Knoll Systems Ht201 Projector Specifications

							        
      HT201/HT211 
 
Users Manual v1.1 
 
 
 
 
 
 
 
    Includes PLUS CORPORATION micro light engine 
 
Complies with part 15 of the FCC rules. Operation is subject to:  
1. This device may not cause harmful interference 
2. This device must accept any interference received       
      including interference that may cause undesired operation. 
 
 
 
 
 
 
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT 
REMOVE THE COVER, NO USER SERVICEABLE PARTS INSIDE. 
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 
 
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO  
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 
 
 
 1 
						

							IMPORTANT SAFEGUARDS 
These safety instructions are to ensure the long life of your projector and to prevent fire and 
shock.  Please read them carefully and heed all warnings. 
Installation 
• For best results, use your projector in a darkened room. 
• Place the projector on a flat, level surface in a dry area away from dust and moisture or hang it 
from the ceiling with an approved mount kit. 
• Do not place your projector in direct sunlight, near heaters or heat radiating applian\
ces. 
• Exposure to direct sunlight, smoke or steam can harm internal components. 
• Handle your projector carefully.  Dropping or jarring can damage internal components. 
• Do not place heavy objects on top of the projector. 
• If installing the projector in the ceiling: 
− The ceiling must be strong enough to support the projector.  
− The installation must be in accordance with any local building codes. 
− Qualified Knöll dealer personnel must install the projector. 
 
Power Supply 
• The Projector is designed to operate on a power supply of 100-120 or 220-240 V 50/60 Hz 
AC.  Ensure the mains power fits this requirement before attempting to use your Projector. 
• Handle the power cable carefully and avoid excessive bending.  A damaged cord can cause 
electric shock or fire. 
• If the projector is not to be used for an extended period of time, disconnect the plug from the 
power outlet. 
 
Cleaning 
• Unplug the projector before cleaning. 
• Clean the cabinet periodically with a damp cloth.  If heavily soiled, use a mild detergent.  
Never use strong detergents or solvents such as alcohol or thinner. 
• Use a blower or lens cloth to clean the lens and be careful not to scrat\
ch the lens. 
 
Lamp Replacement 
• Be sure to replace the lamp when the Status light comes on.  If you continue to use the lamp 
after 1000 hours of use, the lamp will turn off. 
• Allow a minimum of one minute to elapse between turning the lamp off and on.  High 
voltage is applied to the lamp immediately when the power is turned on. Turning the power 
off and quickly back on may shorten the lamp life lamp and result in damage to the projector. 
 
Fire and Shock Precautions 
• Ensure there is sufficient ventilation and the vents are unobstructed to prevent heat buildup 
inside the Projector. Allow at least 10cm (3”) of space between your projector and a wall. 
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector.  
Do not attempt to retrieve any objects that might fall into your projector.  Do not insert any 
metal objects such as a wire or screwdriver into your projector.  If something should fall into 
your projector, disconnect it immediately and have the object removed by a qualified Knöll 
service person. 
• Do not place any liquids on top of your projector. 
• Do not look into the lens while the projector is on.  Serious eye damage\
 could result. 
 2 
						

							Table of Contents 
2 IMPORTANT SAFETY INFORMATION 
3 Table of contents 
 
4 Basic information  
4 Features 
5 Remote control 
 
6 Terminal connections 
6 Projector part identification 
7 Projector positioning 
8 Connecting video equipment 
9 Connecting component video 
10 Connecting a PC or Macintosh 
12 Using the remote control as a computer mouse 
12 D-Sub pin assignments 
 
13 Using the projector 
13 Selecting the input source 
14 Turning the projector off 
14 Changing the computer’s video resolution 
15 Freezing the picture 
16 Enlarging the picture 
16 Menu operations 
16 Selecting ceiling, floor front or rear projection 
17 Selecting input mode to component 
17 Changing aspect ratios  
17 Adjusting the image from the source connected to the RGB input 
19 Adjusting the picture elements 
19 Manual adjustment of computer images 
19 Checking the hours of lamp usage 
 
20 Specifications 
21 Troubleshooting 
22 Status Indicator lamps 
22 Replacing lamp housing 
23 Lamp replacment procedure 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3 
						

							Basic Information 
 
Congratulations On Your Purchase of the Knöll Projector! 
The Knöll DLP is one of the very best projectors available today.  It enables you to project 
precise images up to 200 inches across (measured diagonally) from your PC or Macintosh 
computer (desktop or notebook), VCR, document camera, laser disc player, DVD player, etc. 
The projector can be placed on a tabletop or cart, or permanently mounted on the ceiling.  You 
may use the projector to project images from behind the screen.  The supplied remote control can 
be used as wireless control and with the supplied mouse receiver to operate the mouse functions 
on your PC or Macintosh. 
 
