Indesit Ban 12 X Operating Instructions

							

REFRIGERATOR/FREEZER COMBINATION



	

Positioning and connection
Reversible doors





	

Overall view


	




	

Starting the appliance
Chiller system
Using the refrigerator to its full potential
Using the freezer to its full potential




	

Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Defrosting the appliance
Replacing the light bulb



	

General safety
Disposal
Respecting and conserving the environment
 !
	
#$

	
##

	


%&
#
&



(%
 
						

							





Before placing your new appliance into operation please
read these operating instructions carefully. They contain
important information for safe use, for installation and for
care of the appliance.

Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.




	
	
1. Place the appliance in a well-ventilated humidity-free
room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of
the appliance and any furniture above it, and at least 5
cm between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat
(direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied
in the installation kit, following the instructions provided.


1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the
refrigerator by tightening or loosening the front feet.


	
	
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to
the electricity mains. Before inserting the plug into the
electrical socket ensure the following:
• The appliance is earthed and the plug is compliant with
the law.
 The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on
the bottom left side of the fridge (e.g. 150 W).
 The voltage must be in the range between the values
indicated on the data plate located on the bottom left
side (e.g. 220-240V).
 The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it (
see Assistance). Do
not use extension cords or multiple sockets.

Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.

The cable must not be bent or compressed.

The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).

The manufacturer declines any liability should these
safety measures not be observed.
Connection of the water supply
To carry this out, use the kit provided which contains all the
necessary elements for connection to the water supply.
To improve the performance of the Aqua Care, we
recommend that you fit a tap with a filter on the pipe for
the connection to the water system: in this way it will be
possible to manually interrupt the water supply during
long periods in which Aqua Care is not used.

 The water pressure inside the water system must be
between 0.8 bar and 8 bar.

 The appliance must only be connected to a water
supply suitable for drinking.
Your appliance is supplied with a 13amp fused plug that
can be plugged into a 13amp socket for immediate use.
Before using the appliance please read the instructions
below.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
Replacing fuse covers:
When replacing a faulty fuse, a 13amp ASTA approved
fuse to BS 1362 should always be used and the fuse
cover re-fitted.
If the fuse cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking or the
colour that is embossed in words on the base of the plug.
Changing the plug:
Removing the plug
If your appliance has a non-rewireable moulded plug
and you should wish to remove it to add a longer cable
or to re-route the mains cable through partitions, units
etc. please ensure that either:
- The plug is replaced by a fused 13amp re-
wireable plug bearing the BSI mark of approval.
or
- The mains cable is wired directly into a 13amp
cable outlet, controlled by a switch (in compliance
with BS 5733) which is accessible without moving
the appliance.
Disposing of the plug
Cut off and dispose of the supplied plug if it does not fit
your socket. The cable should be cut as close as
possible to the moulded plug.
Remove the fuse.
 
						

							


)
*
!






∅ 3mm
WARNING:
To avoid a shock hazard do not insert the discarded
plug into a socket anywhere else.
Fitting a new plug
IMPORTANT:
WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...
Green and Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- Connect Green and Yellow wire to terminal marked
E or 
  or coloured Green and Yellow.
- Connect Brown wire to terminal marked L or
coloured red or brown.
- Connect Blue wire to terminal marked N  or
coloured Black or Blue.
If a 13amp plug (BS 1363) is used it must be
fitted with a 13amp fuse.
If you are in any doubt about the electrical
supply to your machine, consult a qualified
electrician before use.
CE Marking certifies that this appliance conforms to
the following EEC directives :
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC
& 93/68/EEC
 
						

							






+*

*
,
The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not directly
represent the appliance purchased. For more complex features, consult the following pages.

 Varies by number and/or position.

 Available only on certain models. Levelling FEET
Removable lidded
shelf with 

Removable
multipurpose
SHELVES

shelf

ice tray• 



 
Knob

ice tray


!
and


compartment


compartment


!


 
Knob
#
 (
see Maintenance)
#$%$


bin
FRUIT and
&



  
bin
 
						

							




&
: with or without grill.
Due to the special guides the
shelves are removable and the
height is adjustable (
see
diagram
), allowing easy storage
of large containers and food.
Height can be adjusted without
complete removal of the shelf.
#$%$


bin: to store food (such as cold meats)
for a long time and also prevent odours from lingering
in the refrigerator.

