IBM Projector C400 User Manual

Chapter
 
2.
 
Setting
 
up
 
the
 
projector
 
This
 
chapter
 
provides
 
information
 
on
 
positioning
 
the
 
projector,
 
connecting
 
a
 
computer
 
source
 
and
 
displaying
 
and
 
adjusting
 
an
 
image.
 
Starting
 
the
 
projector
 
To
 
start
 
the
 
projector,
 
do
 
the
 
following:
 
1.
   
 
Connect
 
the
 
power
 
cord
 
to
 
the
 
projector
 
as
 
shown
 
below.
 
Connect
 
the
 
other
 
end
 
of
 
the
 
cord
 
to
 
an
 
electrical
 
outlet.
 
The
 
Power
 
and
 
Lamp-ready
 
LEDs...

The
 
projector
 
prepares
 
for
 
shut-down
 
and
 
the
 
Wait
 
a
 
moment
 
message
 
displays,
 
as
 
shown
 
below.
 
The
 
projector
 
turns
 
off
 
automatically
 
within
 
5
 
seconds.
    
 
Note:
 
 
This
 
operation
 
can
 
be
 
cancelled
 
by
 
pressing
 
a
 
button
 
other
 
than
 
the
 
Power
 
button.
 
Pressing
 
the
 
Power
 
button
 
again
 
will
 
turn
 
off
 
power.
 
Note:
 
 
Leave
 
the
 
power
 
cable
 
plugged
 
in
 
for
 
at
 
least
 
2-5
 
minutes
 
until
 
the
 
projector...

Figure
 
2-1.
 
Image
 
height
    
Figure
 
2-2.
 
Image
 
width
 
  
Table
 
2-1.
 
Projection
 
distance
 

1
 
(m/ft)
 
Image
 
Width
 

2
 
(m/in.)
 
Diagonal
 
image
 
size
 

3
 
(m/in.)
 
Image
 
height
 

4
 
(m/in.)
 
1.5
 
m/4.92
 
ft
 
1.1
 
m/42.5
 
in.
 
0.9
 
m/33.8
 
in.
 
0.7
 
m/25.6
 
in.
 
2.0
 
m/6.56
 
ft
 
1.4
 
m/56.7
 
in.
 
1.2
 
m/45.3
 
in.
 
0.9
 
m/34.0
 
in.
 
2.4
 
m/7.87
 
ft
 
1.7
 
m/67.7
 
in.
 
1.4
 
m/53.9
 
in.
 
1.0
 
m/40.5
 
in.
 
2.8
 
m/9.18
 
ft
 
2.0...

Adjusting
 
the
 
projector
 
level
 
and
 
height
 
To
 
adjust
 
the
 
projector
 
level
 
and
 
height,
 
complete
 
the
 
following
 
procedure:
 
1.
   
 
To
 
raise
 
the
 
height
 
of
 
the
 
projector,
 
lift
 
the
 
projector
 

1and
 
press
 
the
 
height-adjuster
 
buttons
 

2.
 
The
 
elevator
 
foot
 

3drops
 
down.
 
2.
 
 
 
To
 
make
 
minor
 
adjustments
 
to
 
the
 
height,
 
rotate
 
the
 
elevator
 
foot
4
 
as
 
shown
 
below.
 
3.
 
 
 
To
 
lower
 
the
 
level
 
of
 
the...

1.
   
 
Twist
 
the
 
rings
 
on
 
the
 
projector
 
to
 
adjust
 
the
 
focus
 

1
 
and
 
zoom
 

2,
 
as
 
shown
 
below.
  
 
 
 
2.
 
 
 
Use
 
the
 
Keystone
 
buttons
 
on
 
the
 
projector
 
or
 
the
 
remote
 
to
 
correct
 
image-trapezoid
 
(wider
 
top
 
or
 
bottom)
 
effect.
 
