LG Bh9520tw Owners Manual

							Operating61
Operating4
Using Bluetooth 
technology
About Bluetooth
Bluetooth® is wireless communication technology for short range connection. 
The available range is within 10 meters.
( The sound may be interrupted when the connection interfered by the other electronic wave or  you connect the bluetooth in the other rooms.) Connecting individual devices under  Bluetooth® wireless technology does not incur any charges. A mobile phone with  Bluetooth® wireless technology can be operated via the Cascade if the connection was made via Bluetooth® wireless technology. Available Devices : Mobile phone, MP3, Laptop, PDA
Bluetooth Profiles
In order to use Bluetooth wireless technology, devices must be able to interpret certain profiles.This unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
Listening to music stored on 
the Bluetooth devices
Pairing your unit and Bluetooth 
device
Before you start the pairing procedure, make sure the Bluetooth feature is turned on in to your Bluetooth device. Refer to your Bluetooth device’s user guide. Once a pairing operation is performed, it does not need to be performed again.
1. Select the Bluetooth function by using the FUNCTION. Appears “BT READY” in display window.
2. Operate the Bluetooth device and perform the pairing operation. When searching for this unit with the Bluetooth device, a list of the devices found may appear in the Bluetooth device display depending on the type of Bluetooth device.Your unit appears as “LG Audio”.
3. When this unit successfully paired with your Bluetooth device, Bluetooth LED of this unit lights up and "BTPAIRED" appears in the display window.
Depending on the Bluetooth device type, 
some device have a different pairing way. 
,Note
4.  Listen to music. To play a music stored on your Bluetooth device, refer to your Bluetooth device’s user guide.
If you change the function of the unit, the 
Bluetooth function is disconnected, operate  
pairing again. 
,Note
 
						

							Operating62
Operating4
 
y The sound may be interrupted when 
the connection interfered by the other 
electronic wave.
 
y You cannot control the Bluetooth device 
with this unit.
 
y Pairing is limited one Bluetooth device per 
one unit and multi-pairing is not supported.
 
y Although the distance between your 
Bluetooth and the set is less than 10m, there 
are obstacles between both, your Bluetooth 
device cannot be connected.
 
y Depending on the type of the device, 
you may not be able to use the Bluetooth 
function.
 
y When not connected the Bluetooth, “BT 
READY” appears on the display window.
 
y The Electrical malfunction due to devices 
using same frequency such as Medical 
equipment, Microwaves or wireless 
LAN devices, the connection will be 
disconnected.
 
y When someone stands and interrupts 
communication between Bluetooth device 
and the player, the connection will be 
disconnected.
 
y If the gotten away of the distance between 
Bluetooth and the unit, the sound quality 
is lower and lower the connection will 
disconnect when the space between the 
Bluetooth and the unit gets out of the 
operating range of Bluetooth.
 
y The device with Bluetooth wireless 
technology is disconnected, if you turn off 
the main unit or put the device away from 
the main unit more than 10m. 
,Note
 
						

							5 Troubleshooting
Troubleshooting63
Troubleshooting5
Troubleshooting
General
Symptom Cause & Solution
The Power does not turned on. yPlug the power cord into the wall outlet securely.
The unit does not start playback. yInsert a playable disc. (Check the disc type, color system, and regional code.)
 yInsert the disc with the playback side down.
 yClean the disc.
 yCancel the Rating function or change the rating level.
The angle cannot be changed. yMulti-angles are not recorded on the DVD Video being played.
Cannot play movie, photo or music files. yThe files are not recorded in a format that the unit can play.
 yThe unit does not support the codec of the movie file.
The remote control does not work properly. yThe remote control is not pointed at the remote sensor of the unit.
 yThe remote control is too far from the unit.
 yThere is an obstacle in the path of the remote control and the unit.
 yThe batteries in the remote control are exhausted.
The unit is plugged in, but the power will not turn on or off.You can reset the unit as follows.
 yUnplug the power cord, wait at least five seconds, and then plug it in again.The unit is not operating normally.
 
						

							Troubleshooting64
Troubleshooting5
Network
Symptom Cause & Solution
BD-Live feature does not work. yThe connected USB storage may not have enough space. Connect the USB storage with at least 1GB free space.
 yEnsure that the unit is correctly connected to the local area network and can access the internet (see page 26).
 yYour broadband speed may not fast enough to use the BD-LIVE features. Contact your Internet Service Provider (ISP) and increase the broadband speed is recommended.
 yThe [BD-LIVE connection] option in the [Setup] menu is set to [Prohibited]. Set the option to [Permitted].
Streaming video services (such as YouTube™, etc.) are often stopped or “buffer” during playback.
 yYour broadband service speed may not be fast enough to stream video services. Contact your Internet Service Provider (ISP) and increase the broadband speed is recommended.
Shared folder or files from your PC or a Media servers are not displayed on the device list. 
 yThe firewall or anti-virus software on your media server is running. Turn off the firewall or anti-virus software running on your media server.
 yThe player is not connected to the local area network that your media server is connected.
Cannot connect the player to the access point or wireless LAN router.
 yThe wireless communication may be interrupted from household devices that are using radio frequencies. Move the player away from them.
Access point is not displayed on the “Access point name” list. yThe access point or wireless LAN router may not broadcast its SSID. Set your access point to broadcast its SSID through your computer.
 yYour network device such as access point may not set with available frequency range and channel that this player can support.  Try setting the frequency range and channel on the network device setting.
 
