Iiyama Prolite E2202ws B1 User Manual

							ENGLISH
CONTROLS AND CONNECTORS : ProLite E2201W
 
APower Switch (     )
BMenu Button (MENU)
C+ Button ( + )
D– Button ( – )
EAuto Button (AUTO)
FInput Button (SOURCE)
GPower Indicator
Blue:Normal operation
Orange:Power Management
„Auto (Signal Select)
When no signal is received from the system, the display enters into its
Power Management Mode reducing power consumption to < than 2W.
„Analog / Digital (Signal Select)
The monitor enters into power management mode which reduces the power
consumption to less than 2W when receiving no horizontal and/or vertical
sync signal.
HD-sub mini 15pin Connector (D-SUB)
IDVI-D 24pin Connector (DVI-D)
JKeyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
KAC Connector (AC IN)
NOTE
NOTE
BEFORE YOU OPERATE THE MONITOR     7
 
						

							ENGLISH
8     BEFORE YOU OPERATE THE MONITOR
CONTROLS AND CONNECTORS : ProLite E2202WS / E2202WSV
APower Switch (     )
BMenu Button (MENU)
C+ Button (               )
D– Button (               )
EAuto Button (AUTO)
FInput Button (SOURCE)*
GPower Indicator
Blue:Normal operation
Orange:Power Management
„Auto (Signal Select)
When no signal is received from the system, the display enters into its
Power Management Mode reducing power consumption to < than 2W.
„Analog / Digital (Signal Select)
The monitor enters into power management mode which reduces the power
consumption to less than 2W when receiving no horizontal and/or vertical
sync signal.
HSpeakers
IAC Connector (AC IN)
JAudio Connector (             )
KDVI-D 24pin Connector (DVI-D)*
LD-sub mini 15pin Connector (D-SUB)
MKeyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission. 
NOTE
NOTE
*Available for ProLite E2202WS only.
 
						

							ENGLISH
Computer D-Sub Signal Cable
(Accessory)
DVI-D Signal Cable 
(Accessory) Power Cable
(Accessory)
CONNECTING YOUR MONITOR : ProLite E2201W
[Example of Connection] AEnsure that both the computer and the monitor are switched off.
BConnect the computer to the monitor with the signal cable. (See page 32 for CONNECTOR PIN
ASSIGNMENT.)
CConnect the Power Cable to the monitor first and then to the power supply.
NOTE„The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector.
If a special cable is required please contact your local iiyama dealer or regional iiyama office.
„For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
„Make sure you tighten the finger screws at each end of the signal cable.

[ Fitting of Cable Holder ]
ACollect cables at the back of the stand.
BPosition the Cable Holder at the base of the
stand column by inserting the ‘tabs’ into the
guide holes.  Apply gentle pressure downwards
to secure.
[ Removal of Cable Holder ]
ARemove Cable Holder by sliding up the base
column.
Ãáâìå Èïìäåò
Stand
BEFORE YOU OPERATE THE MONITOR     9
 
						

							ENGLISH
10     BEFORE YOU OPERATE THE MONITOR
Audio Cable (Accessory)
Computer D-Sub Signal Cable
(Accessory)
DVI-D Signal Cable* Power Cable
(Accessory)
CONNECTING YOUR MONITOR : ProLite E2202WS / E2202WSV
[Example of Connection] AEnsure that both the computer and the monitor are switched off.
BConnect the computer to the monitor with the signal cable. (See page 32 for CONNECTOR PIN
ASSIGNMENT.)
CConnect the monitor to the audio equipment with the Audio Cable when using the audio features.
DConnect the Power Cable to the monitor first and then to the power supply.
NOTE„The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector.
If a special cable is required please contact your local iiyama dealer or regional iiyama office.
„For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
„Make sure you tighten the finger screws at each end of the signal cable.

*Available for ProLite E2202WS only.
[ Fitting of Cable Holder ]
ACollect cables at the back of the stand.
BPosition the Cable Holder at the base of the
stand column by inserting the ‘tabs’ into the
guide holes.  Apply gentle pressure downwards
to secure.
[ Removal of Cable Holder ]
ARemove Cable Holder by sliding up the base
column.
Ãáâìå Èïìäåò
Stand
 
						

							ENGLISH
20
5
ADJUSTING THE VIEWING ANGLE
„For optimal viewing it is recommended to look at the full face
of the monitor.
„Hold the stand so that the monitor does not topple when you
change the monitor’s angle.
„You are able to adjust the monitor’s angle up to 20 degrees
upward, 5 degrees downward.
„In order to ensure a healthy and relaxed body position when
using the monitor at visual display workstations, it is
recommended that the adjusted tilt angle should not exceed
10 degrees. Adjust the monitor’s angle to your own preference.
NOTE„Do not touch the LCD screen when you change the
angle. It may cause damage or break the LCD screen.
„Careful attention is required not to catch your fingers
or hands when you change the angle.
NOTE
COMPUTER SETTING
„Signal Timing
Change to the desired signal timing listed on page 31: COMPLIANT TIMING.
„Windows 95/98/2000/Me/XP/Vista Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on
Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with
the Signal Cable supplied. Windows 95/98/2000/Me/XP/Vista Monitor Information File for iiyama
monitors may be necessary for your computer and obtained via the Internet, using the address:
http://www.iiyama.com
„For additional information on how to download the driver for your monitor, please
access one of the internet sites noted above.
„Monitor Drivers are not required in most cases for Macintosh or Unix operating systems.
For further information, please contact your computer dealer first for advice.
BEFORE YOU OPERATE THE MONITOR     11
 
						

