LG 22m45d-b Manual

www.lg.com
LED LCD MONITOR MODEL
ENGLISH
OWNER’S MANUAL
LED LCD MONITOR
Please read this manual carefully before operating 
your set and retain it for future reference.
19M45D
20M45D
22M45D
23M45D
24M45D
19M45A
20M45A
22M45A 

2
ENGENGLISH
TABLE OF CONTENTS
CONTENTS
3 ASSEMBLING AND PREPAR-
ING
3  Unpacking
4 Parts and buttons
5 Setting up the Monitor set 
5  - Attaching the Stand Base
5  - Detaching the Stand Base 
6  - Mounting on a table
6  - Using the cable holder
8  - Mounting on a wall
9  USING THE MONITOR SET
9  Connecting to a PC
9  - D-SUB connection
9  - DVI-D connection
11 CUSTOMIZING SETTINGS
12  Customizing Settings
12  - Menu Settings
13    - Picture
14   - Color
15   - Display
16   - Others
17 READER Setting
18...

3
ENGENGLISH
ASSEMBLING AND PREPARING
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing\
 accessories, contact the local 
dealer where you purchased your product. The illustrations in this manual may differ from the actual product 
and accessories.
 yDo not use any unapproved accessories to ensure the safety and product l\
ife span.
 yAny damages or injuries by using unapproved accessories are not covered \
by the warranty. 
 yThe accessories...

4
ENGENGLISH
ASSEMBLING AND PREPARING
Parts and buttons
Power Indicator
 yLighting On: Turned on
 yLighting Off: Turned off
Connection panel (See p.9)
Button (See p.11)
(Power Button)  

5
ENGENGLISH
ASSEMBLING AND PREPARING
Attach the Stand Body to the monitor set.
Attach the Stand Base.
Tighten the screw to the right.
Setting up the Monitor set 
Attaching the Stand Base
1 Place the Monitor set with the screen side 
down on a flat and cushioned surface.
Lay a foam mat or soft protective cloth 
on the surface to protect the screen from 
damage.
CAUTION
2 
Stand Base
Stand Body
1
2
3
Detaching the Stand Base 
1 Place the Monitor set with the screen side 
down on a flat and cushioned...

6
ENGENGLISH
ASSEMBLING AND PREPARING
Mounting on a table
1 Lift and tilt the Monitor set into its upright 
position on a table.
Leave a 10 cm (minimum) space from the wall 
for proper ventilation.
Using the cable holder
2 Connect the AC-DC Adapter and Power Cord 
to a wall outlet.
3 Press (Power) button on the bottom switch 
panel to turn the power on.
10 cm
10 cm
10 cm
10 cm
Unplug the power cord before moving the 
Monitor to another location. Otherwise electric 
shock may occur.
CAUTION
Cable holder...

7
ENGENGLISH
ASSEMBLING AND PREPARING
Using the Kensington security system 
The Kensington security system connector is 
located at the back of the Monitor set. For more 
information of installation and using, refer to the 
manual supplied with the Kensington security 
system or visit http://www.kensington.com.
Connect the Kensington security system cable 
between the Monitor set and a table.
The Kensington security system is optional. 
You can obtain it from most electronics stores.
NOTE
When you adjust...

8
ENGENGLISH
ASSEMBLING AND PREPARING
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm 
on each side and from the wall. Detailed 
instructions are available from your dealer, see the  
optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
If you intend to mount the Monitor set to a wall, 
attach Wall mounting interface (optional parts) to 
the back of the set.
When you install the Monitor set using a wall 
mounting interface (optional parts), attach it 
carefully so it...

9
ENGENGLISH
USING THE MONITOR SET
USING THE MONITOR SET
Connecting to a PC
 yYour Monitor set supports Plug & Play*. 
*Plug & Play:  A PC recognizes a connected 
device that users connect to a PC and turn 
on, without device configuration or user 
intervention.
D-SUB connection
Transmits analog video from your PC to the 
Monitor set. Connect the PC and the Monitor set 
with the supplied D-sub 15 pin signal cable as 
shown in the following illustrations.
 yMac adapter
For Apple Macintosh use, a separate...

10
ENGENGLISH
USING THE MONITOR SET
 yWhen you want to use two PC in our Monitor, 
please connect the signal cable(D-SUB/
DVI-D) respectively in Monitor set.
 yIf you turn the Monitor set on while it is cold, 
the screen may flicker. This  is normal.
 ySome red, green, or blue spots may appear 
on the screen. This is normal.
 y"Self Image Setting" Function.
This function provides the user with optimal 
display settings.When the user connects 
the monitor for the first time, this function...