Kenmore Electric Power Miser 9 Manual

1
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Owner’s Manual
FOR POTABLE WATER HEATING ONLY.
NOT SUITABLE FOR SPACE HEATING.
MODEL NO.
153.329264 38 Gallon Short
153.329265 38 Gallon Short
153.329362 30 Gallon
152.329363 30 Gallon
153.329462 40 Gallon
153.329463 40 Gallon
153.329562 55 Gallon
153.329563 55 Gallon
153.329662 66 Gallon
153.329663 66 Gallon
153.329862 80 Gallon
153.329863 80 Gallon
POWER MISER™ 9
ELECTRIC
WATER HEATER
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A
www.sears.comPRINTED...

2
SAFE INSTALLATION, USE AND SERVICE
Your safety and the safety of others is extremely important in the installation, use and servicing of this water heater.
Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you
and others of a potential injury hazard.  Read and obey all safety messages and instructions throughout this manual.  It is very
important that the meaning of each safety message is understood by you and others who install, use or...

3
GENERAL SAFETY 

4
SAFE INSTALLATION, USE AND SERVICE ........................................................................................................................................ 2
GENERAL SAFETY............................................................................................................................................................................. 3
TABLE OF...

5MAXIMUM FUSE
RECOVERY RATEMINIMUM OR CIRCUIT
MODELGALS.PER HOUR WIRE SIZE*BREAKER
NUMBERGalsLitersDIA.HEIGHT @900F RiseUPPERLOWER(GAUGE)SIZE (AMPS)
153.329264 17.3 3800 3800 12 20
153.329265 25.0 3800 5500 10 30
153.329362 17.3 3800 3800 12 20
153.329363 25.0 3800 5500 10 30
153.329462 17.3 3800 3800 12 20
153.329463 25.0 3800 5500 10 30
153.329562 17.3 3800 3800 12 20
153.329563 25.0 3800 5500 10 30
153.329662 17.3 3800 3800 12 20
153.329663 25.0 3800 5500 10 30
153.329862 17.3 3800 3800 12 20...

6
MATERIALS AND BASIC TOOLS NEEDED
Basic Tools
You may or may not need all of these tools, depending on your
type of installation. These tools can be purchased at your local
Sears store.
Pipe Wrench (2)
Screwdriver
6 Foot Tape or Folding Rule
Garden Hose
Drill
Pipe Dope or Teflon Tape
Additional Tools Needed When Sweat
Soldering
Tubing Cutters or Hacksaw
Propane Torch
Soft Solder
Solder Flux
Emery Cloth
Wire Brushes
SLOT-HEAD SCREWDRIVER
PHILLIPS SCREWDRIVER
DRILL
PIPE DOPE (SQUEEZE TUBE)
USE FOR WATER...

7
Removing the Old Water Heater
1.  Turn “OFF” electrical supply to the water heater.
FIGURE 1.
2.  Turn “OFF” the water supply to the water heater at the water
shut-off valve or water meter.
FIGURE 2.
3.  Attach a hose to the water heater drain valve and put the
other end in a floor drain or outdoors. Open the water  drain
valve. Open a nearby hot water faucet which will relieve
pressure in the water heater and speed draining.
FIGURE 3.
The water passing out of the drain valve may be extremely hot.
To...

8
Mineral buildup or sediment may have accumulated in the old
water heater. This causes the water heater to be much heavier
than normal and this residue, if spilled out, could cause staining.
Facts to Consider About the Location
You should carefully choose an indoor location for the new
water heater, because the placement is a very important
consideration for the safety of the occupants in the building
and for the most economical use of the appliance. This water
heater is not intended for outdoor...

9
Before making the conversion to 5500 watts, check the (1)
power supply . . . must be 240 volts, (2) wiring . . . 10 gauge
AWG @ Type TW, 60°C or equivalent, and (3) Circuit breakers
or fusing . . .capable of 30 amp loading. Also, the installation
must conform with this manual, local codes and electric utility
rules. Failure to comply can result in DEATH, SERIOUS BODILY
INJURY, OR PROPERTY DAMAGE.
      
FIGURE 6.
NOTE: Whether or not the element conversion is made the
model rating plate must be marked....

10
NOTE: To protect against untimely corrosion of hot and cold
water fittings, it is strongly recommended that di-electric
unions or couplings be installed on this water heater when
connected to copper pipe.
1. Look at the top cover of the water heater. The hot water outlet
is marked hot. Put two or three turns of teflon tape around
the threaded end of the threaded-to-sweat coupling and
around both ends of the 3/4” threaded nipple. Using flexible
connectors, connect the hot water pipe to the hot water...