Kenwood Dvt 6200 Instruction Manual

							11
Preparations
DVT-6200 (EN/K,E,X)
System Connections
Caution:
Do not plug in the power lead until all connec-
tions are completed.Make connections as shown below.
When connecting the related system components, refer also
to the instruction manuals of the related components.
CautionBe sure to adhere followings. Or proper ventilation will be blocked causing damage or
fire hazard.
÷Do not place any objects impairing heat radiation onto the top of unit.
÷Leave a space around the unit (from the largest outside dimension including pro-
jection) equal or greater than, shown below.
Top panel : 50 cm          Side panel : 10 cm           Back panel : 10 cmMalfunction of microcomputerIf operation is not possible or erroneous
display appears even though all connec-
tions have been made properly, reset the
microcomputer referring to “In case of
difficulty”.Y
Loudspeakers
Front
speaker L SubwooferSurround
speaker
L
Front
speaker R Surround
speaker
R
Center speakerExcessive insertion of the cable
can cause defective contact.
NoteNoteNote
123
&/+03.7.8, 11:05 AM Page 11EPCF
1BHF.BLFS
+11$
 
						

							12
Preparations
DVT-6200 (EN/K,E,X)
AM loop antenna
FM antenna
AM loop antenna connection
The supplied antenna is
for indoor use. Place it as
far as possible from the
main system, TV set,
speaker cords and power
cord, and set it to a direc-
tion which provides the
best reception.
FM indoor antenna connection
The accessory antenna is for
temporary indoor use only.
For stable signal reception
we recommend using an out-
door antenna. Remove the
indoor antenna if you con-
nect one outdoors.1Connect to the antenna terminal.
2Locate the position providing good
reception condition.
3Fix the antenna.
FM outdoor antenna
(commercially available)Lead the 75 Ω coaxial
cable connected to the
FM outdoor antenna
into the room and con-
nect it to the FM 75 Ω
terminal.
Caution : Read this page carefully to ensure safe operation.
Black
System Connections
Example for some areas
Example for some areas
(For U.S.A.)
(For Europe and Australia)
&/+03.7.8, 11:05 AM Page 12EPCF
1BHF.BLFS
+11$
 
						

							13
Preparations
DVT-6200 (EN/K,E,X)
Connecting to a TV
Connecting to a Satellite Tuner
COMPONENT Video cord
*COMPOSITE Video cord
 (accessory)
S-Video cord
Audio cord COMPOSITE
video cord **COMPONENT connection corresponds only to some areas.
When the TV has a COMPONENT terminal, the DVD image will be played
back with higher picture quality in case of COMPONENT connection.
Connect the S-video or the COMPOSITE video cable also in this case.
Select the scanning method of the Component Video output using the
PROGRESSIVE (ACTIVE EQ.)  key on the front panel.
NoteNoteNote
*For Europe only
If your TV set has a SCART terminal,
connect the accessory SCART plug to
the SCART terminal of the TV and
connect the COMPOSITE video cord. TV
Satellite tuner
System Connections
NoteNoteNote
**0nly for
some areas.
Depressed and keep pressing the key. Each time
the key is being held down, the setting changes
as follows.
1ON
2OFF
ON: When progressive scanning is unavailable with certain discs, the scanning
method is switched automatically to interlaced scanning. When the scanning
method is changed, the scanning status will be displayed for a few seconds.
OFF: Scanning method is fixed at interlaced scanning.
Example for some areasThe S-Video output terminal of this unit is only for output of the built-in
DVD player. The output of equipment connected to VCR, CABLE/SAT is put
out as a composite signal.
&/+03.7.8, 11:05 AM Page 13EPCF
1BHF.BLFS
+11$
 
						

