Indesit Icd 661 S Manual

							  
   
 9  
  
 
Cutlery Basket 
  
Cutlery should be placed in the cutlery basket with handles at  the bottom. If the rack has side baskets, the spoon should be  
loaded individually into the appropriate slots, especially long  utensils should be placed in the horizontal position at the front of  
the upper basket as shown.  
  For personal safety and a top quality clean, place the silverware in the basket: 
„  They do not nest together.  
„ Place silverware with handles down. 
„ But place knives and other potentially dangerous utensils handles-up.  
 
Plate racks of Basket 
The basket is fitted with plate racks which can be  
stowed horizontal if required.  
 
Cup shelf 
The cup shelf could be stowed standing if 
no cup being placed, which can set more place. 
1  Forks  
2  Soup spoons  
3  Dessert spoons  
4  Teaspoons  
5  Knives  
6  Serving spoons  
7  Gravy ladles  
8  Serving forks 
WARNING! 
■ Do not let any item extend through bottom.  
■  Always load sharp utensils with the sharp point down! 
616
2
1
1
1
2
5
55
1
2
55
1
4
3
3
3
3
4
4
4
7
3
5
4
48
3
2
22 
IN 
						

							 
 
  
 10 
When load bigger Dinner Plates 
 
 
Plate racks of Basket 
When load bigger Dinner plates, please fold the rack 
to left picture showed location. 
The maximum plate can be loaded is 270mm 
(10 inches) diameter.  
						

							  
   
 11 
6. Starting a washing programme 
 
Wash Cycle Table  
 NOTE:  
„  () Means: need to fill rinse into the Rinse-Aid Dispenser. 
„ *En 50242: This program is the test cycle, the rinse-aid dispenser  setting is recommended to Position 6.  
Program Cycle Selection Information Description 
of Cycle DetergentRunning 
time (min) 
Energy 
(Kwh) 
Water 
(l) 
Rinse 
Aid  
For the heaviest soiled loads,  
such as pots, pans, casserole  
dishes and dishes that have  
been sitting with dried food on  
them for a while.  
Pre-wash(50°C)  
Wash (70°C)  
Rinse   
Rinse 
Rinse (70°C)  
Drying  
3/15g  
(or 3 in 1) 145 0.94 11.0 ★  
For normally soiled loads,   
such as pots 、plates、  
glasses and lightly soiled   
pans.   
Pre-wash  
Wash (60°C)  
Rinse  
Rinse (70°C) 
Drying  
3/15g  
(or 3 in 1) 125 0.70 8.4 ★   
Standard daily cycle for  
normally soiled loads,   
such as pots 、plates、  
glasses.   
Pre-wash  
Wash (55°C) 
Rinse 
Rinse (70°C)  
Drying  
3/15g  
(or 3 in 1) 170 0.6 8. ★  
For lightly soiled loads, such as  
glasses, crystal and fine china.  
Wash(45°C)  
Rinse 
Rinse(60°C)   
Drying  
15 g.  75  0.48  6.8 ★   
A shorter wash for lightly soiled  
loads that do not need drying.  
Wash (40°C)  
Rinse  
Rinse  
15 g.  30  0.30  6.0   
To rinse dishes that you plan to  
wash later that day.  Pre-wash   14 0. 01 2.1  
 
Turning On the Appliance 
  
Starting a wash cycle...  
Draw out the basket (see the section entitled Loading the Dishwasher).   
Pour in the detergent (see the section  entitled Salt, Detergent and Rinse Aid).  
Insert the plug into the socket. The power supply is 220-240 VAC 50 Hz, the  
specification of the socket is 10 A 2 50 VAC. Make sure that the water supply  
is turned on to full pressure.  
Rotate the knob, the wash program will be changed as follows direction   
Then press the Start/Pause button, t he dish washer begins to start.  
 NOTE:   
When you press the Start/Pause bu tton to pause during washing, the  
pro gram light will stop blinking a nd the dishwasher will mooing every  
minute unless you press the  Start/Pause button to start.   
55 
						

							 
 
  
 12 
Change the Programme... 
 
Premise: You can modify the washing program, When the dishwasher just runs 
for a short time. Otherwise, the detergent may have already been released, and 
the appliance may have already drained the wash water. If this is the case, the 
detergent dispenser must be refilled (see the section entitled Loading the 
Detergent). 
Press Start/Pause Button more than three seconds the machine will be in stand 
by state, then you can change the program to the desired cycle setting (see the 
section entitled Starting a wash cycle...). 
NOTE:  If you open the door during washing, the machine will pause. When you 
close the door and press the Start/Pause Button, the machine will keep 
on working after 10 seconds. 
The phase lights show the state of the dishwasher: 
a) All phase lights off ----------------------------------- On stand by 
b) One of the phase lights on------------------------- Being paused 
c) One of the phase lights blinking ------------------ Running 
 
 
NOTE: If you open the door when washing, the machine will pause. When you close the door, the 
machine will keep on working after 10 seconds. 
 
Forget to Add a Dish? 
 
