Kyocera FS 1350DN User Manual

4-6Connecting and Printing
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1If TCP/IP (IPv6) is set to Off, use U or V to select On and press  
[OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears while you are setting RA(Stateless) and 
DHCPv6.
4Press U or V to select On or Off as the setting for 
RA(Stateless) and DHCPv6.
5Press [OK].
6Press [MENU]. The display returns to...

Connecting and Printing4-7
3Press Z. Each time you press U or V, the selection changes. Refer 
to the explanations below when specifying the settings.
If you are using NetWare, AppleTalk, IPP, SSL Server or 
IPSec to connect to a network, you must enter an administrator ID 
and press [OK]. By default, the administrator ID is the numeric part 
of your printers model name  1350. 
If you are using NetWare, AppleTalk, IPP, SSL Server or 
IPSec to connect to a network, you must enter an administrator...

4-8Connecting and Printing
Set the Security Level to High.
NetWare
This section explains the procedure for enabling NetWare.
1Enter the administrator ID and password. Then, if NetWare is set to 
Off, use U or V to select On and press [OK].
2Press Z.
3Press [OK]. A blinking question mark (?) appears. Each time you 
press U or V, the selection changes.
4Display the item you want to set and press [OK].
5Press [MENU]. The display returns to Ready.
>Security Level
 
High
>NetWare       >
  On
>>Frame Type...

Connecting and Printing4-9
AppleTalk
This section explains the procedure for enabling AppleTalk. 
1Enter the administrator ID and password. Then, if AppleTalk is set 
to Off, use U or V to select On.
2Press [OK]. A blinking question mark (?) appears.
3Press [OK] again.
4Press [MENU]. The display returns to Ready.
IPP
This section explains the procedure for enabling IPP. 
1Enter the administrator ID and password. Then, if IPP is set to Off, 
use U or V to select On.
2Press [OK]. A blinking question mark...

4-10Connecting and Printing
SSL Server
This section explains the procedure for enabling SSL Server.
1Enter the administrator ID and password. Then, if SSL Server is 
set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears.
4Select On or Off using U or V.
5Press [OK].
6Press [MENU]. The display returns to Ready.
IPSec
This section explains the procedure for...

Connecting and Printing4-11
Security Level
Security Level is primarily a menu used by service representative 
for maintenance work. There is no need for customers to use this menu.
>Security Level
  High
Downloaded From ManualsPrinter.com Manuals 

4-12Connecting and Printing
Printing a Network Interface Status Page
You can print out a status page for the network interface. The network 
status page shows the network addresses, and other information under 
various network protocols about the network interface.
Adjust/Maintenance
Adjust/Maintenance is used to adjust the print quality and to carry out 
printer maintenance.
The options available in Adjust/Maintenance are as follows:
•Restart Printer
•Service
1Press [MENU].
2Press U or V repeatedly...

Connecting and Printing4-13
Installing the Printer Driver
According to the instructions of the Installation Guide, connect the PC to 
the printer and turn on them to install the printer driver. 
For more 
information on printer driver, refer to the KX Driver User Guide in the CD-
ROM.
Installing the Printer Driver on Windows PC
This section explains how to install the printer driver in Windows Vista.
1Ensure the printer is plugged in and connected to the computers 
USB or Network port before installing...

4-14Connecting and Printing
•Custom Mode: This option allows you to select items to be installed 
as required and to specify the port.
Proceed the section below according to the installation method.
Express Mode
When selecting Express Mode, printer driver and fonts are installed. 
After installing with this mode, the other utilities can be added using 
Custom Mode.
1On the Installation Method screen, click Express Mode. The 
installer searches the connected printers on Discover Printing 
System screen....

Connecting and Printing4-15
Custom Mode
When selecting Custom Mode, printer port and utilities are changed 
as necessary.
1On Installation Method screen, click Custom Mode.
2On Driver tab and Utility tab of the Custom Installation screen, select 
the printer driver and utilities you want to install, and click Next.
3Select the printer you want to install, and click Next. 
4Confirm the settings and click Install. Printer driver installation 
starts.
5Installation Completed screen appears. Click Finish to...