							14
Preparations
DVT-6200 (EN/K,E,X)
Connecting to Audio video equipments
Audio cords
COMPOSITE video cords
Audio cords
Play Record
RecordPlay
DTS disclaimer clause
DTS Digital Surround™ is a discrete 5.1 channel digital audio format available on CD, LD, and DVD software which
consequently cannot be decoded and played back inside most CD, LD, or DVD players. For this reason, when DTS-
encoded software is played back through the analog outputs of the CD, LD, or DVD player, excessive noise will be
exhibited. To avoid possible damage to the audio system, proper precautions should be taken by the consumer if the
analog outputs are connected directly to an amplification system. To enjoy DTS Digital Surround™ playback, an external
5.1 channel DTS Digital Surround™ decoder system must be connected to the digital output (S/P DIF, AES/EBU, or
TosLink) of the CD, LD or DVD player.
This unit is equipped with DTS Digital Surround™ decoder.
NoteNoteNote
System Connections
Recording from the VCR OUT terminal of this unit is only possible when the LISTEN MODE is set to STEREO.
&/+03.7.8, 11:05 AM Page 14EPCF
1BHF.BLFS
+11$
 
						

							15
Preparations
DVT-6200 (EN/K,E,X)
23
45 6 7 890!@ # $ 1
PROG. (Program) indicator
PLAY/PAUSE indicator
IN/OUT status indicator
L: Left speaker
C: Center speaker
R: Right speaker
LS : Left surround speaker
LFE : Low Frequency Effect
RS : Right surround speaker
Display
1POWER switch^
2STANDBY indicator
3Disc tray‚
4OPEN/CLOSE (0) key‚
5PLAY/PAUSE (6) key‚
6STOP (7) key‚
7SKIP (
4 44 4
4,
¢ ¢¢ ¢
¢) keysq
8BAND keyfl9INPUT key›
0LISTEN MODE keyª
!ACTIVE EQ. key (for Europe and Australia)
º
PROGRESSIVE / ACTIVE EQ. key (for U.S.A.)
#
@DIMMER key
#VOLUME CONTROL knob›
$PHONES jack› CD indicator
DVD indicator
VCD indicator
MP3 indicatorREPEAT indicator
A-B REPEAT indicator
FOLDER indicator
Character
information
display section
Controls and indicators
TITLE indicator
TRACK indicator
CHAP (CHAPTER)
indicatorST (Stereo) indicator
TUNED indicator
RDS indicator
(only for Europe)
Standby mode
While the standby indicator is lit, a small amount of power in supplied to the system to back up the memory.
This is called standby mode. Under the condition, the system can be turned ON by the remote control unit.
DOLBY DIGITAL indicator
DOLBY Pro Logic II indicator
DTS indicator
RANDOM indicator
CAUTION
The power in this equipment will not be completely cut off from the AC wall outlet when the main switch is turned OFF.
The display brightness of the main
unit can be changed.
Switching as shown below is done each time the DIMMER key
on the remote control is pressed.
1Bright
2Dim 1
3Dim 2DIMMER functionDIMMER
This lights when an MP3 or
a JPEG disc is set.
&/+03.7.8, 11:05 AM Page 15EPCF
1BHF.BLFS
+11$
 
						

