Kodak C135 User Manual

Using an EYE-FI Card
www.kodak.com/go/support
 44
Other EYE-FI Information
■It’s critical that you disable (do not turn on) Endless Memory Mode in 
EYE-FI Center Software.
■As of December 2010, EYE-FI Cards are permitted only in the countries and 
regions in which they were purchased. You may be held liable due to local 
restrictions.
■The EYE-FI Card has a wireless LAN function. Do not insert the EYE-FI Card where 
wireless LAN is prohibited, such as while aboard an airplane or in a hospital.
■Even when...

45www.kodak.com/go/support
9Troubleshooting
Camera problems
StatusSolution
Camera does not 
turn on■Make sure the batteries are installed correctly (see page 3).
■Make sure batteries are new. If batteries are rechargeable, make 
sure they are fully charged (see charger documentation).
Camera does not turn 
off
Camera buttons and 
controls do not 
function
Condensation on the 
lens or LCD.Condensation may occur when the camera is subjected to 
temperature or humidity changes. To correct, turn off the...

Troubleshooting
www.kodak.com/go/support
 46
Battery life is short■Make sure the correct battery type is installed (see page 51).
■Insert new/charged batteries (see page 3).
■See Extending battery life, page 54.
■Adjust LCD Brightness (see page 36).
■Turn off the Eye-Fi feature when not in use (see page 41).
Cannot find the 
desired picture/video■To view pictures stored on a memory card, see page 22.
You cannot take a 
picture■Turn the camera off, then on again.
■Depress the Shutter button all the way...

47www.kodak.com/go/support Troubleshooting
Computer/connectivity problems
Picture quality problems
StatusSolution
Computer does not 
communicate with 
the camera■Turn off the camera, then turn it back on.
■Make sure the batteries are charged and installed correctly (see 
page 3).
■Make sure the KODAK Camera USB Cable, Micro B / 5-Pin is 
connected to the camera and directly to the computer (not 
through a USB hub). See page 7. Then turn on the camera.
IMPORTANT: Use only the cable included with this...

Troubleshooting
www.kodak.com/go/support
 48
Direct printing (PICTBRIDGE enabled printer) problems
EYE-FI problems
Underwater videos 
are off-color.Use Underwater mode (see page 14).
Status Solution
The Direct printing 
menu interface turns 
off■Press any camera button to redisplay the menu.
Cannot print pictures■Make sure there is a connection between the camera and the 
printer (see page 39).
■Make sure the printer and the camera have power.
Camera or printer 
displays an error 
message■Follow the...

49www.kodak.com/go/support Troubleshooting
Getting help on the Web
EYE-FI Card gets 
warm.■This is normal.
Camera battery life is 
shorter.■Battery life is reduced when using an EYE-FI Card.
Transferring pictures is 
slow using the EYE-FI 
Card.■For the best reception when transferring pictures to a computer 
or mobile device, the rear of the camera should face the Wi-Fi 
access point.
Get support for your product (FAQs, troubleshooting 
information, arrange for repairs,...

www.kodak.com/go/support 50
10Appendix
Camera specifications
CCD—1/2.3-type
Effective pixels—14 MP (4352 x 3264) 
LCD—2.4 in. (6.1 cm) LCD; 112 pixels; 4:3 aspect ratio
Image storage—Optional Class 4 or higher SD/SDHC Card   (or EYE-FI X2 
Card or higher with a firmware version of 4.5174 or higher.) The SD logo is a 
trademark of the SD Card Association. Maximum supported card size: 32 GB
Taking lens—f/4.5; 35 mm equivalent: 35 mm
Lens protection—Built-in
Digital zoom—5X continuous
Shutter...

51www.kodak.com/go/support Appendix
Picture size— 
14 MP (4:3) 4288 x 3216 pixels
12 MP (3:2) 4288 x 2848 pixels
10 MP (16:9) 4288 x 2416 pixels 
6 MP (4:3) 2880 x 2160 pixels 
3 MP (4:3) 2048 x 1536 pixels
Color modes—Vivid, Full, Basic, Black & White, Sepia
Sharpness modes—Sharp, Normal
Video capture—4 GB maximum; VGA (640 x 480 @ 30 fps)
Communication with computer—USB 2.0 high speed -> full speed (PIMA 15740 
protocol); via KODAK Camera USB Cable, Micro B / 5-Pin
Video output—NTSC or PAL...

Appendix
www.kodak.com/go/support
 52
Care and maintenance
■If you suspect water has gotten inside the camera, remove the batteries and card. 
Allow all components to air-dry for at least 24 hours before using the camera.
■Blow gently on the lens or LCD to remove dust and dirt. Wipe gently with a soft, 
lint-free cloth or an untreated lens-cleaning tissue. Do not use cleaning solutions 
unless designed specifically for camera lenses. Do not allow chemicals, such as 
suntan lotion, to contact painted...

53www.kodak.com/go/support Appendix
Upgrading your software and firmware
Download the latest versions of KODAK Software and the camera firmware (the 
software that runs on the camera). Go to www.kodak.com/go/c135downloads.
Storage capacities
The LCD displays the approximate number of pictures (or minutes/seconds of video) 
remaining. For average SD Card capacities, go to www.kodak.com/go/SDcapacities. 
Actual storage capacity varies depending on subject composition, card size, and other 
factors. You may...