 
The features youll enjoy… 
• Compatible with following various color systems: 
− NTSC (U.S. and Canada standard) 
− PAL (Western Europe and Australia/New Zealand standard) 
− SECAM (France and Eastern Europe standard) 
− NTSC4.43 (Middle East country standard) 
• Superior brightness of 800 ANSI lumens with small size and 1.3 kilograms 
The DMD and our own optical design interact in a geometric effect to increase the light usage 
efficiency.  Now you can reproduce the 3 basic colors (RGB) required for color reproduction 
on a single DMD.  That means superior brightness, smaller size and lighter weight. 
• Sharp, clear images 
There is no RGB color separation, and the spaces between the individual \
pixels are not 
noticeable.  That means sharp and clear reproduction of small characters and figures.  Take a 
closer look and notice the difference in quality! 
• Outstanding beauty when reproducing DVDs and other high picture-quality \
information 
sources 
Faithful gray scale reproduction makes for more natural image displays. DVD and other high 
quality image sources bring out the true display capacity of the Projector. 
• Screen not distorted to a trapezoid (keystoning) when projecting to the height of the line 
of vision 
Because the projection position is already set to the height of the line of vision, there is no 
distortion of the screen to a trapezoid. Keystone is variable, centered at 17.3 degrees. 
• Fully compatible with true XGA using advanced intelligent compression te\
chnology 
The advanced intelligent compression technology of the HT211 enables it to present clear 
XGA images without any line omission. The HT201 presents clear S-VGA images. 
• The remote control can be used to operate your PC or Macintosh when the \
supplied 
remote mouse receiver is connected. 
 
 
 
 
 
 
 
 
 
 4 
						

							Remote Control 
Inserting the 
batteries 
1) Press firmly and 
slide the battery 
cover off. 
2) Insert the 
supplied two 
batteries (size 
AAA).  Ensure 
that the polarities 
(+ and -) of the 
batteries are 
aligned correctly. 
Always replace 
batteries with 
fresh alkaline 
type. 
3) Slip the cover 
back over the 
batteries until it 
snaps into place. 
 
Notes 
• If the remote 
control gets wet, 
wipe it dry 
immediately. 
• Avoid excessive heat and humidity. 
• If you will not be using the remote control for a long time, remove the batteries. 
• Do not mix new and old or different types of batteries. 
• There are operations that can only be carried out by remote control. Handle the remote control 
carefully. 
 
Remote control effective range 
Each side of the projector has a remote sensor.  The controllable range is 50 degrees horizontally 
and 30 degrees vertically relative to a line that is at a right angle to the remote sensor.  And the 
distance between the point of the remote control and remote sensor must be no more than four to 
five meters (about 15’). 
 
 
 
 
 
 
 
. 
 
 5 
						

							Terminal Connection Panel 
 
    
 
Projector Part Identification 
 
 
 
 
 
 
 
 
 
 
Installation 
The distance from the projector lens to the screen determines to the size of the projected 
image, therefore, you need to consider the place where you set up the proj\
ector and 
screen before making connections.  You also need to consider the screen size and height \
of the unit and screen as other important factors. 
 
Tip: Although not advised, a non-glossy wall may be used as a substitute for a screen. 
 
WARNING: Carrying The Projector 
• Ensure all cables connecting to the projector are disconnected before moving the 
projector.  When moving the projector, cover the lens with the sliding cap. 
• Only use your Projector on a solid flat level surface.  If the projector\
 falls to the 
floor, you can be injured and the projector severely damaged. 
• Do not use the Projector where temperatures vary greatly.  The projector must be 
used at temperatures between 5 degree Celsius (41 degree Fahrenheit) and 35 
degree Celsius (95 degree Fahrenheit). 
• Do not expose the Projector to moisture, dust, or smoke.  This will harm the 
screen image. 
• Ensure that you have adequate ventilation around your Projector to allow\
 heat 
dissipation.  Do not cover the vents on the bottom or the side of the projector. 
 
 
 
 
 
 6 
						

							Projector Positioning 
The projected image becomes larger as the distance between the unit and screen 
increases.  The minimum image size is about 36 inches (93cm) diagonally at a distance of 
about 1.2m (3.9 feet) and the maximum size is about 200 inches (508cm) at a distance of 
6.8m (22.3 feet) from the screen. The HT201 and HT211 do not have zoom capability so 
they must be positioned at the exact distance from the screen.] 
 