							16
Preparations
DVT-6200 (EN/K,E,X)
The keys on the remote control unit with the same names as on the
main unit have the same function as the keys on the main unit.
1REPEAT keyt
A-B (Repeat) keyt
RANDOM keyr
2Numeric keys‡
3PGM (Program) keyu
4CLEAR keyi
5ANGLE keyr
RDS DISP. (for Europe only)  key
°
PTY (for Europe only)  key·
6TOP MENU/INTRO SCAN key
‚y
7Cursor Up (5), Down (∞), Left
(2) and Right (3) keys)
ENTER/PRESET key)
8RETURN key(
9P.CALL /4,¢ (Skip) keys
flq
TUNING/ 1,¡ (Search) keys
flq
08 (pause) key‚
3 (play) key‚
!SUBTITLE keye
AUDIO keye
SLOW  keyw
STEP keyq
Loading batteries
2 Insert batteries.3 Close the cover. 1 Remove the cover.
÷Insert two R6 (“AA”-size) batteries fol-
lowing the polarity indications.
Operation
Insert the power plug into a power outlet, press the POWER
switch of the main unit to ON, then press the POWER key
on the remote control.
÷When pressing more than one remote control keys successively,
press the keys securely by leaving an interval of 1 second or more
between pressing of keys.
Operating range (approx.)Remote sensor
1. The provided batteries are intended for use in operation checking, and their service life may be short.
2. When the remote controllable distance becomes short, replace both of the batteries with new ones.
3. If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote sensor, malfunction
may occur. In such a case, change the installation position to avoid malfunction.
Model : RC-R0310E (for Europe)
RC-R0310 (for other countries)
Infrared ray system
Operation of remote control unit
NotesNotesNotes
1
2
3
5
7
8
9
0
!
@
#
$
™ ¡ ) ( * & ^ %
4
6@Speaker select keys¤
FRONT key
CENTER key
REAR key
SW (Subwoofer) key
#LISTEN MODE keyª
ACTIVE EQ./SET UP keyº
$MUTE key›
%POWER key*
^INPUT SELECTOR keys›
DVD/CD key
TUNER/BAND key
VCR key
CABLE/SAT. (Satellite) key
&BOOK MARK keyy
*MENU/P.B.C. key)
(ON SCREEN keyw
)7 (stop) /AUTO/MONO key
fl‚
¡TRIM
Up (5), Down (∞) keysª
™VOLUME
Up (5), Down (∞) keys›
30º30º
6m
12
&/+03.7.8, 11:05 AM Page 16EPCF
1BHF.BLFS
+11$
 
						

							17
Preparations
DVT-6200 (EN/K,E,X)
&/+03.7.8, 11:05 AM Page 17EPCF
1BHF.BLFS
+11$
 
						

							DVT-6200 (EN/K,E,X)
Set Up functions18
Preparations
Set up menu
Set Up functions
Preparation for Set Up
GENERAL SETUP
TV DISPLAY
This sets the screen size (4:3 or 16:9 aspect ratio) according to the connected TV.
 NORMAL/PS (Pan Scan)
NORMAL/LB (Letter Box)
Choose this setting if you want the movie to fill the entire screen of your TV. You wont see part of the picture 
(particularly the right and left edge).
  Some disc produced in a wide screen format cant be cropped in this fashion, which means the black bars 
would appear at the top and the bottom of the screen.
PIC MODE
AUTO
OSD LANG
ANGLE MARK
CAPTION (NTSC only)
SCR SAVER
FILM
VIDEO
SMART
Choose this setting to reproduce  progressive and interlaced materials with limited motion. 
SSMART
Choose this setting to reproduce  progressive and interlaced materials with motion (motion adaptiv 
deinterlacing). Choose this setting if you would prefer to see movies in their original aspect ratio. You will see the entire frame 
of the movie, but it will occupy a smaller portion of the screen. This setting may result in the movie appearing 
with black bars at the top and bottom of the screen.
WIDE
Choose this setting if your DVD player is connected to a widescreen TV.
The picture quality is adjusted automatically.
Choose this setting to reproduce the picture quality of FILM material.
Choose this setting to reproduce the picture quality of VIDEO material.
This switches the language for the on-screen display.  When this is set to ON, the ANGLE mark (      ) will be displayed when a multiangle scene is reached during 
playback of a DVD.
This switches the CLOSED CAPTION ON or OFF.
“closed caption” is a subtitle display system developed for hearing-impaired persons, but it is also a very 
effective system for learning foreign languages. When your TV is compatible with “closed caption” and you 
select ON, you can use the CLOSED CAPTION function.
This switches the screen saver ON or OFF.
When SCR SAVER is ON, the screen saver function will operate after approx. 3 minutes have passed with a still picture 
(display of KENWOOD).This adjusts the screen quality according to the material being played back.
The SETUP functions are the following diverse functions. Please change them according to your use environment.


