JVC Projector Dla Hd350bu Instructions Manual

 
 
ENGLISH
1
Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

                                  
● Set “COMP.” in the setting menu to “SCART”.(P33 - 12 )
   
● Set “COMP.” in the setting menu to “RGB”.(P33 - 12 )
● For information on compatible input signals, see “Specifications”. (P56)
HDMI 1HDMI 2S-VIDEORS-232CYRVIDEOSYNCCB/PBCR/PRBG
This unit
To RGB video input terminals
RGB video cable(sold separately)R(Red)
B(Blue)
G(Green)(Includes sync signals)
RGB video output...

2Preparation


Installing the Projector and Screen 
While installing, please place this unit and the screen perpendicular to\
 each other. Failing to do so may 
increase trapezoidal distortion. Please refer to “Keystone”. (P36 - 24 )
 
 ● The angle range which can be set for this unit is ±10°.
  
 ● Malfunctions may occur if the angle is not set within the above-mentioned range.
      
1 Installing the projector and screen
      ■ Left/Right position
         * 0% up/down position (center)...

 
 
ENGLISH

Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

2 Adjust such that the projected image is in the center of the screen
● It may be necessary to set “Pixel Adjust” in the setting menu after adjusting the image position. (P36 - 22 )
Determine the distance from the lens to the screen to achieve your desired screen size. 
This unit uses a 2.0x power zoom lens for projection. 
■ Relationship Between Projection Screen Size and Projection Distance
Projection...

3Basic Operation


Projecting Image 
This section describes the basic operations to project input images on t\
he screen. 
Preparation
1 Insert the power plug to the power 
      outlet
2 Turn on the power
    
    ● You can also press the        button on the unit to turn on the power.
                 (P15)
             ● The lens cover will be opened.
3 Project the image
     1 Select input mode
                                        
 ● You can also select the input mode by pressing...

 
 
ENGLISH
5
Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

       Adjust the image size (zoom)
● Every time the LENS button is pressed, the adjustment item will be switched among “Focus”, “Zoom” and “Shift”. 
     FocusZoomShiftLENS                    
      To end
6  Turn off the power
     
● When power off, the lens cover will be closed.
● The power cannot be turned off within approximately 90 seconds
    after it has been turned on. Start operation only...

3Basic Operation
6

Convenient Features during Projection 
You can change the screen size of the projected image or hide the surroun\
ding area of an image for which 
quality at the outer area has deteriorated.
The projected image can be set to a most appropriate screen size
(aspect ratio).
● The screen size can also be set from “Aspect(Video)” of the setting menu.
      (P34 - 14 )
● When PC signals are input, the “Aspect(Computer)” setting will be available  
      instead. (P34 - 15 )
■ Input...

 
 
ENGLISH

Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

2 Mask the image   
    
     1 Display the setting menu
      Select “Input Signal”  “Mask” 
      Set a mask value
Example: 
When the “Mask” value is  
changed from “Off”  “5%”
3 To end 
MENU
MENUExitBACKBackSelectOperate
   0   0   0   06500K
2
Normal
Picture ModeContrastBrightnessColorTintColor Temp.GammaAdvancedLens Aperture
 Picture AdjustNatural
Reset
Video/S-VideoCOMP....

4Settings
8

Setting Menu 
Projected images can be adjusted to a desired view by changing the initi\
al settings.
Example: 
  When changing “Aspect(Video)” from “:” to “16:9”
1 Display the setting menu
2 Select “Input Signal”  “Aspect(Video)”
3  Set to “16:9”
4  To end
MENU
MENUExitBACKBackSelectOperate
   0   0   0   06500K
2
Normal
Picture ModeContrastBrightnessColorTintColor Temp.GammaAdvancedLens Aperture
 Picture AdjustNatural
Reset
4:34:316:9Zoom
ExitMENUBACKBackSelectOperate
Off...

 
 
ENGLISH
9
Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

Item values shown in  are factory settings.
● Items that can be configured differ according to the input signals.
Picture Adjust 
01 Picture Mode
Adjusts the pattern of the projected image.
Cinema 1, Cinema 2, Natural, Stage, Dynamic, User 1, User 2 and User 3.
02 Contrast
Adjusts the contrast of the projected image.
(Black) –50 to 50 (White)
03 Brightness
Adjusts the brightness of the projected image....

4Settings
0

Setting Menu (Continued)
Picture Adjust > Color Temp.
06 Color Temp.
Sets the color temperature of the projected image.
5800KSelect this to give a reddish tinge to the 
image.
Only offset can be set.
6500KSelect this to have a balanced image.
7500KSelect this to give a bluish tinge to the 
image.
9300KSelect this to give a greater bluish tinge 
than 7500K.
High BrightSelect this to get the brightest image.
Custom 1
Gain
(Bright part)
Red(Less red) –255 to 0 (More red)
Green(Less green)...