         Width 
 
 
                 Diagonal 
                  Screen          Height 
         Size 
 
       17.3 degrees 
              
 
 
 
 
Use the following information to position the projector. Horizontally the projector needs 
to be positions with the lens-centered left to right 
 
 
Projection Distance 4:3 Video Screen 
Screen Diagonal 72” 78” 84” 100” 120” 160” 200” 
Projection 
Distance 96.4 104.4112.4133.8160.6214.1 267.6
 Image Drop 
Or Rise 8.0 8.6 9.3 11.1 13.3 17.7 22.2 
 
Projection distance to screen is 1.338 x screen diagonal size (4:3 screens) 
Drop or rise is 0.111 x screen diagonal size (4:3 screens) 
 
Projection Distance 16:9 Video Screen 
 Screen Diagonal 88.25 103 110 122.5 146.75165.25 220.25
 Projection  
Distance 128.5 150.1160.2 178.4 213.7 240.7 320.8 
 
Projection distance is 1.457 x screen diagonal size (16:9) 
. 
 
 7 
						

							Connecting Video Equipment 
You can connect a document camera, 
VCR, laser disc player, and DVD player, 
etc. 
Connecting to the VIDEO IN 
VIDEO/S-VIDEO JACKS 
You can connect up to two pieces of 
video equipment to the VIDEO IN 
jacks following the illustration below.  
Two types of connections can be 
made.  Connect either using the 
cables indicated in dotted lines or 
those in gray as shown in the drawing 
below. 
• You can switch the input source 
(picture) to VIDEO or S-VIDEO 
even if you connect more than one 
piece of equipment.  S-VIDEO 
connection provides more vivid 
color and higher resolution 
compared to VIDEO connection. 
• You can output the sound of one 
component through the unit 
speaker even when two 
components are connected. 
 
Before connecting 
• Turn off the components that are to 
be connected. 
• The unit and computer will be 
turned on in Using the Projector.  
Do not turn on either the computer 
or unit until you read this section. 
• Please also refer to the manual of 
the video component to be 
connected. 
 
 
 
 
 
 
 
 
 
 
 8 
						

							Connecting Component Video Equipment withYCbCr output jacks to the 
RGB IN connector 
You can also connect the video 
component to the RGB IN connector, if 
the video component has the component 
video (YCbCr) signal jacks.  This 
connection may provide a better picture 
quality than the connections on page 8. 
• You can switch the input source to 
VIDEO, S-VIDEO, or RGB. 
• The AUDIO IN jack is for equipment 
connected to the RGB IN connector. 
 
Before connecting 
• Turn off the components that are to be 
connected. 
• The projector and computer will be 
turned on in Using the Projector.  
Do not turn on either the computer or 
unit until you read this section. 
• Please also refer to the manual of the 
video component to be connected. 
 
 
If you are connecting a 5 wire BNC cable 
to a 15 pin D-sub, you may need three 
21-131-0 BNC to RCA adaptors.  
Connect the 15 pin D-sub into the 
projector. Connect the red BNC to the Cr 
output. Connect the green BNC to the Y 
output. Connect the blue BNC to the Cb 
output. 
 
The remaining black and gray BNC 
connectors are not used in this case. 
When initially displaying component 
video the color may require adjustment. 
To adjust the color, using the remote to 
             the “Image Adjust Menu” and adjust  
             the “Hue” Cr and Cb (red and blue) as 
              required.  
 
 
 
. 
 
 
 9 
						

							Connecting a PC or Macintosh 
Connecting a PC or Macintosh to the Projector enables computer images for impressive presentations. 
• The following display standards are supported by the HT211 (HT201 may not support some of 
the higher resolutions): 
VGA 640x480 for graphics  VGA 640x400 for graphics XGA 1024x768 
VGA 640x350 for graphics  VGA 720x400 for text  Mac  1024X768 
VGA 720x350 for text  SuperVGA 800x600 
Macintosh at 640x480  Macintosh at 832x624 
• If your PC 
does not 
support XGA 
you will need 
to install a 
XGA graphics 
board.  Consult 
your 
computers 
owners 
manual for 
your XGA 
configuration.  
If you need to 
install a new 
board, refer to 
the manual 
supplied with 
your new 
graphics board 
for installation 
instructions. 
Notes 
• Refer to the 
owners 
manual 
supplied with 
your computer 
for more 
information 
about the 
computer 
video output 
requirements and any special identification or configuring required by the projector image and monitor. 
• Some Macintosh PowerBooks may need to set the mirroring to off to output 800x600 dot signals.  
Please consult your PowerBook manual or computer dealer for details. 
 
Before connecting 
• Turn off the components that are to be connected. 
• The projector and computer will be turned on in Using the Projector on page 13.  Do not 
turn on either the computer or unit until you read this section. 
• Please also refer to the manual of the video component to be connected. 
 
 
PowerBook Connection Depending on the model of your PowerBook, the additional Apple 
video cable adaptor may be required with the above connection. 
 10