Keurig K75 Clba Manual

Owner’s manual
Keurig® K- Cup® K70/K75 Plati\fum Brewer 

2
IMPORTANT SAFEGUARDS  Safe Operation & Use
When using electrical appliances, basic 
safety precautions should be followed, 
including the following:
 1. Read all instructions before using.
 2. Do not touch hot sur faces. Use handles  
and knobs when available.
 3. This appliance must be properly 
installed and located in accordance 
with these instructions before it is used.
 4. The use of accessor y attachments 
not recommended by the appliance 
manufacturer may result in fire, 
electrical shock or...

3
TABLE OF CONTENTS
KEURIG® GOURME T SINGLE CUP HOME BRE WING SYSTEM
K70/K75 Platinum Brewer — Using Your Brewer
SeT-uP  
H elpful Hints
 
 ........................................................................\
................
4 
Unpacking
 

........................................................................\
....................
4 
Features
 

........................................................................\
.......................
5
SecTIon  1   —  SET-UP & FIRST BRE W  
Set-Up &...

Set-Up
helpful hints 
 1. Plug brewer into its own grounded outlet.  If the electric circuit is overloaded with other  
appliances, your brewer may not function   
properly. The brewer should be operated on   
its own circuit, separate from other appliances.
 2.  Keep your brewer turned “ON.”   To brew a fresh cup of coffee, tea or hot cocoa  
any time you want, keep your brewer turned 
“ON” all the time. However, the brewer is fully  programmable so you can set it to turn on and off automatically to...

5
Features  K70/K75 Platinum Brewer
 A. Water Reser voir Lid B. Easy-Fill Lid C. MA X FILL D. Water Reser voir E. Water Reser voir  
Lock Tab Slot
K70/K75 Platinum Brewer Controls 
 
and Indicators
a
D
c
B
e
K
n
M
L
J
o
G
h
v
T
u
rF
I
Q
P
S
 R. LCD Control Center S. Left Button T. Right Button U. MENU Button V. BRE W Button
 F. Handle G. Funnel H. K-Cup® Pack Holder   
(F and G are the K-Cup® 
Pack Holder Assembly) 
 I. Lid
 J. K-Cup® Pack   
Assembly Housing
 K. Housing
 L. Drip Tray Plate M. Dr i p  Tr...

Setting up Your Brewer
 1. Unwrap cord and plug the brewer into a grounded outlet. Remove all pieces of   
packing tape and clear plastic sticker from   
LCD Control Center.
 2. Place a large mug (10 oz. minimum) on the Drip  Tr a y  P l a t e .
 3. Remove the Water Reser voir from brewer by  first removing Lid from the Water Reser voir   
(fig. 1), then lifting the Water Reser voir straight 
up and toward front of brewer (may be tight),   
(fig. 2 A). Rinse with fresh water.
 4. Fill Water Reser voir...

 5. Place a K-Cup® pack in the K-Cup® Pack 
Holder (fig. 6). 
CAUTION:  There are two sharp 
needles that puncture the K-Cup® pack, one 
above the K-Cup® Pack Holder and the other in 
the bottom of the K-Cup® Pack Holder. To avoid 
risk of injur y, do not put your fingers in the  K-Cup
® Pack Assembly Housing.
 

6.
 
Lower the Handle to close the Lid over the  
K-Cup® Pack Holder. (When it is closed 
completely, the LCD Control Center will  indicate “RE ADY TO BRE W.” The Left and 
Right Buttons will be...

8
 c. Once the brew size is chosen, press the  
BRE W Button. The BRE W Button will stop  flashing and the Left and Right Buttons will   
no longer be illuminated.  
 7. The LCD Control Center will indicate 
“BRE WING” and the selected brew size icon  will be lit (fig. 8). 
CAUTION:  There is extremely 
hot water in the K-Cup® Pack Holder during the 
brew process. To avoid risk of injur y, do not lift 
the Handle or open the K-Cup
® Pack Assembly 
Housing during the brew process.
 8. There may be a shor...

9
The Water Reser voir can be filled in two ways. 
 
1.
 Open the Easy-Fill Lid and pour water directly into the Water Reser voir   
while it is still attached to the brewer. Fill with water to and not beyond 
the MA X FILL line. Close the lid. The entire Water Reser voir Lid may be 
removed completely, if preferred.
 2. Remove the Water Reser voir from brewer by first removing Lid from the  Water Reser voir, then lifting the Water Reser voir straight up and toward front of brewer. Fill with water to and...

10
SECTION 2  Controls & Indicators (LCD Control Center)
Setting the clock
Setting the clock is optional. When the clock is set, the time will appear in the 
LCD Control Center. 
NOTE:  You must set the clock if you will be using the Auto 
On/Off Time programming feature.
 

1.
 Press the MENU Button.
 2. The word “OFF” will appear at the top of the LCD Control Center to indicate that the clock is not set (fig. 10). The programming options will appear on the LCD Control Center with a 
small arrow...