The
 
Keystone
 
buttons
 
on
 
the
 
remote
 
and
 
projector
 
are
 
shown
 
below.
  
 
 
The
 
keystone
 
control
 
appears
 
on
 
the
 
On
 
Screen
 
Display
 
(OSD),
 
as
 
shown.
  
 
 
Adjusting
 
the...

2.
   
 
Use
 
the
 
Volume
 
+/-
 
buttons
 
shown
 
below
 
to
 
adjust
 
the
 
level.
  
 
 
 
3.
 
 
 
Press
 
the
 
Mute
 
button
 
(on
 
the
 
remote
 
control
 
only)
 
to
 
turn
 
off
 
the
 
volume.
 
4.
 
 
 
Press
 
any
 
Volume
 
+/-
 
buttons
 
on
 
the
 
projector
 
or
 
remote
 
control
 
to
 
turn
 
off
 
mute.
  
2-6
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 

Chapter
 
3.
 
Connecting
 
devices
 
to
 
the
 
projector
 
This
 
chapter
 
provides
 
information
 
on
 
connecting
 
devices
 
to
 
the
 
C400
 
projector.
 
Connecting
 
devices
 
Computers
 
and
 
video
 
devices
 
can
 
be
 
connected
 
to
 
the
 
projector
 
at
 
the
 
same
 
time.
 
Refer
 
to
 
the
 
documentation
 
that
 
comes
 
with
 
the
 
connecting
 
device
 
to
 
verify
 
that
 
the
 
device
 
has
 
the
 
appropriate
 
output
 
connector.
    
 
 

1
 
Local
 
Area
 
Network
 
RJ-45...

Connecting
 
to
 
a
 
USB
 
device
 
To
 
control
 
your
 
computer
 
mouse
 
using
 
the
 
projector
 
remote
 
control,
 
connect
 
the
 
projector
 
to
 
the
 
computer
 
with
 
a
 
USB
 
cable
 
as
 
shown
 
below.
    
 
Note:
 
 
USB
 
mouse
 
function
 
is
 
only
 
supported
 
with
 
Windows
 
2000
 
and
 
Windows
 
XP.
 
Connecting
 
to
 
a
 
computer
 
monitor
 
If
 
you
 
are
 
using
 
a
 
desktop
 
computer
 
and
 
want
 
to
 
see
 
the
 
image
 
on
 
your
 
computer
 
screen
 
as
 
well
 
as...

Chapter
 
4.
 
Using
 
the
 
projector
 
features
 
This
 
chapter
 
provides
 
information
 
on
 
installing
 
the
 
remote
 
control
 
batteries
 
and
 
on
 
using
 
the
 
remote
 
control,
 
audio,
 
keypad
 
buttons,
 
and
 
other
 
projector
 
features.
 
Before
 
you
 
begin
 
Before
 
you
 
can
 
use
 
the
 
remote
 
control,
 
you
 
must
 
install
 
the
 
AAA
 
batteries
 
that
 
come
 
with
 
this
 
projector.
 
To
 
install
 
the
 
batteries,
 
do
 
the
 
following:
 
Note:
   
v
 
 
 
Use...

3.
   
 
Replace
 
the
 
cover,
 
as
 
shown.
  
 
 
Using
 
the
 
remote
 
control
 
The
 
figure
 
below
 
provides
 
an
 
illustration
 
of
 
the
 
remote.
  
 
 
CAUTION:
 
To
 
reduce
 
the
 
risk
 
of
 
injury
 
to
 
the
 
eyes,
 
do
 
not
 
look
 
directly
 
into
 
the
 
remote
 
control
 
laser
 
light
 
and
 
do
 
not
 
point
 
the
 
laser
 
light
 
into
 
anyone’s
 
eyes.
 
The
 
remote
 
control
 
is
 
equipped
 
with
 
a
 
Class
 
II
 
laser
 
that
 
emits
 
radiation.
 

1
 
Laser
  
 

2...