Konica Minolta magicolor 2550DN User Manual

							Configuration Menu Overview 37
TRAY 
CHAININGSettingsYES/NO
If YES is selected and the specified paper tray runs 
out of paper during printing, a paper tray loaded with 
paper of the same size is automatically selected so 
printing can continue.
If 
NO is selected and the specified paper tray runs 
out of paper, printing stops.
MAP MODESettingsON/OFF
Select whether or not the Tray Mapping 
function is used.
LOGI-
CAL 
TRAY 
0-9SettingsPHYSICAL TRAY 1/ 
PHYSICAL TRAY 2
Specify whether jobs received from 
another manufacturers printer driver are 
printed using Tray 1 or Tray 2.
PHYSICAL TRAY 2 is the default only 
for 
LOGICAL TRAY 2. The default for 
all other logical trays is 
PHYSICAL 
TRAY 1
.
DUPLEXSettingsOFF/SHORTEDGE/LONGEDGE
If OFF is selected, duplex printing is not possible.
If 
LONGEDGE is selected, the pages will be printed on both sides 
of the paper for long-edge binding.
If 
SHORTEDGE is selected, the pages will be printed on both 
sides of the paper for short-edge binding.
ORIEN-
TATIONSettingsPORTRAIT/LANDSCAPE
Specify the orientation of the media.
PAGE
RECOV-
ERYSettingsON/OFF
Select whether or not the page is printed again after recovering 
from a paper misfeed.
If 
ON is selected, the page that was misfed is printed again.
If 
OFF is selected, printing continues with the next page without 
printing the misfed page.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 38
QUALITY MENU
With this menu, settings for the print quality can be specified.
BLACK
CYAN
MAGENTA
TONER OUT ACTION
REPLACE TONER
AIDCREQUEST AIDC
QUALITY MENU
YELLOW
BLACK
CYAN
MAGENTA
YELLOW
DENSITY CONTROL
MODE
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 39
!All factory default values are shown in bold.
REPLACE 
TONERBLACKSettingsYES
/NO
When YES is selected, the carousel rotates to the 
black toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 82.
CYANSettingsYES
/NO
When YES is selected, the carousel rotates to the 
cyan toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 82.
MAGENTASettingsYES
/NO
When YES is selected, the carousel rotates to the 
magenta toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 82.
YELLOWSettingsYES
/NO
When YES is selected, the carousel rotates to the 
yellow toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 82.
TONER 
OUT 
ACTIONSettingsSTOP
/CONTINUE
When set to CONTINUE, printing continues even if the toner 
cartridge is empty.
When set to 
STOP, printing stops when the toner cartridge is 
empty.
AIDC REQUEST 
AIDCSettingsNO
/YES
If YES is selected, image adjustments are 
performed.
MODESettingsON
/OFF
If ON is selected, the image adjustments are 
applied.
If 
OFF is selected, image adjustments are not 
applied.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 40
DENSITY 
CONTROLBLACKSettings1/2/3
/4/5
Adjust the density of the black toner to one of five 
levels.
If 
1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
CYANSettings1/2/3
/4/5
Adjust the density of the cyan toner to one of five 
levels.
If 
1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
MAGENTASettings1/2/3
/4/5
Adjust the density of the magenta toner to one of 
five levels.
If 
1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
YELLOWSettings1/2/3
/4/5
Adjust the density of the yellow toner to one of five 
levels.
If 
1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 41 INTERFACE MENU
With this menu, interface settings can be specified.
!Restart the printer after changing settings in the ETHERNET menu.
IP ADDRESS
DEFAULT ROUTER
SUBNET MASK
FRAME TYPE
NAME
TCPIPENABLE
DHCP/BOOTP
IPX/SPX
ETHERTALK
ETHERNET SPEED
ETHERNET
INTERFACE MENU
ENABLE HTTP
ENABLE AUTO IP
NETZONE
NETZONE2
NAME2
PS PROTOCOL
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 42
!All factory default values are shown in bold.
ETHER-
NETTCPIP ENABLESettingsYES/NO
If YES is selected, TCP/IP is enabled.
If 
NO is selected, TCP/IP is disabled.
DHCP/
BOOTPSettingsYES/NO
Select whether or not the IP address is 
automatically acquired.
If 
YES is selected, the IP address is auto-
matically acquired.
If 
NO is selected, the IP address is not 
automatically acquired.
IP 
ADDRESSSetting192.168.1.2
Set the IP address for this printer on the 
network.
Use the Up, Down, Left, and Right keys 
to specify the value.
If the IP address is manually specified, 
DHCP/BOOTP is automatically set to NO.
