InFocus LP130 Projector User Manual

							15
Reset (keypad only)
Resets the options in the menus (except Language, Video Stan-
dard, and Rear Projection) to their original settings.
Keystone + - (remote only) 
Use this feature to adjust the image vertically and make a squarer 
image.
1Press the 
keystone + button to reduce the upper part of the 
image, and press the 
key sto ne  - button to reduce the lower 
part. You can also adjust keystone from the Display menu (see 
page 17 for details on the menu).
FIGURE 12
Adjusting the keystone
Forward/back buttons (remote only) 
These buttons act like the page up and page down buttons on 
your computer ’s keyboard. You can use them to advance through 
a slide show in PowerPoint™ presentations. To use this feature, 
you must connect the USB mouse connector on the computer 
cable to your computer. See page 7 for details.
Up/down arrow buttons
Use these buttons to navigate through and make adjustments to 
the on-screen menus. See “Using the On-Screen Menus” on 
page 16 for details.
increasing keystonedecreasing keystone 
						

							16
Using the Projector
Using the On-Screen Menus
The projector
 has menus that allow you to make image adjust-
ments and change a variety of settings. These adjustments aren’t 
available directly from the keypad. 
NOTE: Some menu items may be
grayed out (dimmed) at certain
times. This indicates the item is
not applicable to your setup or the
item is not enabled until another
selection is made.
To open the on-screen menus, press the menu/select button on the 
keypad or remote. (The menus automatically close after 30 
seconds if no buttons are pressed.) This displays the Main menu 
and changes the source and reset buttons on the keypad to menu 
navigation buttons. Press the 
 button to move the cursor 
down and press the   button to move the cursor up. The 
selected menu is highlighted. 
FIGURE 13
Main menu
To change a menu setting, use the up and down arrow buttons to 
move the cursor up and down to the item you want to change 
(the selected item is highlighted), then press 
menu/select. When 
an item is selected, its button appears depressed to provide a 
visual indication of selection. Use the up and down arrows to 
adjust the setting or turn it on and off. Press 
menu/select when 
you are done. Press the up and down arrows to move to another 
setting. When you have completed your adjustments, navigate to 
Exit, then press 
menu/select. You are returned to the top of the 
Main menu. Press 
menu/select again to exit the Main menu, or 
navigate to another submenu. 
						

							17
Display Menu
To access the Display menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight Dis-
play, then press 
menu/select again to access the Display menu.
 
FIGURE 14
Display menu
Ke y s t o n e
This option helps to keep the image square as the angle of projec-
tion is changed. Use this feature to adjust the image vertically 
and make a squarer image. See page 15 for details on keystone 
adjustments.
1Press the down button to highlight Keystone, then press 
menu/select. Use the up and down arrows to adjust the key-
stone setting. Press 
menu/select to accept your changes.
Brightness
Adjusting the brightness changes the intensity of the image.
1Use the up and down arrows to highlight Brightness, press 
menu/select, use the arrows to adjust the brightness, then 
press 
menu/select to accept your changes. 
						

							18
Using the Projector
Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. Adjusting the contrast changes 
the amount of black and white in the image.
1Use the up and down arrows to highlight Contrast, press 
menu/select, use the arrows to adjust the contrast, then press 
menu/select to accept your changes.
Tint
NOTE: The color setting applies
to video sources only. The tint
setting applies to NTSC video
sources only.
The tint adjusts the red-green color balance in the projected 
image. 
1Use the up and down arrows to highlight Tint, press 
menu/select, use the arrows to adjust the tint, then press 
menu/select to accept your changes.
Color
The color setting adjusts a video image from black and white to 
fully saturated color.
1Use the up and down arrows to highlight Color, press 
menu/select, use the arrows to adjust the color, then press 
menu/select to accept your changes.
Blank screen
Blank Screen determines what color is displayed when there is no 
active source and when the projector is in standby.
1Use the up and down arrows to highlight Blank screen, press 
menu/select, use the arrows to cycle through the options blue, 
black, and white, then press 
menu/select to accept your selec-
tion. 
						

							19
Image Menu for Computer Sources
To access the Image menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight 
Image, then press 
menu/select again to access the Image menu.
FIGURE 15
Image menu for computer sources
Resize
Resize 
allows you to select from among four different re-sizing 
options. The default is 
Standard, which resizes the image from its 
original version to fit a standard 4x3 aspect ratio screen. 
Wide-
screen Letterbox
 preserves the 16x9 aspect ratio of the original 
theater version, but the image is placed in a 4x3 space, so black 
bars appear at the top and bottom of the image. 
Enhanced Wide-
screen
 also preserves the aspect ratio of the original theater ver-
sion and is designed to be used with content that is Enhanced for 
Widescreen TVs. This option yields more detail than Widescreen 
Letterbox. 
Native reduces the Standard size to match the height of 
Enhanced Widescreen. 
Highlight 
Resize, press menu/select, use the up or down arrow 
buttons to cycle through the options, then press 
menu/select to 
select.
Auto Image
The projector automatically adjusts tracking, signal synchroniza-
tion and vertical and horizontal position for most computers. If 
you want to adjust these features manually, you must turn off 
Auto image first. 
Highlight 
Auto image, press menu/select, then press the up or 
down arrow buttons to turn this feature off and on. 
						

