Kyocera FS C5250DN User Manual

3-11Handling Paper
Thick Paper
Fan the stack of paper and align the edges before loading them in the MP 
tray. Some types of paper have rough edges on the back (those are 
created when the paper is cut). In this case, put the paper on a flat place 
and rub the edges once or twice with, for example, a ruler to smooth them. 
Feeding rough edged paper may cause paper jams.
Note  Use unfolded return postcard (Oufuku Hagaki).
Open the flap.
Landscape
form
envelopes
Close the flap.
Portrait
form
envelopes...

Handling Paper
3-12
Colored Paper
Colored paper should satisfy the same conditions as white bond paper, 
refer to  Paper Specifications on page 3-2 . In addition, the pigments used 
in the paper must be able to withstand the heat of fusing during the 
printing process (up  to 200 °C or 392 °F).
Preprinted Paper
Preprinted paper should satisfy the same conditions as white bond paper, 
refer to Paper Specifications on page 3-2 . The preprinted ink must be able 
to withstand the heat of fusing during the...

3-13Handling Paper
Paper Type
The printer is capable of printing under the optimum setting for the type 
of paper being used.
Setting the paper type for the paper source from the printer’s operation 
panel will cause the printer to automatically select the paper source and 
print in the mode best suited to that type of paper. 
A different paper type setting can be made for each paper source 
including the MP tray. Not only can preset paper types be selected, but it 
is also possible for you to define and...

Handling Paper
3-14
Loading Paper
The following explains the procedure for loading paper in the cassette 
and the MP tray.
Loading Paper into the Cassette
2Pull the paper cassette all the way out of the printer.
3Turn the paper size dial so that the size of the paper you are going to 
use appears in the paper size window.
4While pressing the release lever, slide the left and right paper guides 
to the desired paper size.
Paper Cassette
A4
Paper Size DialPaper Size Window
Note  When the paper size dial is...

3-15Handling Paper
5While pressing the release lever, slide the paper stopper to the 
desired paper size.
Standard paper sizes are marked on the inside of the paper cassette.
6Slide the paper into the paper cassette.
7Insert the paper cassette into the slot in the printer. Push it straight in 
as far as it will go.
There is a paper gauge on the right side of the front of the paper 
cassette to indicate the remaining paper supply. When paper is 
exhausted, the pointer will go down to the level of...

Handling Paper
3-16
Loading Paper into the MP (Multi-Purpose) Tray
2Press the center of the MP tray, and pull it towards you until it stops.
3Pull the subtray toward you until it stops, making sure there are no 
gaps.
4Adjust the position of the paper guides on the MP tray. Standard 
paper sizes are marked on the MP tray. For standard paper sizes, 
slide the guides to the position marked correspondingly.
MP Tray
Subtray
1Fan the media (paper), then tap it on a level surface to avoid 
media jams or skewed...

3-17Handling Paper
5Align the paper with the paper guides and insert as far as it will go.
6Set the MP tray paper size on the printer’s operation panel. Refer to 
MP Tray Size (Setting MP tray paper size) on page 4-29
.
Paper stopper
To use the sheet ejection stopper, open as shown below. (Example: 
Legal)
Load
LimitLoad Limit
Note  Do not load more paper than will fit under the load limits 
on the inside of the MP tray.
When printing on transparencies, feed the sheets into the 
printer one at a time.
If...

Handling Paper
3-18
Downloaded From ManualsPrinter.com Manuals 

4-1
4 Using the Operation Panel
This chapter contains explanations on the following topics:
General Information4-2
Understanding the Operation Panel 4-3
Keys 4-6
Using the Menu Selection System 4-8
Setting a Mode Selection Menu 4-10
Report Print 4-11
USB Memory (USB memory selection) 4-16
Custom Box (Using a Custom Box) 4-18
Job Box 4-22
Counter (Viewing the counter value) 4-28
Paper Settings 4-29
Print Settings 4-37
Network (Network settings) 4-46
Device Common (Selecting/Setting the common device)...

Using the Operation Panel
4-2
General Information
This chapter provides the information you need to configure the Ecosys 
Color printer. In general you need to use the operation panel only to make 
default settings. You can make most changes to the printer settings using 
the printer driver through the application software.
You can also access the printers various settings from a remote location, 
by using the control panel, the printer dr iver or other utilities such as the 
Status Monitor Utility....