Kyocera FS 1120D User Manual

Loading Paper2-13
6Insert the paper cassette into the slot in the printer. Push it straight in 
as far as it will go.
There is a paper gauge on the left side of the front of the paper 
cassette to indicate the remaining paper supply. When paper is 
exhausted, the pointer will go down to the level of (empty).
7Specify the paper size and type for the cassette using Configuration 
Tool. For more information, refer to  Configuration Tool on page3-14.
NoteDo not load paper above the triangle mark located on...

2-14Loading Paper
Loading Paper into MP (Multi-Purpose)Tray
This machine can load up to 50 sheets of 11 × 8 1/2 or A4 paper 
(80 g/m²) into the MP Tray.
1Pull the MP tray towards you until it stops.
2Adjust the position of the paper guides on the MP tray. Standard 
paper sizes are marked on the MP tray. For standard paper sizes, 
slide the paper guides to the corresponding mark.
3Pull out the subtray.
4Align the paper with the paper guides and insert as far as it will go.
IMPORTANTWhen pulling the...

Loading Paper2-15
When loading envelope, place with the envelope flap closed and 
keep the printing side face-up. Insert envelope against the guide 
with the flap on the front or left side until they stop.
5Specify the paper size and type for MP tray using Configuration Tool. 
For more information, refer to Configuration Tool on page3-14.
Paper Stopper
Open the paper stopper shown in the figure.
NoteIf the paper is considerably curled in one direction, for 
example, if the paper is already printed on one...

2-16Loading Paper
Downloaded From ManualsPrinter.com Manuals 

Connecting and Printing3-1
3 Connecting and Printing
This chapter explains how to start up the printer, print from your PC, and 
use the application software included in the CD-ROM.
Connections3-2
Installing the Printer Driver 3-3
Printing 3-9
Status Monitor 3-10
Configuration Tool 3-14
Uninstalling Software (Windows PC) 3-18
Downloaded From ManualsPrinter.com Manuals 

3-2Connecting and Printing
Connections
This section explains how to start up the printer.
Connecting the USB Cable
Follow the steps as below for connecting the USB cable.
1Connect the USB cable (not included) to the USB Interface 
Connector.
2Connect the other end of the USB cable to the computers USB 
interface connector.
Connecting the Power Cord
Install the printer close to an AC wall outlet. If an extension cord is used, the 
total length of the power cord plus ex tension should be 5 meters (16 feet)...

Connecting and Printing3-3
Installing the Printer Driver
Ensure the printer is plugged in and connected to the PC before installing the 
printer driver from the CD-ROM.
Installing the Software in Windows
If you are connecting this printer to a Windows PC, follow the next steps to 
install the printer driver. The example shows you how to connect your printer 
to a Windows Vista PC.
You can use either Express Mode or Custom Mode to install the software. 
Express Mode automatically detects connected...

3-4Connecting and Printing
Express Mode
In Express Mode, the installer automatically detects the printer when 
it is turned on. Use Express Mode for standard connection methods.
1In the installation method selection window, select Express Mode. 
The print system detection window appears and the installer detects 
the connected printers. If the installer does not detect a print system, 
check that the print system is connected via USB or a network and 
that it is turned on. Then click  Refresh to search...

Connecting and Printing3-5
Custom Mode
Use Custom Mode if you want to specify the printer port and select 
the software to be installed.
For example, if you do not want fonts installed on your computer to 
be replaced, select Custom Mode  and deselect the Fonts  checkbox 
in the utility tab.
1Select Custom Mode .
2Following the instructions in the install wizard window, select the 
software packages to be installed and the specify the port, etc.
For details, refer to Custom Installation in the printer...

3-6Connecting and Printing
5Double-click Kyocera OS X x.x.
6The printer driver installation program starts up.
7Choose Select Destination, Installation Type  and then install the 
printer driver as directed by the instructions in the installation 
software.
This completes the printer driver installation. Next, specify the print 
settings.
If an IP, AppleTalk or Bonjour connection is used, the settings below 
are required. If a USB connection is used, the printer is automatically 
recognized and...