 ( OFF )
 ( OFF )
 ( OFF )
 ( ENGLISH )
The items in              are the initial set values.
1Turn on  the POWER.
MAIN UNIT
+
REMOTE
2Set TV Format according to the connected TV type.
(Initial Settings 0)While no disc is inserted, hold the DIMMER key
on the main unit depressed and press the SUB-
TITLE key on the remote control. Each time the
SUBTITLE key is pressed, the setting changes
as follows.
1MULTI (NTSC/PAL switchable)
2NTSC
3PAL
&/+03.7.8, 11:06 AM Page 18EPCF
1BHF.BLFS
+11$
 
						

							DVT-6200 (EN/K,E,X)
Set Up functions19
Preparations
AUDIO SETUP
DYNAMIC
At the time of Dolby digital DVD playback, the differece of the maximum volume and the minimun volume are 
compressed. Adjustment is possible in 8 steps, and the range is largest (compression ratio 0) at the time of OFF and 
smallest (large compression ratio) at the time of FULL. ( OFF )
Choose S-VIDEO in case of connection to the S-VIDEO terminals on the rear, choose RGB in case of connection to 
the AV terminal or choose COMPONENT in case of connection to COMPONENT terminal. Output will not be made to 
the not selected terminals. (#$) ( S-VIDEO )
Choose the language for the AUDIO output.
Choose the language for SUB TITLE.
Choose the language for the menu recorded on the DISC.
This resets all settings, except for PARENTAL and PASSWORD, to the factory defaults.
PREFERENCES
VIDEO OUTPUT (only for some areas) 
AUDIO
SUB TITLE
DISC MENU
PARENTAL
This can restrict playback of adult-oriented DVD discs that you do not want to be seen by children.
However, even when a DVD disc is marked Adult-oriented or so on the label, its viewing cannot be 
restricted unless the restriction level is recorded in the disc itself. (  8  )
Parental lock level;
Level 8: All DVDs can be played back.(Factory preset)
Level 7 to 2: DVDs  for general audiences/children can be played back. (DVDs for adults are prohibited.) 
Level 1: DVDs for children can be played back. (DVDs for adults/general audiences are prohibited.)
PASSWORD
The password for PARENTAL setting, change, cancellation, etc. is set.
The password set at the time of shipping from the factory is 0000.
DEFAULTS
 ( ENGLISH  *)
 ( ENGLISH  *)
 ( ENGLISH  *)
When the language marked with an asterisk (*) is specified by the disc, that specification has priority.
How to use the RETURN key
When the RETURN key is
pressed, the display returns
to the MAIN PAGE.
&/+03.7.8, 11:06 AM Page 19EPCF
1BHF.BLFS
+11$
 
						

							DVT-6200 (EN/K,E,X)
Set Up functions20
Preparations
 Select TV Display Select Picture Mode
3Press Cursor up/down (5/∞) keys on the remote
to select TV DISPLAY, then press the Cursor
right (3) key to access the sub features 1During stop mode, press MENU key on the re-
mote.
2Press Cursor up/down (5/∞) keys on the re-
mote to select the GENERAL SETUP, then
press the ENTER key to access the sub fea-
tures
4Press Cursor up/down (5/∞) keys on the remote
to select TV Display type, then press the ENTER
key.
5Press Cursor left (2) key on the remote to return
to previous menu.
6Press Cursor up/down (5/∞) keys on the remote
to select MAIN PAGE, then press the ENTER key.
7Press Cursor up/down (5/∞) keys on the remote
to select EXIT SETUP, then press the ENTER key.3Press Cursor up/down (5/∞) keys on the remote
to select PIC MODE, then press the Cursor right
(3) key to access the sub features 1During stop mode, press MENU key on the re-
mote.
2Press Cursor up/down (5/∞) keys on the re-
mote to select the GENERAL SETUP, then
press the ENTER key to access the sub fea-
tures
4Press Cursor up/down (5/∞) keys on the remote
to select specific mode, then press the ENTER
key.
7Press Cursor up/down (5/∞) keys on the remote
to select EXIT SETUP, then press the ENTER key.
5Press Cursor left (2) key on the remote to return
to previous menu.
6Press Cursor up/down (5/∞) keys on the remote
to select MAIN PAGE, then press the ENTER key. Please refer to pages 18 and 19 for setup.
&/+03.7.8, 11:06 AM Page 20EPCF
1BHF.BLFS
+11$