Indesit Ide 1000 Operation Instructions

							User 
Instruction 
Book
for
INDESIT
Dishwasher
Models:
IDE 1000UK
IDE 1005SUK
 
						

							1GB
Safety Is a Good Habit to Get Into
NOTICE
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and proper
installation, use and maintenance of the appliance.
This appliance complies with the following EEC directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
      modifications;
 - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)
and subsequent modifications.
- 97/17/EEC Labelling
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that the appliance
is not damaged. If in doubt, contact a qualified professional.
3.The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet hands or
feet;
- We discourage the use of extension cords and multiple sockets;
- During installation, the power supply cord must not be excessively
or dangerously bent or flattened;
- If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power supply.
Close-up View (control panel)
5.Keep detergents out of the reach of children, who must also be
kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if the area in
which it is installed is covered by a roof; it is also very dangerous to
leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash cycle.
8.Do not lean or sit on the door when it is open, as this could overturn
the dishwasher.
9.If the appliance malfunctions, turn off water supply to the appliance
and disconnect the plug from the wall socket.  Then, consult the
section entitled, Troubleshooting. If you cannot resolve the
problem, contact a service centre.
10.Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing the door
lock.
C
A
D
PF
H
B
R
E
Energico
Quotidiano
Eco
Rapido25 Ammollo
DelicatiSolo x Te
A: ON-OFF button
B: ON-OFF Indicator light
C: Door handle
R: Start/Reset ButtonH: Display
E: Extra drying button
F: Half load button
P: Delayed start select button
IN
S
TL
G H
G: Extra drying indicator light
H: Cycle phase indicator lights
L: Alphanumeric indicator
N: Half load indicator light
S: Low salt indicator light
T: Low rinse aid indicator light
I: Delayed start indicator light
To maintain the EFFICIENCY  and  SAFETY  of this
appliance, we recommend:
lcall only the  Service Centers authorized
by the manufacturer
lalways use original Spare Parts
 
						

							2GB
Close-up View (Interior)
Upper Rack
Top Sprayer Arm
Rack Height Adjustor
Lower Rack
Bottom Sprayer Arm
Salt Container Cap
Washing Filter
Detergent and Rinse Aid Dispenser
M Turbo dry Fan
7H FKQLFDOFKDUDFWH ULVWLFV
Wid th c m.  6 0
Depth cm.  60
Height cm.  85
Capacity 12 standard place settings
Mains water pressure30 KPa÷ 1MPa  (0,3 ÷10 bar)
Power voltage See data plate
Total absorber power See data plate
Fuse See data plate
G
J
I
L
H
F
E
K
M
 
						

							3GB
Salt ......
Salt
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and  minerals
from the water.
Loading the Salt into the Softener
Always use salt intended
for use with dishwashers.
The salt container is
located beneath the
lower rack and should be
filled as follows:
1. Remove the lower rack
and then unscrew and
remove the cap from the
salt container;
2. If you are filling the
container for the first
time, fill it with water;
3. Place the end of the funnel (supplied) into the hole and
introduce about  2 kg of salt. It is normal for a small amount
of water to come out of the salt container.
4. Carefully screw the cap back on.
The salt container should be filled up when the low
salt indicator light S flashes.
Once you have loaded the salt for the first time, it is normal
that the low salt indicator light stays on or flashes for about
5 consecutive cycles.
Warning: To prevent rust from forming, we advise you to
load the salt before starting a wash cycle.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the
amount of salt consumed based
on the harness of the water
used. This is intended to
optimize and customize the
level of salt consumption so that
it remains at a minimum.
Your Local Water Board can
supply the degree of hardness
of the water
in your area.
To adjust salt consumption, pro-
ceed as follows:
1) Unscrew the cap from the salt container.
2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti-
clockwise direction from the _ setting towards the +
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord-
ance with the following schema:
Water Hardness
Clarke
degrees°fH mmol/lSelector
positionSalt
consu-
mption
(grams/-
cycle)Autono-
my
(cycles\2-
kg)
0 - 14 0 - 17 0 -1,7 / 0 /
14 - 36 18 - 44 1,8 - 4,4 - 20 60
36 - 71 45 -  89 4,5 -  8,9 MED 40 40
>71 >89 > 8,9 + 60 25
 
						

