InFocus Projector IN1118 User Manual

							30
6Navigate to the item you wish to copy and press Select. A green checkmark 
appears next to the selected item.
7Navigate to the Local or USB directory tab.
8Navigate to the location you wish to paste the item into and press Select.
9Navigate to Paste and press Select.  
						

							31
Maintenance
Cleaning the lens
1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
•Projector must be off and the lens must be at room temperature.
•Avoid using an excessive amount of cleaner, and don’t apply the cleaner 
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals 
might scratch the lens.
2Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
•Turn the projector off and unplug power cord before cleaning any part of 
the projector.
•Do not touch or block the projector lens with any objects as this can 
damage the projector lens. Scratches, gouges and other lens damage are not 
covered by the product warranty.
•Do not open any cover on the projector, except the lamp cover.
•Do not attempt to service this product yourself as opening and removing 
covers may expose you to dangerous voltage and other hazards. Refer all 
servicing to qualified service personnel.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the 
information that came with the lock for instructions on how to use it.
Security Lock 
						

							32
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the 
lamp has been in use.
• NOTE: Be sure to use the InFocus lamp module designed for this projector. 
You can order new lamps from www.infocus.com (in select areas), your 
retailer or your dealer. Only genuine InFocus lamps are tested for use in this 
projector. Use of non InFocus lamps may cause electrical shock and fire, and 
may void the projector warranty.  InFocus is not liable for the performance, 
safety or certification of any other lamps.
WARNINGS:
• The projector uses a high-pressure mercury glass lamp.  The lamp may fail 
prematurely, or it may rupture with a popping sound if jolted, scratched, or 
handled while hot.  The risk of lamp failure or rupture also increases as the 
lamp age increases; please replace the lamp when you see the “Replace Lamp” 
message.
• To avoid burns, allow the projector to cool for at least 60 minutes before you 
replace the lamp.
• Do not touch or block the projector lens with any objects as this can damage 
the projector lens. Scratches, gouges and other lens damage are not covered 
by the product warranty. 
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass surface of the lamp module. Fingerprints can obscure 
projection sharpness and may cause the glass to shatter.
• Be extremely careful when removing the lamp housing. In the unlikely event 
that the lamp ruptures, small glass fragments may be generated. The lamp 
module is designed to contain most of these fragments, but use caution when 
removing it. 
• Before replacing a ruptured lamp, clean the lamp compartment and dispose of 
cleaning materials. Wash hands after lamp replacement. 
• When replacing the lamp while the projector is ceiling-mounted, wear 
protective eyewear to prevent eye injury.
Hg – Lamp contains mercury. Manage in accordance with local disposal 
laws. See www.lamprecycle.org. 
						

							33
1Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly. 
3Remove the lamp door, press down on the button in the center of the lamp 
door and remove the end cover. 
4Remove the screw holding the lamp door, slide the door to the right and lift 
the door off the projector.
5Loosen the captive screws that attach the lamp housing to the projector.  
NOTE: If the projector is installed on a ceiling mount, be careful not to drop 
the lamp module once the captive screws are loosened.
6Carefully lift the lamp straight up, off of the alignment pins; being careful not to 
pinch the lamp connector. Dispose of the lamp in an environmentally proper 
manner.
7Install the new lamp module, aligning the pins properly. Be careful not to pinch 
the lamp connector.
8Tighten the screws. (NOTE: If the pins have not been aligned properly, the 
screws will not tighten securely.)
9Replace the lamp door by (a) putting the lamp door down and (b) sliding it to 
the left.
10Replace the lamp door screw and tighten securely.
11Replace the end cover.
12Plug in the power cord and press the Power button to turn the projector back 
on.
13To reset the lamp hour timer, navigate to the Advanced Menu > Status/Service 
menu and select Reset Lamp Hours....
turn off and unplug 
projectorwait 60 minutes
loosen screws 
						

							34 Numerics
3D Sync Invert 25
A
AC Power On 27
Aspect Ratio 24
Audio In 7
Auto Image 24
Auto Off Time 27
Auto Source 27
AV  M u t e  2 6
B
Blank Key 26
Blank Screen 26
Brightness 24
C
Cable box 10
Ceiling Mount 24, 26
Closed Captions 26
Color Space 25
Computer In7, 26
Connecting
Video device 10
Contacting InFocus 18
Contrast 24
Customer service contact information 18
D
Digital Zoom 26
E
Eco Blanking 27
F
Factory Reset 27
Focus 9Freeze Screen 26
G
Gamma 25
H
HDMI 26
HDTV 24
High Altitude Setting 27
Horizontal Position 25
Horz Shift 26
I
Instant Power On 27
Internal Speaker 26
K
Ke y p a d  2 6
Ke y p a d  b u t t o n s  2 1
Ke y s t o n e  2 4
L
LightCast Reader 10, 28
M
Magnify Level 26
Menu Transparency 26
Menu usage 23
Mute 26
O
Overscan 25, 26
P
Phase 25
PIN Protect 26
Power connector 7
Power cord 7
Power Saving Mode 27
Prevent PC Screen Saver 25
Programmed Dimming 26 
						

							35 Projector
Connecting video devices 10
Key p a d  b u t t o n s  2 1
Menus 23
Positioning 6
Setting up 6
Troubleshooting problems 11
Projector Info 26, 27
R
Rear Project 26
Red/Green/Blue Gain 25
Red/Green/Blue Offset 25
Remote control 19
Resetting the projector 27
S
Screen Aspect 10
Search Screen 27
Service 27
Sharpness 24
Show Messages 26
Source 26
Source Info 26, 27
Sync Threshold 25
T
Tint 25
Tracking 25
Troubleshooting 11
TV tuner 10
U
USB 5
V
Ve r t  S h i f t  2 6
Ve r t i c a l  P o s i t i o n  2 5Vo l u m e  2 4
Vo l u m e  b u t t o n  2 0
W
Wa rr a n t y  1 8
Z
Zoom 9