JVC Th A55 Instructions

8
Getting started
• Do not connect the AC power cord until all other connections have been made.
• Since different components often have different terminal names, carefully read the instructions supplied with the components y ou are going 
to connect.
Connecting a TV
To view pictures and on-screen displa ys, connect the TV to the center unit.
 Distortion of picture may occur when connecting to th e TV via a VCR, or to a TV with a built-in VCR.
 You need to set “MONITOR TYPE” in the PICTURE menu...

Getting started
9
Connecting the FM and AM (MW) antennas
Make sure the antenna conductors do not touch any other terminals, 
connecting cords and power cords. This could cause poor reception.
AM (MW) loop antenna
Setting up supplied AM (MW) loop antenna
Attach the AM (MW) loop to its base by snapping the tabs on the 
loop into the slot on the base.
 
Connecting AM (MW) loop antennaIf reception is poor
Connect an outdoor single vinyl-covered wire antenna (not 
supplied) to the AM EXT terminal. (Keep the...

Getting started
10
Connecting the powered subwoofer
Connect the supplied powered subwoofer (SP-PWA85/SP-PWA55) using the system cord (supplied).
• Connect the system cord by matching the  5 marks on the plugs to the ones on th e center unit and powered subwoofer.
Connecting the satellite speakers
7Speaker layout
When positioning the speakers, to obtain the best possible sound 
from this system you need to place a ll satellite speakers at the same 
distance from the listening position  with the front of...

Getting started
11
Assembling the satellite speakers (TH-A85 only)
Each speaker (except the center speaker) has been divided into two 
parts for shipment. Before connecting the satellite speakers, first 
assemble them by following the procedure below.
Before assembling —
 Prepare a Phillips screwdriver.
 Take care not to drop the stand while assembling; otherwise, it 
may cause damage to the floor or injury.
 Ensure enough space exists for assembly and installation.
 Spread a large, thick cloth on...

Getting started
12
7Connecting the satellite  (front, center, surround) speakers (TH-A85)
Each speaker (SP-THA85F) can be used as a front or surround speaker.
CAUTION
• When you connect (larger) speakers other than the supplied ones,  only use speakers with the same speaker impedance (SPEAKER IM PEDANCE) 
as indicated by the speaker terminals  on the rear of the powered subwoofer.
 DO NOT connect more than one speaker to one speaker terminal.
Surround speakers (SP-THA85F)
Center speaker
(SP-THA85C)...

Getting started
13
7Connecting the satellite  (front, center, surround) speakers (TH-A55)
Be sure to identify each speaker  (SP-THA55C/SP-THA55F/SP-THA55S) and connec t them to the corresponding terminals of the 
powered subwoofer.
CAUTION
• When you connect (larger) speakers other than the supplied ones,  only use speakers with the same speaker impedance (SPEAKER IM PEDANCE) 
as indicated by the speaker terminals  on the rear of the powered subwoofer.
 DO NOT connect more than one speaker to one...

Getting started
14
Connecting to an analog component
You can enjoy the sound of an analog component such as a VCR, TV, or Cassette recorder with this system. Use RCA pin plug cords (not 
supplied) for connection.
NOTE
 If you connect a sound-enhancing device such as a graphic equalizer between the source components and this system, the sound output through this 
system may be distorted.
 When playing a video component such as a VCR;
To listen to the sound, select “AUX” as the source to play. (A
pg....

Getting started
15
Connecting the power cord
Make sure that all connections have been completed, before plugging in the power cords of the center unit and powered subwoofer.
CAUTION
 Disconnect the power cord before cleaning or moving the system.
 Do not touch the power cord with wet hands.
 Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp and pull the plug so as not to damage the cord.
NOTE
 Keep power cords away from other connected cords. The power cords may...

Getting started
16
The remote control makes it easy to use many of the system 
functions from a distance of up to 7 m away.
• You can also use the remote control supplied for this system to 
operate other manufacturers’ TVs ( Apg. 17) and VCRs 
( A pg. 18). 
Putting batteries in the remote control
Before using the remote  control, first put in the 2 supplied batteries.
1Remove the battery 
cover on the back of 
the remote control.
2Insert the batteries.
 Make sure to match polarity: (+) to 
(+) and (–)...

Getting started
17
For TV operations
You can operate your TV using the remote control supplied with 
this system.
• Refer also to the instructio n manuals supplied with your TV.
7To set the manufacturer’s code
You can operate a JVC TV without  setting the remote control 
signal.
1Slide the remote cont rol mode selector 
to TV.
2Press and hold  FTV.
Keep the button pressed until step 4 is finished.
3Press ENTER.
4Press number buttons (1 -9, 0) to enter 
the manufacturer’s code (2 digits).
Examples:
For a...