 4 5
1. Image file indicator
2. Storage contents list
3. Audio file indicator
4. Current file information
5. File preview window
  USB capacity supported: up to 16 Gb. 
2.0 USB version is supported. For correct and 
satisfactory operation, licensed USB devices 
of famous brands should be used with this unit. 
Avoid using USB devices of unknown brands.
File playback•  Press DOWN direction button to go to 
contents list. •  Press UP/DOWN direction buttons to se-
lect the needed file. Press RIGHT cursor button 
to play the selected file. •  Press MENU button to stop playback.
•  Press LEFT cursor button to return to 
previous menu level.
Downloaded From TV-Manual.com Manual” 
						

							10
General information
Troubleshooting
Below is a table describing simple measures that can help you eliminate most problems likely 
to emerge when this unit is in use. If below measures do not help, turn to a service center or to the 
nearest dealer.
Symptom Cause Solution
No picture, no 
sound, and no 
indicator light The power cord is not plugged in.
Contrast, brightness, color and 
volume are all in the minimum value 
or TV is in mute mode. Plug the power cord in.
Alter the value of contrast, 
brightness, color and volume.
Picture and 
sound with 
abnormity Contrast and color are set improperly.
Color system is set improperly.
Sound system is set improperly. Set the value of Contrast and color 
properly.
Set the sound system properly.
Picture is spotted 
or with snow Signal source is low-grade or the 
signal is in a lower quality. Use the qualified signal cord.
Blue background No video signal or the signal cord is 
improperly/not connected. Connect the signal cord properly.
No sound No audio signal or the signal cord is 
improperly/not connected. Connect the audio signal cord 
properly.
Set the sound system properly.
The RC does not 
work Batteries are improperly installed or 
exhausted. Make sure the positive and the 
negative polarities are correct.
Reattach the battery lid.
Replace the batteries.
Causes of interferenceIncorporated in your TV receiver are 
the most up-to-date devices to eliminate 
interference. Local radiation however, can 
create disturbances, which visibly affect your 
picture. Proper installations, a good aerial 
are your best safeguards against these 
disturbances. •  RF INTERFERENCE: Moving ripples 
across the screen are caused by nearby 
transmitting or receiving short-wave radio 
equipment. •  DIATHERMY: Herringbone pattern 
and partial picture loss can result from the 
operation of diathermy equipment from a 
nearby doctor’s surgery or hospital. •  SNOW: Weak TV signals from long 
distant stations result in an instead picture  and give the effect of falling snow. An antenna 
adjustment or antenna amplifier may be 
needed.
•  GHOST: Multiple image, caused by 
TV signals reflected back from surrounding 
buildings, hills, aircraft, etc. is minimized by 
correct aerial positioning. •  CAR IGNITION: Nearby cars and electrical 
motors can cause small streaks across the 
picture or make the picture roll.
Downloaded From TV-Manual.com Manual”