#
$


Indicator light: to identify the coldest
area in the refrigerator.
1. Check that OK appears clearly on the indicator light
(
see diagram).
vertnoir
consulter la notice
2. If the word “OK” does not appear it means that the
temperature is too high: adjust the REFRIGERATOR
OPERATION knob to a higher (colder) position and
wait approximately 10 hours until the temperature has
stabilised.
3. Check the indicator light again: if necessary, readjust
it following the initial process. If large quantities of
food have been added or if the refrigerator door has
been opened frequently, it is normal for the indicator
not to show OK. Wait at least 10 hours before
adjusting the REFRIGERATOR OPERATION knob to a
higher setting.

 Available only on certain models.
1
2
 
						

							










()	


**+)		,


	

-
	 (
see Installation).
(Before connecting the appliance, clean the
compartments and accessories well with lukewarm
water and bicarbonate.
(The appliance comes with a motor protection control
system which makes the compressor start approximately
8 minutes after being switched on. The compressor also
starts each time the power supply is cut off whether
voluntarily or involuntarily (blackout).
1. Insert the plug into the socket and ensure that the
internal light illuminates ( the FREEZER OPERATION
knob must not be on the 

position)  .
2. Turn the FREEZER OPERATION knob and
REFRIGERATOR OPERATION knob to an average
value. After a few hours you will be able to put food in
the refrigerator.




-

The temperature inside the
refrigerator compartment
automatically adjusts itself
according to the position
of the thermostat knob.
min= warmest
max = coldest
We recommend, however,
a medium position.
.

/
-
 		

It is recognisable by
aeration cells located on
the back walls of the
compartments.
The No Frost system
circulates cold air
continuously to collect
humidity and prevent ice
and frost formation. The
system maintains an
optimal humidity level in
the compartment,
preserving the original quality of the food, preventing the
food from sticking together and making defrosting a thing
of the past. Do not block the aeration cells by placing
food or containers in direct contact with the refrigerating
back panel. Close bottles and wrap food tightly.
0









 Place only cold or lukewarm foods in the compartment,
not hot foods (
see Precautions and tips).
 Remember that cooked foods do not last longer than
raw foods.
 Do not store liquids in open containers. They will
increase humidity in the refrigerator and cause
condensation to form.
		./
1.  Once you have bought your food, remove all external
packaging made of paper/cardboard or other
wrappers, which could introduce bacteria or dirt
inside your refrigerator.
2.  Protect the food, (especially easily perishable items
and those that have a strong smell), in order to avoid
contact between them, thereby removing both the
possibility of germ/bacteria contamination as well as
the diffusion of strong odours inside the fridge.
3.  Store all food in such a way as to ensure air can
circulate freely between different items.
4.  Keep the inside of your fridge clean, taking care not
to use oxidiser or abrasive products.
5.  Remove all food past its expiry date from the
refrigerator.
6.  For the correct preservation of food, all easily
perishable items (soft cheeses, raw fish, meat, etc.)
should be stored in the coldest zone of the fridge
compartment, i.e. just above the salad crisper where
the temperature indicator is situated.
 
						

							


0



1






The temperature inside the
freezer compartment
automatically adjusts itself
according to the position of
the thermostat knob.
= warmest
 = coldest
We recommend, however, a
medium position.

0 is the optimal temperature for energy saving levels.
 switches the appliance off, including the refrigerator.
 Do not re-freeze food that is defrosting or that has
already been defrosted. These foods must be cooked
and eaten (within 24 hours).
 Fresh food that needs to be frozen must not come into
contact with food that has already been defrosted.
Fresh food must be stored in the top FREEZER and
STORAGE compartment where the temperature drops
below -18°C and guarantees rapid freezing.
 Do not place glass bottles which contain liquids, and
which are corked or hermetically sealed in the freezer
because they could break.
 The maximum quantity of food that may be frozen daily
is indicated on the plate containing the technical
properties located on the bottom left side of the
refrigerator compartment (for example: Kg/24h: 4)

Do not open the door during freezing.

If there is a power cut or malfunction, do not open the
freezer door. This will help maintain the temperature
inside the freezer, ensuring that foods are conserved for
at least 9 -14 hours.

To avoid blocking the air circulation inside the freezer
compartment, it is advisable not to obstruct the
ventilation holes with food or containers.
WATER LEVELMAX
WATER LEVELMAX
WATER LEVELMAX


/
The fact that they are situated on the top part of the freezer
drawers ensures greater cleanliness: the ice no longer comes
into contact with the food placed inside the freezer
compartment; furthermore, the dripping of the water during
filling is avoided (a lid to cover up the hole after filling with
water is also provided).
1. Pull out the tray by pushing it up.
Check that the tray is ompletely empty and fill it with
water through the opening provided.
2. Take care not to exceed the level indicated (MAX
WATER LEVEL). Excess water prevents the ice cubes
from dispensing (if this happens, wait for the ice to
melt and empty the tray).
3. Turn the tray 90°: due to the connected compartments
each mould fills with water (
see diagram).
4. Close the opening with the lid provided and put the
tray back, placing the top part in the corresponding
housing and allowing it to drop in again.
5. When the ice has formed (minimum time
approximately 8 hours) knock the tray against a hard
surface and wet the outside so that the ice cubes
come loose and take them out through the opening.
 
