Home > Indesit > Dishwasher > Indesit Di 450 Installation Manual

Indesit Di 450 Installation Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Indesit Di 450 Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 260 Indesit manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							9EN
    Troubleshooting
    It may occur that the dishwasher does not function or does
    not function properly. Before calling for assistance, let us
    see what can be done first: have you forgot to press one of
    the buttons or to perform an essential operation?
    The Dishwasher Does Not Start
    Have you checked whether:
    - the plug is pushed into the socket correctly;
    - the power is on in the house;
    - the door is closed properly;
    - the ON-OFF switch is on ON;
    - the water supply is turned on.
    The Dishwasher Does Not Load Water
    Have you checked whether:
    - the water is turned on and the hose is connected properly;
    - the water supply to the house is on and has sufficient
      pressure;
    - the water supply hose is crimped or bent;
    - the filter for the water supply hose is clogged.
    The Dishes Are Not Clean
    Have you put the right amount of detergent into the
    dispenser?
    Is the wash cycle suitable for the dishes you have placed
    inside the appliance?
    Are the filter and microfilter clean?
    Can the sprayer arms turn freely?
    The Dishwasher Does Not Drain
    Have you checked whether:
    - the drain hose is crimped or bent.
    Lime Deposits or a White Film Form on the Dishes
    Have you checked whether:
    - the lid to the salt container is closed properly;
    - the rinse aid dosage is correct.
    Error messages.
    Your dishwasher is equipped with a safety system which is able to
    detect any operating anomalies. These anomalies are reported by
    one or two wash cycle indicator lights G flashing rapidly.
    Take a note of which lights are flashing, turn the appliance off and
    call for technical assistance.Tap off alarm
    If you have forgotten to turn the water tap on, your appliance will
    remind you of this by sounding a few short beeps for a few minutes.
    Turn the tap on and your appliance will start up again after a few
    minutes. Were you to be absent when these beeps are sounded, the
    appliance will be blocked automatically and indicator lights 3 and 4
    Eco and Rapid) will flash rapidly. Turn the appliance off at the ON-
    OFF button, turn on the water tap and wait approximately 20
    seconds before turning the appliance back on; repeat the
    programming operations and the selected wash cycle will start up
    again.
    Clogged filter alarm
    If the appliance is blocked and indicator lights 2 normal) and 4
    (Rapid) flash rapidly, this means the filter is clogged by large particles
    of food residue. Turn the appliance off, clean the filter thoroughly
    and reposition it in its seat as illustrated on this page. Then turn it
    back on. Repeat the programming operations and the selected wash
    cycle will start up again.
    Water load solenoid valve malfunction alarm.If indicator light 3  (Eco) flashes rapidly, TURN the dishwasher OFF
    AND BACK ON AGAIN after one minute. If the alarm persists, first
    turn off the water tap to avoid any flooding and then cut off the
    electricity supply and call for technical assistance.
    If, despite all these checks, the dishwasher still does not
    function and/or the problem persists, contact the nearest
    authorised service centre and provide them with the
    following information:
    - the nature of the problem;
    - the model type number (Mod. ...) and the serial number
    (S/N ....), which are indicated on the plate located on the
    side of the inner part of the door.
    Never call on unauthorised technicians and refuse to
    allow parts to be installed that are not original spare
    parts.
    Cleaning and Special Maintenance
    Cleaning the Sprayer Arms
    It may happen that food particles become encrusted on the
    sprayer arms and block the holes. Check the sprayer arms
    periodically and clean them when needed (see “Close-up
    View [interior]”, letters F-I).
    1
    2
    AB
    C
    The filter assembly
    If you want consistent good results from your dishwasher,
    you need to clean the filter assembly.
    The food particles are removed from the wash water,
    allowing it to be recirculated during the cycle, filtered
    perfectly. For this reason, it is
    a good idea to remove the
    larger food particles trapped
    inside the cup “C” and the
    semi-circular filter A after each
    wash; pull the cup handle
    upwards to remove them. Just
    rinse them under running
    water.
    The entire filter assembly should be cleaned thoroughly once
    a month: cup C + semi-circular filter A + cylindrical filter B.
    Rotate filter “B” anticlockwise to remove it.
    For cleaning, use a non metallic brush.Reassemble the filter parts (as shown in the figure) and
    reinsert the whole assembly into the dishwasher. Position it
    into its housing and press downwards.
    The dishwasher is not to be used without filters. Improper
    replacement of the filters may reduce the efficiency of the
    wash and even damage your dishwasher.
     