							ENGLISH
12     OPERATING THE MONITOR
The bar shows 
the progress of the 
adjustment being made.+
–50
V-Position
Menu:1
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 31. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 21 for SCREEN ADJUSTMENTS.
( (( (
(Press the Menu Button to start the On Screen Display feature. There are
additional Menu pages which can be switched by using the +/– Buttons.
B BB B
BSelect the Menu page which contains the adjustment icon relating to the
adjustment you want to make. Press the Menu Button again. Then, use the
+/– Buttons to highlight the desired adjustment icon. Press the Menu Button
again.
When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the OSD Off Timer has passed. The Auto Button can be used to exit OSD window
immediately. „NOTEAn adjustment scale appears after you press the Menu Button. Use the +/– Buttons to change the
vertical position settings. The vertical position of the overall display should be changing accordingly
while you are doing this.
C CC C
CUse the +/– Buttons to make the appropriate adjustment or setting.
Adjustments for Clock, Phase and Position are saved for each signal timing. Except for these
adjustments, all other adjustments have only one setting which applies to all signal timings. „For example, to correct for vertical position, select Menu page number 1 and then press the Menu
Button. Then, select        (V-Position) by using the +/– Buttons.
Any changes are automatically saved in the memory when the On Screen Display 
disappears.
Turning off the power should be avoided while using the Menu.„
Adjustment icon
Current horizontal frequency,
vertical refresh rate
and resolution
1680 × 1050
H:65.4KHz  V:60.1Hz
Menu:1Page no. Displayed while Economy Mode is active.Displayed while sRGB is active.Displayed while Mute is active.Displayed while Lock Out is active.LOCK1sRGBDCROFF
DCR setting is displayed.
 
						

							ENGLISH
ADJUSTMENT MENU CONTENTS
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
zBrightness / Contrast / Volume*
1 / DCR: To display direct menu press either of the +/- Buttons.
Continue to use the +/- Buttons to select the adjustments
required.
z  DCR: Select on the Direct Menu.
Off: Typical Contrast Ratio
On: Increased Contrast Ratio
DCR adjusts brightness according to the image, and improve the contrast ratio
up to 2000:1 during move playing.
Brightness, sRGB and Economy Mode cannot be adjusted and selected while
DCR is active.
z  Auto Set-up: Press the Auto Button when the Menu is not displayed.
z  Volume (Mute)*
1: With the OSD menu off, the pressing and holding of the Menu Button for 1-2
seconds will enable/disable the Audio Mute facility.
z  Signal Select*
2: With the OSD menu off, pressing the Input Button will switch the input signal
from Analogue to Digital.
z  Lock Out:With the OSD menu off, pressing and holding the Menu and ‘-‘ Buttons
simultaneously for a period of at least 7 seconds will enable and disable the OSD
Lock Out mode.
       is displayed while Lock Out is active.
Direct
DCR
*1Available for ProLite E2202WS / E2202WSV only.
OPERATING THE MONITOR     13
*2Available for ProLite E2201W / E2202WS only.
NOTE
 
						

							ENGLISH
14     OPERATING THE MONITOR
Menu:1
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
Adjustment Item Problem / Option                       Button to Press
Too dark
Too brightBrightness *1
ContrastToo dull
Too intense
To correct flickering text or linesClock *2
Phase *2
H-PositionToo far to the left
Too far to the right
V-PositionToo low
Too high
Return to MenuHighlight “Menu : 1” again.
To correct flickering text or lines
Direct
Direct
*1Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
*
2See page 21 for SCREEN ADJUSTMENTS.
Menu : 1
(Analog) Analog Input
See page 13 for Direct adjustment.Direct
 
						

							ENGLISH
Menu:2
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFFMenu : 2
(Analog)
On
Problem / Option                                                  Button to Press Adjustment Item
Color Temp.
Color 1: 9300K
Sharpness1 2 3 4 5
Adjust the picture quality at resolutions of less than 1680 ×
1050.
You can change the picture quality from 1 to 5 (sharp to soft).
Press the + Button to change the picture quality in numerical
order. Press the – Button to change the picture quality in reverse
numerical order. Auto Set-up *
3NO
YESReturn to Menu.
Adjust Clock, Phase, V-Position and H-Position
automatically.
Direct
*3For best results, use the Auto Set-up in conjunction with the adjustment pattern. See page 21 for
SCREEN ADJUSTMENTS.
1
NOTE„sRGB is an international standard which defines and unifies the difference of color
appearance between equipment.
„You can not adjust the Brightness, Contrast, Gamma and Economy Mode during sRGB
mode because those settings are locked.
„        is displayed while sRGB is active.
3Color 3: 6500K Color 2: 7500K
sRGB
Setting
The Auto Set-up is not performed when the
signal input is changed.Off
Adjust Clock, Phase, V-Position and H-Position
automatically when the signal input is changed.
GR
BToo weak
Too strong s
NOTE„The brightness of screen varies for several seconds during the adjustment.
„This function is not performed automatically when changing the signal input because
the factory-preset of “Setting” in Auto Set-up is set to Off.
(User)
2
See page 13 for Direct adjustment.
Direct
OPERATING THE MONITOR     15
 
						

							ENGLISH
16     OPERATING THE MONITOR
Normal
Menu : 2
(Analog)
Return to MenuHighlight “Menu : 2” again.
Off
Mode1High contrast
Dark
Gamma
Mode1Brightness of back-light is reduced.
Mode2Brightness of back-light is reduced more than Mode1.
Economy ModeOffNormal
Mode2
Problem / Option Adjustment Item
NOTE„       is displayed while Economy Mode is active.