							4GB
Detergent and Rinse Aid ....
Detergent
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the
start of each wash cycle following the instructions provided
in the Wash Cycle Table. The detergent dispenser is
located on the inside panel of the door.
Loading the detergent
To open lid A, press button B. The cleaning detergent
should be introduced  into the two containers Cand
D up to the rim.
After pouring in the detergent, replace the lid, pressing
down until it clicks.
Dishwasher detergent in tablets is now available on the
market, in which case you should place one tablet into
container D and replace the lid.
Notice: To facilitate closing the cover, remove any
excess detergent on the edges of the dispenser.Rinse Aid
This product makes dishes sparkle more as it improves their
drying. The rinse aid container is situated on the inside of
the appliance door; you should refill it when the low rinse
aid indicator light T flashes.
Loading the Rinse Aid
To open the dispenser, turn the C cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to
overfill. The amount of rinse aid used for each cycle can be
regulated by turning the F dose adjustor, located beneath
the C cap, with a screwdriver.  There are 6 different
settings; the normal dosage setting is  4.
Important:
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting.  If
the dishes have white streaks, turn the dosage adjustor to
a lower setting.
Warning
Three-in-one dishwasher tablets are now available on the market, and combine the detergent, salt and rinse aid all in one.
If the water in your area is hard or very hard, we still recommend you pour extra salt into the relevant dispenser to prevent
the formation of white streaks on your dishes or on the appliance interior.
Add rinse aid to the corresponding container only if you are dissatisfied with the results on your dishes.
In any case, please read the manufacturers instructions provided on the packet.
If you use only these products, it is normal for the salt and rinse aid indicator lights to flash permanently after a certain
number of cycles.
25 gr.5 gr.
CD
B
A
F
D
C
 
						

							5GB
Loading the Dishwasher
Before placing the dishes in the racks, remove the largest
scraps of food left over on your plates, you will thus avoid
blocking the filter, which would reduce the efficacy of the
wash.
If the saucepans and frying pans are very dirty, allow them to
soak before being washed.
You will thus avoid having to wash them again.
To make it easier to load your dishes, pull the racks out fully.
How to use the lower rack
We recommend you place the most difficult dishes to wash
into the lower rack: saucepans, lids, soup dishes and plates
(load examples are shown in the photo).
• Serving dishes and large lids: place them on the sides
of the rack.
• Saucepans, salad bowls: must always be placed upside
down.
• Very deep dishes: place them obliquely, thus allowing
water to run down them and cleaning them better.
The cutlery basket (Figures A,B)
The cutlery basket can be split up by pulling out the handle
and removing the clip that
keeps the two parts joined
together (see figures A and B).
When you only have little
cutlery to wash, you can use
just half the basket.
This basket is equipped with
two removable grids: insert
the cutlery one by one into the
slots, with the handles at the
bottom. Position them so that
they dont touch.
How to use the upper rack
Place delicate and lightweight dishes in the upper rack:
glasses, tea cups and coffee cups, saucers - but plates too
- shallow salad bowls, slightly dirty frying pans and shallow
pans (the photo illustrates a few examples).
Position lightweight dishes in such as way as to avoid their
being moved by the spray of water.
The upper rack can be equipped with one or two special
tip-up compartments for mugs and cups, as well as spoons,
knives and forks, which should be fitted in the slots
provided. Stemmed glasses can be hooked onto these
compartments by threading the stems into the slots
provided (see fig. D).
After loading the dishes, remember to check that the blades
on the sprayer arms can turn freely without knocking
against any dishes.
How to adjust the upper rack ….
The upper rack can be set in a high or low position. There
are two handles on the sides of the upper rack: use these
to adjust its height (see figure C).lower rack upper rackLoad examples
fig. C
fig. A
fig. B
fig. D
fig. A
 
						

							6GB
Turning on the Appliance
First of all
Insert the plug into the electricity socket to power the
dishwasher. Turn on the water tap completely and press ON-
OFF button A; the display lights up and the wash cycle
time selected on the knob will flash.
Selecting and starting a wash cycle.
• Select the desired wash cycle by turning knob D
clockwise from wash cycle 1 to 7 and anticlockwise from 7
to 1; the display indicates the average duration of the wash
cycle and the cycle phases it consists of (consult the wash
cycle table contained on page 7, especially when first using
the appliance).
• Press the Start button R and the wash cycle starts up,
emitting a double beep; the approximate amount of time
left until the end of the wash cycle is displayed.
• If the time indicated at the start of the wash cycle does
not correspond to the actual duration of the cycle itself, this
could be for a number of reasons: the temperature of the
inlet water, the degree of soil, prolonged attempts by the
appliance to clean the wash filter from food residue clogging
it, etc.
Cycle phase under way indicator
While the wash cycle is under way, the symbols corresponding
to the cycle phases light up in sequence.
Here are the symbols corresponding to each cycle phase:
       Pre-wash      Wash        Rinses      Drying
Cancelling and modifying a wash cycle in progress
Premise: a wash cycle in progress can only be modified if it
hasnt been running for long.
Keep the Reset button R pressed for about 3 seconds:
a prolonged beep will sound, followed by three short beeps.
The cancelled cycle time will flash on the display. Turn the
knob to select a new wash cycle.Youve left out a dish?
You can interrupt a wash cycle by pressing the ON-OFF
button, then place the forgotten dishes into the appliance,
which will start up, after approximately 10 seconds, from
where it was interrupted when you turn it back on.
Theres been a power failure? Has the dishwasher door
been opened?
The wash cycle stops and 3 dashes appear on the display;
the cycle restarts as soon as the electricity comes back on or
when the door is shut.
At the end of the wash cycle
The end of the wash cycle is indicated by two short beeps
and the word END flashes on the display.
• Turn the appliance off at the ON-OFF button
• Turn off the water tap.
• Empty the lower rack first.
Make sure the wash cycle has ended before removing the
dishes!
Warning: when you open the dishwasher door after the wash
cycle has just ended or is under way, take care not to scald
yourself with the hot steam.
How to set the extra drying     
Press button E. After a prolonged beep, indicator light
G lights up and the time corresponding to the wash cycle
selected on the knob will flash on the display.
Note: The time indicated on the display is extended due to
the extra drying time.
To disable the extra drying option, press the same button
and indicator light G will be turned off after a  beep is
sounded.
This option is incompatible with the soak cycle.
 