A forgotten dish can be added any time before the detergent cup opens. 
  Press the Start/Pause button 
  Open the door a little to stop the washing. 
  After the spray arms stop working, you can open the 
door completely.   Add forgotten dishes.  
  Close the door 
  Press the Start/Pause button, the dishwasher will 
run after 10 seconds. 
 
At the End of the Wash Cycle 
 
When the working cycle has finished, the buzzer of dishwasher will sound 8 seconds, then stop. Turn off the 
appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher. Wait a 
few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still 
hot and more susceptible to breakage. They will also dry better. 
„  Switch Off the Dishwasher 
All the phase lights are off, only in this case the programme has ended.  
1. Switch off the dishwasher by pressing the ON/OFF button.  
2. Turn off the water tap! 
„  Open the door carefully. 
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 
minutes before removing from the appliance. 
Open the dishwashers door, leave it ajar and wait a few minutes before removing the dishes. In this 
way they will be cooler and the drying will be improved. 
„  Unloading the dishwasher 
It is normal that the dishwasher is wet in side. 
 
 WARNING! It is dangerous to open the door when washing, because the hot water may scald you. 
 
6
5
4
3 
2 
1  
						

							 
 
  
 13 
7. Maintenance and Cleaning 
 
Filtering System 
 
The filter prevent larger remnants of food or other objects from getting inside the pump. 
 
Filter assembly 
The filter efficiently removes food particles from the wash water, allowing it to be re-cyclated during the cycle. For best 
performance and results, the filter assembly must be regularly. For this reason, it is a good idea to remove the larger food 
particles trapping in the filter after each wash cycle by rinsing the filter and cup under running water. To remove the filter 
assembly, pull on the cup handle in the upward direction. 
 
    WARNING ! 
„ Never run the dishwasher with out the filters in place. 
„ The dishwasher must never be used without the filters. 
„ Improper replacement of the filter may reduce the performance level of the appliance and damage dishes and utensils. 
 
 
 
 
NOTE: If do it from step1 to step 3, the filter system will be removed; while if do it from Step 3 to Step 1, 
the filter system will be installed. 
 
Main filter   
Food and soil particles trapped by this filter are pulverized by a 
special jet on the spray arm and washed down to drain. 
Fine filter   
This filter holds soil and food residue in the sump area and 
prevents it from being redeposit on the dishes during wash 
cycle  The filter system consists of a coarse filter, a flat (Main filter) 
and a micro filter (fine filter). 
1
2
Coarse filter   
Larger items, such as pieces of bone or glass, that could block 
the drain are trapped in the coarse filter. To remove the items 
caught by the filter, gently squeeze the tap on the top of this 
filter and lift out. 
3
Step 1: contrarotate the Fine filter,  
Step 2: lift it up; 
Step 3: lift the Main filter up 
Open  
						

							 
 
  
 14 
Remarks: 
-  Inspect the filters for blocking every time the dishwasher has been used. 
-  By unscrewing the coarse filter, you can remove the filter system. Remove any food remnants and clean the filters under 
running water. 
 
 
NOTE: The entire filter assembly should be cleaned once a week. 
 
Cleaning The Filter 
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures in the last 
page and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward. 
 
 WARNING! When cleaning the filters, dont knock on them. Otherwise, the filters could be 
contorted and the performance of dishwasher could be debased. 
 
Caring for the Dishwasher 
 
The control panel can be cleaned by using a lightly dampened cloth and dry thoroughly.  
The exterior use a good appliance polish wax. 
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher. 
 
Cleaning The Door 
 
 WARNING! 
„ Never use a spray cleaner to clean the door panel as it may damage the door lock and electrical components. 
„ Abrasive agent or some paper towel should not be used because of the risk of scratching or leaving spots on the stainless steel surface. 
 
Protect Against Freezing 
Please take frost protection measures on dishwasher in winter. Each time after washing cycles,  
please operate as follows: 
1. Cut off electrical power to the dishwasher. 
2. Turn off the water supply and disconnect the water inlet pipe from the water valve.  
3. Drain water from the inlet pipe and water valve. (Use a pan to catch the water)  
4. Reconnect the water inlet pipe to the water valve. 
5. Remove the filter at the bottom of the tub and use a sponge to use up water in sump. 
 
 
NOTE: If your dishwasher can not work because of the ice, please contact professional service persons. 
 
To clean the edge around the door, you should use only a soft warm, damp 
cloth. To avoid penetration of water into the door lock and electrical 
components, do not use a spray cleaner of any kind.  
						