							20
Using the Projector
Manual Sync 
The projector adjusts signal synchronization automatically for 
most computers. But if the projected computer image looks fuzzy 
or streaked, try turning 
Auto image off then back on again. If the 
image still looks bad, try adjusting the signal synchronization 
manually:
1Tu r n  A u t o  I m a g e  o f f .
2Highlight Manual sync, press 
menu/select, use the arrow but-
tons to adjust Manual sync until the image is sharp and free of 
streaks, then press 
menu/select.
Manual Tracking 
The projector adjusts tracking automatically to match the video 
signal from your computer. However, if the display shows evenly 
spaced, fuzzy, vertical lines or if the projected image is too wide 
or too narrow for the screen, try turning 
Auto Image off then back 
on again. If the image is still bad, try adjusting the tracking man-
ually:
NOTE: The Manual Sync,
Manual Tracking, Horizontal
Position and Ve r t i c a l  P o s i t i o n
options are available only for
analog computer sources. The
projector sets these options
automatically for digital computer
and video sources, with no manual
override.
1Tu r n  A u t o  i m a g e  o f f .
2Highlight Manual tracking, press 
menu/select, use the arrow 
buttons to adjust Manual tracking until the fuzzy vertical bars 
are gone, then press 
menu/select.
Horizontal Position 
Follow these steps to manually adjust the horizontal position:
1Tu r n  A u t o  i m a g e  o f f .
2Highlight Horizontal position, press 
menu/select, use the 
arrow buttons to adjust the Horizontal position, then press 
menu/select.
Positioning adjustments are saved when you turn off the projec-
tor.
Ve r t i c a l  Po s i t i o n  
Follow these steps to manually adjust the vertical position.
1Tu r n  A u t o  i m a g e  o f f .
2Highlight Vertical position, press 
menu/select, use the arrow 
buttons to adjust the Vertical position, then press 
menu/select.
Positioning adjustments are saved when you turn off the projec-
tor. 
						

							21
Image Menu for Video Sources
FIGURE 16
Image menu for video sources
Resize
Resize 
allows you to select from among four different re-sizing 
options. The default is 
Standard, which resizes the image from its 
original version to fit a standard 4x3 aspect ratio screen. 
Wide-
screen Letterbox
 preserves the 16x9 aspect ratio of the original 
theater version, but the image is placed in a 4x3 space, so black 
bars appear at the top and bottom of the image. 
Enhanced Wide-
screen
 also preserves the aspect ratio of the original theater ver-
sion and is designed to be used with content that is Enhanced for 
Widescreen TVs. This option yields more detail than Widescreen 
Letterbox. 
Native reduces the Standard size to match the height of 
Enhanced Widescreen.
Highlight 
Resize, press menu/select, use the up or down arrows to 
cycle through the options, then press 
menu/select.
Video Standard (video sources only)
When Video is set to Auto, the projector attempts to pick the 
video standard (NTSC, NTSC 4.43, PAL, or SECAM) automati-
cally based on the input signal it receives. (The video standard 
options may vary depending on your region of the world.) If the 
projector is unable to detect the correct standard, the colors might 
not look right or the image might appear “torn.” If this happens, 
manually select a video standard.
Highlight 
Video standard, press menu/select, use the up or down 
arrows to cycle through the options, then press 
menu/select to 
select. 
						

							22
Using the Projector
Control Menu
To access the Control menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight 
Control, then press 
menu/select again to access the Control menu.
FIGURE 17
Control menu
Auto Source 
When this feature is On, the projector automatically finds the 
active source, checking the default source first. When this feature 
is Off, the projector defaults to the source selected in Default 
Source. To display another source, you must manually select one 
by pressing the 
source button on the keypad or the data or video 
button on the remote. 
Highlight 
Auto source, press menu/select, then press the up or 
down arrow buttons to turn this feature off and on.
Default Source
This determines which source the projector checks first for active 
video during power-up. Select among Data-Analog, Data-Digital, 
composite video, and S-Video.
Highlight 
Default source, press menu/select, use the up or down 
arrows to cycle through the options, then press 
menu/select to 
select. 
						

							23
Advanced Menu
To access the Advanced menu settings, press the 
menu/select but-
ton to display the Main menu, press the down arrow to highlight 
Advanced, then press 
menu/select again to access the Advanced 
menu.
FIGURE 18
Advanced menu
Rear Projection
When you turn Rear Projection on, the projector reverses the 
image so you can project from behind a translucent screen. 
Highlight 
Rear Projection, press menu/select, then press the up or 
down arrow buttons to turn this feature off and on.
Reset
Highlight Reset then press menu/select to reset the options in the 
menus (except Language, Video Standard, and Rear Projection) to 
their original settings.  
						

							24
Using the Projector
Language Menu
FIGURE 19
Language menu
You can display the on-screen menus in English, French, German, 
Spanish, Chinese or Japanese. 
1Press the 
menu/select button to display the Main menu, press 
the arrow buttons to highlight Language, then press 
menu/select again to access the Language menu.
2Press the arrow buttons to highlight the desired language, 
then press 
menu/select. Press menu/select to exit this menu and 
return to the Main menu.