Lexmark C534dn User Manual

Installing a flash memory or firmware card
The system board has two connections for an optional flash memory or firmware card. Only one of each may be
installed, but the connectors are interchangeable.
CAUTION: If installing a flash memory or firmware card after setting up the printer, turn the printer off, and
unplug the power cord before continuing.
1Access the system board. For more information, see “Accessing the system board to install internal options” on
page 15.
2Unpack the memory card.
Note:...

Notes:
The entire length of the connector on the card must touch and be flush against the system board.
Be careful not to damage the connectors.
5Reinstall the system board access cover.
6Set the printer software to recognize the flash memory.
aClick Start ΠSettings ΠPrinters.
bDouble-click the printer icon.
cClick File ΠProperties.
dClick the Install Options tab.
eFrom the Available Options list, select Flash memory.
fClick Add.
gClick OK.
Installing a printer hard disk
Note: A #2 Phillips...

4Attach the ribbon cable to the hard disk.
5Align the screw holes on the mounting plate with the holes in the hard disk.
6Secure the mounting plate to the hard disk with the screws.
7Press the ribbon cable connector into the connector on the system board.
8Flip the hard disk over, and then press the three posts on the mounting plate into the holes on the system board.
The hard disk snaps into place.
2
1
9Reinstall the system board access cover. For more information, see “Reinstalling the system board...

Installing an internal print server or port interface card
Note: A #2 Phillips screwdriver is needed to install an internal print server or port interface card.
Warning: System board electrical components are easily damaged by static electricity. Touch something metal on
the printer before touching any system board electronic components or connectors.
An internal print server allows connection from the printer to the local area network (LAN). An optional port interface
card expands the ways the printer...

Reinstalling the system board access cover
Note: This operation requires a #2 Phillips screwdriver.
1Align and place the eight keyholes on the system board metal plate onto the screws on the system board.
2Slide the metal plate down.
Installing options
25
Downloaded From ManualsPrinter.com Manuals 

3Tighten the screws firmly.
Attaching cables
Connect the printer to the computer using a USB cable or an Ethernet cable.
A USB port requires a USB cable. Be sure to match the USB symbol on the cable with the USB symbol on the printer.
Match the appropriate cable with the connector shown:
12
3
1Ethernet connector
2USB symbol
3USB connector
Installing options
26
Downloaded From ManualsPrinter.com Manuals 

Loading paper and specialty media
This section shows how to load the standard tray (250-sheet letter size tray), the multipurpose feeder, and the
optional 550-sheet tray which is part of the optional 550-sheet drawer. It also includes information about the standard
exit bin.
Loading the standard tray
The printer has two trays to select from: the standard tray (Tray 1), also known as the 250-sheet tray, and the optional
550-sheet tray (Tray 2). Load the paper or specialty media used for the majority of...

1Load lines
2Length indicator
4Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten
the edges on a level surface.
5Load the paper stack with the recommended print side faceup. Load the stack toward the back of the tray as
shown.
When loading preprinted letterhead, place the header toward the front of the tray.
6Squeeze the width guide tabs, and slide the width guide to lightly touch the side of the stack.
Loading paper and specialty media
28...

7Align the tray, and insert it.
8If a different type of paper was loaded than the type previously loaded in the tray, change the Paper Type setting
for the tray from the control panel. For more information, see “Setting the Paper Size and Paper Type” on
page 35.
Loading the optional 550-sheet tray
The optional 550-sheet drawer consists of a 550-sheet tray and a support unit. This tray is loaded in the same way
that the standard tray is loaded. The only differences between the trays are the look of the...

Loading the multipurpose feeder
1Push the multipurpose feeder latch to the right.
2Pull the multipurpose feeder door down.
3Grasp the extension, and then pull it straight out until it is fully extended.
Loading paper and specialty media
30
Downloaded From ManualsPrinter.com Manuals