InFocus Projector IN2124a User Manual

30
Timer
Auto Off Time: automatically turns the projector off after no signals are detected for 
a preset number of minutes. If an active signal is received before the projector powers 
down, the image will be displayed.
High Altitude Setting
High Altitude: We recommend you turn on the High Altitude Mode when your envi-
ronment is between 5000 (1500m) and 10,000 (3000m) above sea level.
Network
Wired LAN
DHCP: Abbreviation for Dynamic Host Configuration Protocol. This 
protocol automatically assigns IP...

31
Controlling the projector through a LAN 
environment
The projector supports Crestron® software. With correct settings for the 
Network menu, you can manage the projector from a computer using a web 
browser when
 the computer and the projector are properly connected to the 
same local area network.
Wired connection
1Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the 
projector and the other end to the RJ45 port .
2Press Menu on the keypad or remote and then go to Advanced Menu >...

32
Wireless connection
To connect to the projector wirelessly, you need to plug an optional InFocus 
wireless dongle (p/n SP-WIFIUSB-2) to the USB Type A connector on the 
projector.
How to setup AP mode:
1Make sure the projector is turned on.
2Select Type-A from source list.
3Go to Settings > WiFi, select AP Mode and set it to ON. See page 47. AP 
mode is set to ON by default. 
4Press Menu on the keypad or remote and then go to Advanced Menu > Setup 
> Network menu.
5Make sure SSID and IP Address...

33
Web controlling the projector
Once you have the correct IP address for the projector and the projector is on or 
in
 standby mode, you can use any computer that is on the same local area network 
to
 control the projector.
•If you are using Microsoft Internet Explorer, make sure it is version 7.0 or 
higher.
•The screenshots in this manual are for reference only, and may differ 
depending on your browser.
1Enter the address of the projector in the address bar of your browser and 
press Enter. 
2The...

34
About Crestron e-Control®
1The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projector’s image. 
i. These buttons function the same as the OSD menus and remote control 
functions. 
•Source List: To switch the source, click on the desired source. 
•Menu: Use to go back to the previous OSD menu, exit and save menu 
settings. 
• When you use the projector control panel or remote control to change the 
OSD menu settings, it may take a while for the web...

35
Please pay attention to the input length and character limitations (including 
character and punctuation restrictions) listed below:
/ > < $ % +    are prohibited.
3The Info page displays the information and status of this projector.
Press exit to go back to the Crestron remote network operation page.
4After pressing the Contact IT Help button, the Title window will display in the 
upper right corner of the screen. You will be able to send messages to 
RoomView™
 software administrators/users who are...

36 Crestron RoomView
From the Crestron RoomView software in the Edit Room page, enter the IP 
Address (or hostname) as shown on the projector’s on-screen display (OSD) 
menu, “05” for IPID, and “41794” for the reserved Crestron control port.
For the Crestron RoomView user guide and information about RoomView settings 
and commands, go to: http://www.crestron.com/products/
roomview_connected_embedded_projectors_devices/resources.asp
Displaying images through EZ Display
Installation for Windows and...

37
Using EZ Display
i.4 to 1 Display: To display up to 4 computers simultaneously, click on the 
location you want to display to. If you only have 2 computers, choose L (left) 
or R (right). To display in full screen mode, click All. You can change the 
location at any time.
ii.Mirror/Extended Display: To duplicate your computer display onto the pro-
jector, click Mirror. To extend your desktop display onto the projector, click 
Extension.
iii.Video/Graphic Display: To display the best image quality, but...

38
3Select WLAN from source list. AP Info page displays.
4Establish WiFi connection with your source device first, and launch EZ Display/
EZ Remote app on your mobile device.
EZ Remote
Launch EZ Remote. You will see the connected device shown on the device list. 
Click it to enable Remote control.
*Skin button is reserved for future feature.
EZ Display
Launch EZ Display and it will scan for and list the devices IP address. When you 
click the device, a passcode is required. Enter the 4 digit number shown...

39 EZ Display: Streaming Doc
To stream your documents, transfer the documents you want from the computer 
to your mobile device and disconnect your mobile device. Documents will be 
organized by their format type.
Select a file to display it wirelessly. Click the Sketch icon to begin drawing and 
annotating your file. Click Save when you are done editing.
EZ Display: Pix Viewer
To display your photos, select Photo Gallery and select your photo. You can also 
draw on it with the Sketch feature.
EZ...