Kyocera FS 1016MFP User Manual

OPERATION GUIDE10-1
10 Troubleshooting
General Guidelines
The table below provides basic solutions for problems you may encounter with the 
machine. We suggest you consult this table to troubleshoot the problems before 
calling for service.
Symptom Check Item Corrective Action Reference 
Nothing lights on the 
operation panel when 
the power switch is 
turned on.Is the power plug connected to 
an AC outlet?Connect the plug to an AC 
outlet.—
No copies delivered 
after [Start] is 
pressed.Is there some...

Troubleshooting 
10-2OPERATION GUIDE Black or white bands 
on copies.Is the charger wire dirty? Clean the charger wire.page 9-3
Is the charger cleaner in the 
CLEANER HOME POSITION?Remove the process unit and 
return the charger cleaner to 
its home position.page 9-3
If you are using the document 
processor, is the slit glass 
dirty?Clean the slit glass.
It is also possible to use the 
Scan Noise Reduction function 
to make black lines on the 
copies less apparent.page 9-6
Skewed copies. Were the...

Troubleshooting 
OPERATION GUIDE10-3
Maintenance and Error Messages
When any of the following messages appears on the message display, perform the 
procedure provided below.
Message Procedure Reference
Close Scan UnitThe scan unit is open. Close the scan unit. —
Front Cover Open
Close coverThe front cover is open. Close the covers securely. —
Memory Low
Only 1 Copy MadeThe machine’s memory is full. Insert fewer originals and 
try to copy again.—
Open ADF cover
Remove the paperThis appears when the paper...

Troubleshooting 
10-4OPERATION GUIDE
Paper Jam
If a paper jam occurs, copying or printing will stop.
Leave the power switch on and to remove the jammed paper.
WARNING: High voltage is present in the charger section. Take sufficient care 
when working in this area, as there is a danger of electrical shock.
CAUTION: The fuser unit is extremely hot. Take care when working in this area.
Output Tray and Rear Cover
1If paper is not completely ejected into the 
Output Tray, open the Rear Cover and 
remove the...

Troubleshooting 
OPERATION GUIDE10-5
5Close the Scan Unit pushing the Lever.
The error is cleared.
IMPORTANT: Take care not to place your 
fingers between the scan unit and the main 
body when the scan unit is closed. 
Paper Cassette
1Pull out the cassette.
2Remove any partially fed paper.
Check to see if paper is loaded correctly. If 
not, reload the paper.
3Push the cassette back in firmly.
4Open the Scan Unit.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting 
10-6OPERATION GUIDE
5Open the Front Cover.
6Close the Front Cover.
7Close the Scan Unit pushing the Lever.
The error is cleared.
IMPORTANT: Take care not to place your 
fingers between the scan unit and the main 
body when the scan unit is closed. 
Manual Feed Tray
1Remove the paper from the Manual Feed 
Tray.
IMPORTANT: Do not try to remove paper 
that has already been partially fed, proceed 
to step 2.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting 
OPERATION GUIDE10-7
2Open the Scan Unit.
3Open the Front Cover.
4Lift the Developer Unit together with the 
Toner Container out of the printer.
5Using the green handles lift the Drum Unit 
out of the machine.
NOTE: The Drum Unit is sensitive to light. 
Never expose the Drum Unit to light for 
more than five minutes.
6If the jammed paper appears to be pinched 
by rollers, pull it along the normal running 
direction of the paper.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting 
10-8OPERATION GUIDE If it has not be fed as far as the metal 
registration roller, remove the paper from 
the Manual Feed Tray side.
7Return the Drum Unit to its position, aligning 
the guides at both ends with the slots in the 
printer. 
8Insert the Developer Unit together with the 
Toner Container, back into the machine.
9Close the Front Cover.
10Close the Scan Unit pushing the Lever.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting 
OPERATION GUIDE10-9
IMPORTANT: Take care not to place your 
fingers between the scan unit and the main 
body when the scan unit is closed. 
11Reload the Manual Feed Tray.
Inside Machine
1Open the Scan Unit.
2Open the Front Cover.
3Lift the Developer Unit together with the 
Toner Container out of the printer.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting 
10-10OPERATION GUIDE
4Using the green handles lift the Drum Unit 
out of the machine.
NOTE: The Drum Unit is sensitive to light. 
Never expose the Drum Unit to light for 
more than five minutes.
5Remove the paper from the machine.
NOTE: If the jammed paper appears to be 
pinched by rollers, pull it along the normal 
running direction of the paper.
6Return the Drum Unit to its position, aligning 
the guides at both ends with the slots in the 
machine. 
7Insert the Developer Unit together...