						

							





,



During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply:
1. set the FREEZER OPERATION knob on 
2. pull the plug out of the socket
.



 The external and internal parts, as well as the rubber
seals may be cleaned using a sponge that has been
soaked in lukewarm water and bicarbonate of soda or
neutral soap. Do not use solvents, abrasive products,
bleach or ammonia.
 The removable accessories may be soaked in warm
water and soap or dishwashing liquid. Rinse and dry
them carefully.
 The back of the appliance may collect dust which can
be removed by delicately using the hose of a vacuum
cleaner set on medium power. The appliance must be
switched off and the plug must be pulled out before
cleaning the appliance.
*
-




 The appliance is manufactured with hygienic materials
which are odour free. In order to maintain an odour free
refrigerator and to prevent the formation of stains, food
must always be covered or sealed properly.
 If you want to switch the appliance off for an extended
period of time, clean the inside and leave the doors
open.*

1-1
To replace the light bulb in the refrigerator compartment,
pull out the plug from the electrical socket. Follow the
instructions below.
Access the light bulb by removing the cover as
indicated in the diagram.
Replace it with a similar light bulb within the power
range indicated on the cover (10W).
 
						

							

	





The appliance was designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
This appliance complies with the following
Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC of 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE.
(



/
 The appliance was designed for domestic use inside
the home and is not intended for commercial or
industrial use.
 The appliance must be used to store and freeze food
products by adults only and according to the
instructions in this manual.
 The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
 Do not touch the appliance with bare feet or with wet or
moist hands and feet.
 Do not touch the internal cooling elements: this could
cause skin abrasions or frost/freezer burns.
 When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
 Before cleaning and maintenance, always switch off
the appliance and disconnect it from the electrical
supply. It is not sufficient to set the temperature
adjustment knobs on 
 (appliance off) to eliminate all
electrical contact.
 In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
 Do not use devices or tools other than the special
scraper provided inside the compartments.
 Do not put ice cubes taken directly from the freezer
into your mouth.
 Do not allow children to tamper with the controls or
play with the appliance. Under no circumstance should
they be allowed to sit on the bins or to hang from the
door.
 Keep packaging material out of the reach of children! It
can become a choking or suffocation hazard.

 Observe local environmental standards when
disposing packaging material for recycling purposes.
 The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the
appliance it must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
)




*


*-

 Install the appliance in a fresh and well-ventilated
room. Ensure that it is protected from direct sunlight
and do not place it near heat sources.
 Try to avoid keeping the door open for long periods or
opening the door too frequently in order to conserve
energy.
 Do not fill the appliance with too much food:
cold air must circulate freely for food to be preserved
properly. If circulation is impeded, the compressor will
work continuously.
 Do not place hot food directly into the refrigerator. The
internal temperature will increase and force the
compressor to work harder and will consume more
energy.
 Defrost the appliance if ice forms (
see Maintenance).
A thick layer of ice makes cold transference to food
products more difficult and results in increased
energy consumption.
 Regularly check the door seals and wipe clean to
ensure they are free of debris and to prevent cold air
from escaping (
see Maintenance).
 
						

							




	
If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.
2


.		

-2
3
2	
	.		


3
)
	.
)4.	
	
		,3
)		..
)
	
1
	)43
2	
	-	
-	-/3
**25	
	)	3
	2	)
6
*
	)

)
	1	2	

!


3
2
 The plug has not been inserted into the electrical socket, or not far
enough to make contact, or there is no power in the house.
 The appliance comes with a motor protection control (
see Start-up and use).
 The doors do not close properly or the seals are damaged.
 The doors are opened too frequently.
 The TEMPERATURE ADJUSTMENT knob is not in the correct position
 The refrigerator or the freezer have been over-filled.
 The TEMPERATURE ADJUSTMENT knob is not in the correct position.
 The door is not closed properly or is continuously opened.
 The outside ambient temperature is very high.
 The appliance has not been installed on a level surface (
see Installation).
 The appliance has been installed between cabinets that vibrate and
make noise.
 The internal refrigerant makes a slight noise even when the compressor is
off. This is not a defect, it is normal.
 These raised temperatures are necessary in order to avoid the formation
of condensation on certain parts of the product.