InFocus LP 260 Projector User Manual

13
Using the Remote Control
To control the computer ’s mouse from the projector ’s remote or 
keypad, you must connect one of the Control cables to the com-
puter. See page 7 for details. 
Turn the remote on using the 
on/off button on the side of the 
remote. Point the remote control at the projection screen or at the 
front of the projector (not at the computer). The range for opti-
mum operation is about 16 feet and 60 degrees from the front of 
the projector (see Figure 10). If you point the remote...

14
Using the Projector
F
IGURE 11
Remote control
Press anywhere on the edge of the point button to move the cur-
sor on the screen. You can move the cursor at any angle by press-
ing the corresponding edge of the button. See “Using the Keypad 
and Remote Buttons” starting on page 15 for a description of the 
function buttons.
If you are creating presentations in Microsoft
® PowerPoint®, you 
can use the remote’s 
right click, select, and point buttons to navi-
gate through your presentation while in...

15
Using the Keypad and Remote Buttons
FIGURE 12
Keypad buttons
Point button (1 button on remote, 4 buttons on keypad)
Press this button to navigate in the menus, make adjustments to 
menu items, or pan the image in Digital Zoom mode. When you 
press the center of this button on the remote, it works like the 
select button.
Select button
Use the select button to confirm a selection in the menus. See 
“Using the On-Screen Menus” on page 17.
Po w e r
Press this to turn the projector on and off. See page 9...

16
Using the Projector
Source (keypad only) or Computer and Video (remote only)
When you have more than one source (computer and video) con-
nected to the projector, select between them by pressing the 
source button on the keypad or the computer or video button on 
the remote. 
Ke y s t o n e
Use this button to adjust the keystone distortion. See page 12 for 
details.
d. zoom (digital zoom)
This allows you to zoom a computer image. See page 25 for 
details.
Vo l u m e  
To increase the volume, press...

17
Using the On-Screen Menus
The projector
 has menus that allow you to make image adjust-
ments and change a variety of settings. Most of these adjustments 
aren’t available directly from the keypad. 
NOTE: Some menu items may be 
grayed out (dimmed) at certain 
times. This indicates the item is 
not applicable to your setup or the 
item is not enabled until another 
selection is made.
To open the on-screen menus, press the menu button on the 
remote or keypad. A red frame appears around the selected...

18
Using the Projector
Computer Adjustments
Select Computer mode by pressing the 
source button on the key-
pad, pressing the 
computer button on the remote, or clicking the 
Computer icon in the menu. When you select Computer, the cur-
rent mode display appears, showing details of the connected 
computer.
System Menu
The projector automatically adjusts to most incoming computer 
signals and projects the image without any user interaction. If a 
problem is encountered, the message “Go to PC adj.” may...

19
2Press the point down button, move the arrow to the system you 
want to select, then press the 
select button. 
These systems are set up using the PC Adjustment menu.
PC Adjustment
NOTE: This feature is not avail-
able when RGB, HDTV1035i, or 
HDTV1080i is selected in the Sys-
tem menu.
The projector automatically adjusts to most incoming computer 
signals and projects the image without any user interaction. 
However, some computers employ unique signal formats that the 
projector cannot handle...

20
Using the Projector
3Move to the parameter you want to change using the point up/
down
 buttons, and adjust each setting using the point right/left 
buttons.
4Navigate to “Save” and press the 
select button.
The parameter is memorized in the selected mode.
5To activate the mode, select it in the System Select menu (see 
“System Menu” on page 18.)
To t a l  L i n e s
The number of vertical lines. 
Horiz. Size
The number of dots in one horizontal period.
H Position/V Position
The left/right and up/down...

21
Display area
The area displayed by the projector. Point the arrow at the Dis-
play area option and press the 
select button to open a dialog box 
where you can select the resolution from a list, or adjust the value 
with the left and right 
point buttons.
Full Screen
Select On to resize the image with a 4x3 aspect ratio.
After adjusting the settings, press Save to save the settings, press 
Reset to recall the saved settings, press Mode Free to clear the 
previously saved settings, and press Quit to...

22
Using the Projector
Image Menu
The Image menu allows you to manually adjust the image.
1Select the Image menu.
The “Image Adjustments” menu appears.
Fine sync
Adjust the sync as necessary from 0 to 255 to eliminate flicker in 
the image.
Horiz. Size
Press the point buttons to adjust the number of dots in one hori-
zontal period.
Color Balance (Red, Green, Blue)
Press the point left button to lighten the color and the point right 
button to deepen the color from 0 to 63.
Contrast
Press the point left...