						

							7GB
Setting a half load and a delayed start
How to set a delayed start    
When you have loaded the dishes, you can choose when to
start your dishwasher before setting the wash cycle desired.
• Press button P repeatedly to postpone the start of the
wash cycle from 1 hour to 24h.
• If you press the button again, the word OFF is displayed
(no selection made).
Once you have made your selection, make sure the appliance
door is shut and start the wash cycle by pressing the START
button.
Symbol I lights up on the display and the countdown
begins.
• Once the countdown is up, the wash cycle begins and the
approximate amount of time left until the end of the wash
cycle is displayed.
Have you changed your mind?
• If you change your mind, you can set a shorter time delay:
press button D to select it. You need not reset the wash
cycle.
• If you have changed your mind and wish to start the wash
cycle immediately, press button P until the countdown is
fully reset. Indicator light I will turn off and the cycle will
start at the sound of a beep.
The indicator light corresponding to the cycle phase under
way will come up on the display and the countdown to the
estimated cycle end begins.You want to wash on one rack only?   Remember to use half the amount of detergent.
When you only have little cutlery to wash, you can run just
half a load on the upper rack, saving on both water and
electricity.
• Press button F; you will hear a beep and the symbol
corresponding to the half load will light up.
Once you have made your setting, start the wash cycle by
pressing the START button.
-  This option is available with all wash cycles.
-  The Just You wash cycle is programmed to wash on the
upper rack only.
Warning: if the display indicates the word dON when you turn
your dishwasher on, this means the demo mode is in operation. This
mode is useful for exhibitors in that it simulates the wash cycles
without actually carrying them out.
To quit this mode, keep the START/RESET button R pressed for
approximately 4 seconds. The word dOF will be displayed once
you have quit the demo mode successfully.
 
						

							8GB
Wash Cycle Table
Dishwasher washing guarantees your dishes will be cleaned in a hygienic setting for
safer, cleaner results.
&\FOH&\FOH  VH OH FWLRQ
LQV WUXFWLRQV&\FOHGHVFULSWLRQ
HWHUJHQW
IRU SUH ZDV K
ZDVK5LQVH$LG:D V K  F \ F O H
GXUDWLRQ
“
PD UJ LQ
ZL W KR XW
H[WUD
GU\ LQJ 
,QWH QV LYH
Ve r y  d i r t y  d i s h e s  a n d
pans (not to be used
fo r  d e lic a te  ite ms )Pre- wash with hot water at 40°C
Extended wash at 65°C
2 cold rinses
Hot rinse at 65°C
Drying.  
.
J


7LPH   
						

							9GB
Energy Saving Tips
- It is important to try and run the dishwasher when it is
fully loaded in order to save on energy. In order to prevent
odors from forming and food from caking onto the dishes,
you can run the hold cycle.
- Choose the right wash cycle: the choice of cycle depends
on the type of dishware, cookware and utensils being
washed and how dirty they are.- Use the right amount of detergent: if you use too much
detergent, the result will not be cleaner dishes, but, rather,
a greater negative impact on the environment.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
How to Keep Your Dishwasher in Shape
After Every Wash
After every wash, turn off the water supply to the appliance
and leave the door slightly ajar so that moisture and odors
are not trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove
the plug from the socket. Do not run risks.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products. Rather,
use only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior,
use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.When You Go on Holiday
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming within
the appliance.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its
back.
Seals
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals. Periodic
cleaning with a damp sponge will prevent this from occuring.