InFocus Projector In102 User Manual

Operation 41
FUNCTIONDESCRIPTION
Presentation 
TimerReminds the presenter to finish the presentation within a 
certain time frame. See Setting the presentation timer on 
page 33 for details.
LanguageSets the language for the On-Screen Display (OSD) menus. 
See Using the menus on page 21 for details.
Projector 
PositionThe projector can be installed on a ceiling or behind a screen. 
See Choosing a location on page 9 for details.
Auto Power 
OffAllows the projector to turn off automatically if no input...

Operation 42
FUNCTIONDESCRIPTION
Quick 
Cooling
Selecting On enables the function and the projector cooling 
time will be shortened to a few seconds.
If you attempt to restart the projector right after the quick 
cooling process, it may not be turned on successfully and will 
rerun its cooling fans.
High Altitude 
ModeA mode for operation in high altitude areas. See Operating in a 
high altitude environment on page 35 for details.
Audio 
SettingsMute
Volume
See Adjusting the sound on page 35 for...

Operation 43
FUNCTIONDESCRIPTION
VGA Out
Selecting On enables the function. The projector can output a 
VGA signal when it is in standby mode and the D-SUB IN and 
D-SUB OUT sockets are correctly connected to devices. See 
Connecting a monitor on page 15 for how to make the 
connection.
Enabling this function slightly increases the standby power 
consumption.
Lamp 
Settings
Lamp mode
See Setting Lamp mode as Economic on page 45 for details.
Reset lamp timer
See Resetting the lamp timer on page 49 for...

Maintenance 44
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular 
basis is to keep the lens clean.
Never remove any parts of the projector except the lamp. If your projector needs 
service, contact InFocus Corporation (www.infocus.com/support) or your dealer for 
assistance.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. 
 Use a canister of compressed air to remove dust.
 If there is dirt or smears,...

Maintenance 45
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is 
automatically calculated by the built-in timer. The timer displays lamp hours used in 
Normal mode, plus equivalent Economic mode hours. Equivalent Economic 
mode hours are calculated as follows:
1 lamp hour (in Normal mode) = 1.33 lamp hours (in Economic mode)
See Setting Lamp mode as Economic below for more information on Economic mode.
To obtain the lamp hour...

Maintenance 46
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time 
to replace the lamp, please install a new lamp or consult your dealer. An old lamp 
may cause a malfunction in the projector and in some instances the lamp may 
explode.
CAUTION
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator 
still lights...

Maintenance 47
Replacing the lamp
WARNING
Hg - Lamp contains mercury. Manage in accordance with local 
disposal laws. See www.lamprecycle.org
• To reduce the risk of electrical shock, always turn the projector off and disconnect the 
power cord before changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution 
when removing lamp glass...

Maintenance 485. Pull out the lamp connector from a 
slot in the lamp compartment. 
Disconnect it from the projector as 
illustrated.
6. Lift the handle so that it stands up. 
Use the handle to slowly pull the 
lamp out of the projector.
CAUTION
• Pulling it too quickly may cause the lamp 
to break and scatter broken glass in the 
projector.
• Do not place the lamp in locations where 
water might splash on it, children can 
reach it, or near flammable materials.
• Do not insert your hands into the...

Maintenance 49 13. Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-
Screen Display (OSD) menu. Go to the 
SYSTEM SETUP: Advanced > Lamp 
Settings menu. Press MODE/ENTER. 
The Lamp Settings page displays. 
Press  to highlight Reset lamp timer 
and press MODE/ENTER. A warning message displays asking if you want to 
reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp 
time will be reset to...

Maintenance 50
Indicators
LightStatus & Description
PowerTe m pLamp
Power events
Orange Orange OrangeThe projector has just been connected to a power 
outlet.
Orange Off OffStand-by mode
Green
FlashingOff OffPowering up
Green Off OffNormal operation
Orange
FlashingOff Off
1. The projector needs 90 seconds to cool down as it 
was abnormally shut down without the normal 
cooling down process. Or
2. The projector needs to cool for 90 seconds after 
the power is turned off.
Orange
FlashingOff OffThe...