DEFAULT 
ROUTERSetting192.168.1.2
Specify the IP address of the router if one 
is on the network. Use the Up, Down, 
Left, and Right keys to specify the value.
ENABLEUSB
ACTIVE I/F
JOB TIMEOUT
JOB TIMEOUTPARALLEL
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 43
SUBNET 
MASKSetting0.0.0.0
Specify the subnet mask for the network. 
Use the Up, Down, Left, and Right keys 
to specify the value.
ENABLE 
HTTPSettingYES/NO
Specify whether or not HTTP is used.
If 
YES is selected, the Web page pro-
vided to the printer by the built-in HTTP 
server is enabled.
If 
NO is selected, the Web page cannot 
be used.
ENABLE 
AUTO 
IPSettingYES/NO
Select whether or not the IP address is 
automatically acquired when DHCP/
BOOTP and PING, ARP are not 
functioning or when there is no response.
If 
NO is selected, the IP address is not 
automatically acquired.
If 
YES is selected, the IP address is 
automatically acquired.
IPX/SPX FRAME 
TYPESettingsAUTO/802.2/802.3/
ETHER II/SNAP
Specify the protocol used with NetWare.
ETHER
TALKNAME Settingsmagicolor 2550
Specify the name of the printer for finding 
printers with Macintosh EtherTalk.
The printer name can contain a maxi-
mum of 16 characters.
NAME2Settings-
Specify the name of the printer for finding 
printers with Macintosh EtherTalk.
The printer name can contain a maxi-
mum of 16 characters.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 44
NET
ZONESettings✱
Specify the Macintosh EtherTalk zone.
The zone name can contain a maximum 
of 16 characters.
NET
ZONE2Settings-
Specify the Macintosh EtherTalk zone.
The zone name can contain a maximum 
of 16 characters.
ETHERNET 
SPEEDSettingsAUTO/100 FULL DUPLEX/
100 HALF DUPLEX/
10 FULL DUPLEX/
10 HALF DUPLEX
Specify the transmission speed for the network and 
the transmission method for bi-directional 
transmission.
PS 
PROTOCOLSettingsBINARY/QUOTED BINARY
Select whether PostScript jobs are received in the 
binary format or the quoted format.
USB ENABLESettingsYES/NO
If YES is selected, USB is enabled.
If 
NO is selected, USB is disabled.
JOB 
TIMEOUTSettings0-60-999
Specify the length of time (in seconds) until the print 
job being received is timed out when USB is being 
used.
PARAL-
LELJOB 
TIMEOUTSettings0-30-999
Specify the length of time (in seconds) until the print 
job being received is timed out when Parallel is 
being used.
ACTIVE 
I/FSettingsETHERNET/PARALLEL
Specify the interface to be used.
An Ethernet and parallel connection cannot be used at the same 
time.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 45 SYSTEM DEFAULT MENU
With this menu, settings can be specified to adjust the operation of the printer, 
such as the time until the machine enters Energy Saver mode.
PRINT QUALITY
EMULATIONSDEFAULT
AUTO DEFAULT
ERROR PAGE
PCLLINE TERMINATION
FONTPITCH SIZE
FONT NUMBER
POINT SIZE
SYMBOL SET
STARTUP OPTIONSSTART PAGE
DATE & TIME*
ENERGY SAVER
SYSTEM DEFAULT
COLOR MODE
POSTSCRIPT
SYSSTART*
ENERGY SAVER MGT**
SECURITYCONFIGENABLE
SET PASSWORD
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration Menu Overview 46
!* These menu items appear only if an optional hard disk is installed.
** This menu item appears only on 120 V units.
!All factory default values are shown in bold.
PRINT 
QUAL-
ITYSettingsHIGH/STANDARD
Select the image quality for prints.
COLOR 
MODESettingsCOLOR/GRAYSCALE
Specify whether printing is in full color or grayscale.
EMULA-
TIONSDEFAULTSettingsAUTOMATIC/POSTSCRIPT/PCL5/
PCL XL/HEX DUMP/PDF
Specify the printer control language.
If 
AUTO is selected, the printer automatically selects 
the printer control language from the data stream.
AUTO 
DEFAULTSettingsPCL5/POSTSCRIPT
Select the printer description language when it 
cannot be identified from the data and 
DEFAULT is 
set to 
AUTOMATIC.
POST-
SCRIPTERROR 
PAGESettingsON/OFF
Select whether or not an error page is 
printed when a PostScript error occurs.
FORMATFORMAT FLASH
FORMAT DISK*
RESTORE/SAVERESTORE FACTORY
SAVE CUSTOM
RESTORE CUSTOM
CAPTURE PRT JOB*
Downloaded From ManualsPrinter.com Manuals