    						
    							10EN
    Installation
    Positioning the Appliance
    Position the appliance in the desired location. The back
    should rest against the wall behind it, and the sides, along
    the adjacent cabinets or wall. The dishwasher is equipped
    with water supply and drain hoses that can be positioned to
    the right or the left to facilitate proper installation.
    Levelling the Appliance
    Once the appliance is positioned, adjust the feet (screwing
    them in or out) to adjust the height of the dishwasher, making
    it level. In any case, the appliance should not be inclined
    more than 2°.
    If the appliance is level, it will help ensure proper perfor-
    mance.
    Cold Water Connection
    This electric household appliance should be connected to
    the water mains using the cold water supply hose provided
    with the appliance only. Do not use a different hose. In the
    event of replacements, use original spare parts only.
    Connect the cold water supply hose to a threaded 3/4 (gas)
    connector, and making sure that it is fastened tightly in place.
    If the water pipes are new or have not been used for an
    extended period of time, let the water run to make sure that
    the water is clear and free of impurities. If this precaution is
    not taken, there is a risk that the water inlet can get blocked
    and damage the appliance.
    Hot Water Connection
    The water supply to the appliance can also be connected to
    the houses hot water line (centralised system, heating
    system), as long as it does not exceed a temperature of
    60°C.
    In this case, the wash cycle time will be shortened by about
    15 minutes and the wash efficiency slightly reduced.
    The connection must be made to the hot water line following
    the same procedures as those for the connection to the cold
    water line.Drain Hose Connection
    Fit the drain pipe into a drain
    line with a minimum diameter
    of 4 cm or place it over the
    sink. Avoid restricting or
    bending it.  The part of the pipe
    marked with the letter A
    should be between 40 and 100
    cm above the ground.
    The pipe should not be
    immersed in water.
    Electrical Connection
    After making sure that the voltage and frequency values for
    the current in the home correspond to those on the rating
    plate (located on the stainless steel inner door of the
    appliance) and that the electrical system is sized for the
    maximum voltage on the rating plate, insert the plug into
    an electrical socket which is earthed properly (the earthing
    of the appliance is a safety requirement mandated by law).
    If the electrical socket to which the appliance must be
    connected is not appropriate for the plug, replace the plug,
    rather than using adpators or the like as they could cause
    overheating and burns.
    Caution: the dishwasher plug must be accessible  even when
    the appliance is installed as a built-in unit so that maintenance
    can be done safely.
    Should the electricity supply cable be damaged, we
    recommend that you only contact authorised Technical Service
    Centres for the replacement.
    Condensation-proof tape.
    On some models, a transparent condensation-proof adhesive
    tape has been provided.
    It should be stuck onto the lower side of your wooden worktop
    to protect it from the formation of condensation.
    When not provided, this tape can be requested as a spare
    part from authorised retailers.
    A
     
    						
    							11EN
    Electrical Connection
    Electrical Connection
    If your appliance is supplied with a 13 amp. fused plug it
    can be plugged into a 13 amp socket for immediate use.
    Before using the appliance please read the instruction below.
    WARNING: THIS APPLIANCE MUST BE EARTHED.
    THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT
    BY A QUALIFIED ELECTRICIAN.
    Replacing the fuse:
    When replacing a faulty fuse, a 13 amp ASTA approved
    fuse to BS 1362 should always be used, and the fuse cover
    re-fitted. If the fuse cover is lost, the plug must not be used
    until a replacement is obtained.
    Replacemente fuse covers:
    If a replacement fuse cover is fitted, it must be of the correct
    colours as indicated by the coloured marking or the colour
    that is embossed in words on the base of the plug.
    Replacements can be obtained directly from your nearest
    Service Depot.
    Removing the plug:
    Ifyour appliance has a non-rewireable moulded plug and
    you should wish to remove it to re-route the mains cable
    through partitions, units etc., please esure that either:
    - the plug is replaced by a fused 13 amp re-wireable plug
      bearing the BSI mark of approval
    - or:
    - the mains cable is wired directly into a 13 amp cable outlet,
      controlled by a switch, (in compliance with BS 5733) which
      is accessible without moving the appliance.
    Disposing of the plug:
    Ensure that before disposing of the plug itself, you make
    the pins unusable so that it cannot be accidentally inserted
    into a socket.
    Instruction for connecting cable to an altenative plug:
    Important: the wires in the mains lead are coloured in
    accordance with the following code:
    Green & Yellow - Earth
    Blue - Neutral
    Brown - Live
    CAUTION:
    The dishwasher plug must be accessible even when the
    appliance is installed as a built-in unit so that maintenance
    can be done safely.As the colours of the wires in the mains lead may not
    correspond with the coloured markings identifying the
    terminal in your plug, proceed as follows:
    connect Green & Yellow wire to terminal market “E” or
    coloured Green or Green & Yellow.
    Connect Brown wire to terminal marked “L” or coloured
    Red.
    Connect Blue wire to terminal marked “N” or coloured
    Black.
    If a 13 amp plug (BS 1363) is used it must be fitted with a
    13 amp fuse. A15 amp plug must be protected by a 15
    amp  fuse, either in the plug or adaptor or at the
    distribution board.
    If you are in any doubt about the electrical supply to your
    machine, consult a qualified electrician before use.
    How to connect an alternative plug:
    The wires in this mains lead are coloured in accordance
    with the following code:
    BLUE“NEUTRAL” (“N”)
    BROWN“LIVE” (“L”)
    GREEN AND YELLOW“EARTH” (“E”)
    Disposing of the appliance:
    When disposing of the appliance please remove the plug
    by cutting the mains cable as close as possible to the plug
    body and dispose of it as described above
    GREEN &
    YELLOW
    BROWN
    BLUE13 amp fuse
    CROSS-BAR
    CORD GRIP
     
    						
    							om - 10/2005  - 
     195045696.02
     -   Xerox Business Services - DocuTech
    Viale Aristide Merloni 47 Viale Aristide Merloni 47Viale Aristide Merloni 47 Viale Aristide Merloni 47
    Viale Aristide Merloni 47
    60044 Fabriano (AN) Italy 60044 Fabriano (AN) Italy60044 Fabriano (AN) Italy 60044 Fabriano (AN) Italy
    60044 Fabriano (AN) Italy
    T TT T
    T
    el  +39 0732 6611 el  +39 0732 6611el  +39 0732 6611 el  +39 0732 6611
    el  +39 0732 6611
    www.indesit.com www.indesit.comwww.indesit.com www.indesit.com
    www.indesit.com
     
    						
    All Indesit manuals Comments (0)

    Related Manuals for Indesit Di 450 Installation Manual