Lawn Mower 8211-7060-80 85 Combi, 95 Combi, 105 Combi For Mountfield 2000 And 4000 Series Instruction Manual

8211-7060-80
85 Combi, 95 Combi, 105 Combi
for Mountfield 2000 and 4000 series 

2
125 Combi Pro
4000 series 4WD, 2000 series
ABC(D)
4000 series 4WD
A
B C
4000 series 2WD
GF E
I
H
4000 series 2WD
3
5 
71
4
6 
82 

3
2000 series
17”16”
1/3
11
13
159 
12
14
1610  

4
90°
K K
4000 series 4WD
PP Q
Q
45 Nm
K K2000 series
19
 21
 17
20
22
  18  

5
ENGLISHEN
1 GENERAL
This symbol indicates WARNING. Seri-
ous personal injury and/or damage to 
property may result if the instructions 
are not followed carefully.
You must read these instructions for use 
and the machine’s safety instructions 
carefully.
1.1 SymbolsThe following symbols appear on the machine. 
They are there to remind you of the care and atten-
tion required in use.
This is what the symbols mean:
Warning!
Read the instruction manual and the safety 
manual before using the machine....

6
ENGLISHEN
3 ASSEMBLY
3.1 Assembly on 4WD 4000-series 
and 2000-series
1. Place the deck in position in front of the ma-
chine.
2. Check that the deck mounts are installed on the 
machine as follows.
• Washer (3:D). Only machines up to and in-
cluding 2006.
• Deck mount (3:C).
• Washer (3:B).
• Circlip (3:A).
3. Screw the arms into each other. See fig. 5.
4. Remove the belt cover (6:H) by loosening the 
screws 6:I. 
5. Set the maximum cutting height.
6. Loosen the belt guide screws (21, 22:K) a 
couple...

7
ENGLISHEN
4 USING THE MACHINE
Check that the grass that is to be cut is 
completely free of foreign objects such 
as stones etc.
4.1 Cutting heightThe best cutting results are achieved when the 
when the top third of the grass is cut off. I.e. 2/3 of 
the length of the grass remains. See fig. 14.
If the grass is long and has to be cut significantly, 
cut twice using different cutting heights.
Do not use the lowest cutting heights if the lawn 
surface is uneven. This would entail a risk of the 
blades...

8
ENGLISHEN
4WD 4000-series:
Grip the belt tensioner’s lever with your left 
hand. Pull the lever and unhook with your right 
hand. See fig. 7.
2000-series
:
Unhook the belt idler from the belt. See fig. 9.
7. Loosen the belt guide screws (21, 22:K) a 
couple of turns and work off the belt from the 
cutting deck’s pulley.
8. Force the belt off the deck’s pulley.
9. Grip the front edge of the deck and lift up. Lift 
until the deck is completely vertical and rest the 
rear edge on the ground. See fig. 17....

9
ENGLISHEN
If the blades are not synchronised, one or more of 
the following faults may have occurred in the cut-
ting deck:
• The positive drive belt has slipped on the gear 
wheels.
• Torque limiting between gear wheels and blade 
shaft has deployed. The arrows in fig. 20 must 
be opposite each other for an intact deck. When 
torque limiting has deployed, the arrows are not 
opposite each other.
• The blade member is incorrectly installed on 
the blade shaft. Can be installed in three differ-
ent...

Manufactured by GGP Sweden AB