							 
 
  
 15 
Cleaning the Spray Arms 
The spray arms can be easily removed for periodic cleaning of 
the nozzles, to prevent possible clogging. Wash them under 
running water and carefully replace them in their seats, checking 
that their rotary movement is in no way impeded. 
Grasp the middle of the spray arm, pull it up wards to remove it. 
Wash the arms under a jet of running water and return them 
carefully to their seat. After reassembly, check that the spray 
arms turn freely. Otherwise, check that they have been installed 
correctly. 
How to Keep Your Dishwasher in Shape 
„  After Every Wash 
After every wash, turn off the water supply to the 
appliance and leave the door slightly open so that 
moisture and odors are not trapped inside. 
„  Remove the Plug 
Before cleaning or performing maintenance, always 
remove the plug from the socket. 
„  No Solvents or Abrasive Cleaning 
To clean the exterior and rubber parts of the 
dishwasher, do not use solvents or abrasive cleaning 
products. 
Only use a cloth with warm soapy water. 
To remove spots or stains from the surface of the 
interior, use a cloth dampened with water with a little 
vinegar, or a cleaning product made specifically for 
dishwashers. 
„  When it is not in need for a long time 
It is recommend that you run a wash cycle with the 
dishwasher empty and then remove the plug from the 
socket, turn off the water supply and leave the door of 
the appliance slightly open. This will help the door 
seals to last longer and prevent odours from forming 
within the appliance. 
„  Moving the Appliance 
If the appliance must be moved, try to keep it in the 
vertical position. If absolutely necessary, it can be 
positioned on its back. 
„ Seals 
One of the factors that cause odors to form in the 
dishwasher is food that remain strapped in the seals. 
Periodic cleaning with a damp sponge will prevent this 
from occurring. 
 
8. Installation Instruction 
 
 
 
Installation preparation 
 
The installation position of dishwasher should be near the existing inlet and drain hoses and 
power cord. 
One side of the cabinet sink should be chosen to facilitate the connection of drain hoses of the 
dishwasher. 
 
Warning 
Attention 
The installation of the pipes and 
electrical equipments should be done 
by professionals. Electrical Shock Hazard Disconnect 
electrical power before installing 
dishwasher. 
Failure to do so can result in death or 
electrical shock.  
						

							 
 
  
 16 
Positioning the Appliance 
 
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent 
cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to 
facilitate proper installation. 
 
About Power Connection 
 
 WARNING! For personal safety: 
„ DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.  
„ DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING CONNECTION FROM THE POWER CORD. 
Electrical Requirements 
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.  
Use the required fuse 10amp, time delay fuse or circuit breaker recommended and provide separate circuit serving only this 
appliance. 
Electrical Connection 
Ensure the voltage and frequency of the power being corresponds to those on the 
rating plate. Only insert the plug into an electrical socket which is earthed properly. If 
the electrical socket to which the appliance must be connected is not appropriate for 
the plug, replace the socket, rather than using adaptors or the like as they could cause 
over heating and burns. 
 
GROUNDING INSTRUCTIONS 
 „ This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk 
of electric shock by providing a path of least resistance for the electric current. This appliance is equipped 
with a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into 
an appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
 
 WARNING! „ Improper connection of the equipment earthing conductor can result in the risk of an electric shock. 
„ Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly earthed. 
„ Do not modify the plug provided with the appliance. If the plug does not fit properly to the outlet, please have a qualified electrician to install a proper outlet. 
 
Water Connection 
Cold Water Connection 
Connect the cold water supply hose to a threaded 3/4 (inch) connector and make sure that it is 
fastened tightly in place. If the water pipes are new or have not been used for an extended 
period of time, let the water run to make sure that the water is clear and free of impurities. If this 
precaution is not taken, there is a risk that the water inlet can get blocked and damage the 
appliance. 
Hot Water Connection 
The water supply to the appliance can also be connected to the house hot water line 
(centralized system, heating system), as long as it does not exceed a temperature of 60°C. In 
this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency 
slightly reduced. The connection must be made to the hot water line following the same 
procedures as those for the connection to the cold water line. 
 
 WARNING! In order to avoid that there is more water staying in the inlet hose, please close the hydrant after 
using. (Not applicable to appliances without aqua-stop.) 
Insure proper ground 
exists before use  
						

							 
 
  
 17 
Connection of drain hoses 
 
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, 
making sure to avoid bending or crimping it. Use the special plastic support that comes with the 
appliance. The free end of the hose must be at a height lower than75cm and must not be 
immersed in water to avoid the back flow of it. 
 
 
Attention:  
The special plastic hose support must be solidly fastened to the wall to 
prevent the drain hose from moving and allowing water to spill outside 
the drain. 
 
 
max 75 cm  
						

							 
 
  
 18 
 
How to Drain Excess Water From Hoses 
If the sink is 1000 mm higher from the floor, the excess water in hoses cannot be drained directly into the sink. It will be 
necessary to drain excess water from hoses into a bowl or suitable container that is held outside and lower than the sink. 
Water Outlet 
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks. Ensure that the water drain hose is 
not kinked or squashed. 
Extension Hose 
If you need a drain hose extension, observe to use a similar drain hose. 
It must be no longer than 4 meters; otherwise the cleaning effect of the dishwasher could be reduced. 
 
Start of dishwasher 
 
The following things should be checked before starting the dishwasher. 
„  The dishwasher is level and fixed properly  
„  The inlet valve is open 
„  There is a leakage at the connections of the conducts  
„  The wires are tightly connected  
„  The power is switched on  
„  The inlet and drain hoses are knotted 
„  All packing materials and printings should be taken out from the dishwasher 
 
 
Attention: After installation, please make sure to keep this manual.  
The content of this manual is very helpful to the users.