						

							Troubleshooting65
Troubleshooting5
Picture
Symptom Cause & Solution
There is no picture. ySelect the appropriate video input mode on the TV so the picture from the unit appears on the TV screen.
 yConnect the video connection securely.
 yCheck the [HDMI Color Setting] in the [Setup] menu is set to the appropriate item that conforms to your video connection.
 yYour TV may not support the resolution you have set on the player. Change the resolution that your TV accepts.
 yThe player’s HDMI OUT jack is connected to a DVI device that does not support copyright protection.
Picture noise appears yYou are playing a disc recorded in a colour system that is different from your TV.
 ySet the resolution which your TV accepts.
Blu-ray 3D disc playback does not output 3D views. yConnect the player to your TV with HDMI cable ( Type A, High Speed HDMI™ Cable with Ethernet).
 yYour TV may not support “HDMI 3D mandatory format”. 
 yThe [3D Mode] option in the [Setup] menu is set to [Off ].  Set the option to [On].
Sound
Symptom Cause & Solution
There is no sound or the sound is distorted. yThe unit is in scan, slow motion, or pause mode.
 yThe sound volume is low.
 yCheck the speaker cable connection. (page 17)
Customer Support
You can update the Player using the latest software to enhance the products operation and/or add new features. To obtain the latest software for this player (if updates have been made), please visit  http://www.lg.com/global/support or contact LG Electronics customer care centre.
Open source software notice
To obtain the corresponding source code under GPL, LGPL, MPL and other open source licenses, please visit http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are available to download with the source code.
 
						

							6 Appendix 
Appendix66
Appendix6
Controlling  a TV  with 
the Supplied Remote 
Control
You can control your TV using the buttons below.
By pressingYou can
1 ( TV POWER)Turn the TV on or off.
AV/INPUTSwitch the TV’s input source between the TV and other input sources.
PR/CH W/SScan up or down through memorized channels.
VOL +/–Adjust the volume of the TV
Depending on the unit being connected, you 
may not be able to control your TV using some 
of the buttons.
 
,Note
Setting up the remote to 
control  your TV
You can operate your TV with the supplied remote control.  If your TV is listed in the table below, set the appropriate manufacturer code.
1.  While holding down 1 (TV POWER) button, and press the manufacturer code for your TV with the numerical buttons (see the table below). 
ManufacturerCode Number
LG1(Default), 2
Zenith1, 3, 4
GoldStar1, 2
Samsung6, 7
Sony8, 9
Hitachi4
2. Release the 1 (TV POWER) button to complete setting.
Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again.
 
						

							Appendix67
Appendix6
Network Software 
Update
Network update notification
From time to time, performance improvements and/or additional features or services may be made available to units that are connected to a broadband home network. If there is new software available and the unit is connected to a broadband home network, the player will inform you about the update as follows.
Option 1: 
1. The update menu will appear on the screen when you turn off the player.
2. Use A/D to select a desired option and then press ENTER (b).
[OK]Starts the software update.
[Cancel]Exits the update menu and turns the power off.
Option 2:
If the software update is available from the update server, the “Update” icon appears in the Home menu. Press blue (B) colored button to start the update procedure.
Software Update
You can update the player using the latest software to enhance the products operation and/or add new features. You can update the software by connecting the unit directly to the software update server.
 
y Before updating the software in your player, 
remove any disc and USB Device from the 
player.
 
y Before updating the software in your player, 
turn the player off and then turn it back on.
 
y During the software update procedure, 
do not turn off the player or disconnect 
AC power, or do not press any button.
 
y If you cancel the update, turn off the power 
and turn it on for stable performance.
 
y This unit cannot be updated to previous 
software version.
 
,Note
1.  Check the network connection and settings (page 26).page 26).).
2. Select [Software] option in the [Setup] menu then press ENTER (b).
3. Select [Update] option, and press ENTER (b).
The player will check for the newest update. 
 
y Pressing ENTER (
b) while checking for the 
update will end the process.
 
y If there is no update available, the Message, 
“No update is found.” appears. Press ENTER 
(
b ) to return to the [Home Menu]. 
,Note
 
						

							Appendix68
Appendix6
4. If newer version exists, the message “Do you want to download it?” appears. 
5. Select [OK] to start update. (Selecting [Cancel] will end the update.)
6. The player starts downloading the newest update from the server. (Downloading will takes several minutes depending on your home network condition)
7. When downloading is completed, the message, “Download is complete. Do you want to update?” appears.
8. Select [OK] to start updating. (Selecting [Cancel] will end the update and downloaded file will not be re-usable. To update software the next time, the software update procedure has to be started from the beginning again.)
Do not turn off the power during the software 
update. 
>Caution
9.  When update is completed, the power will be turned automatically in a few seconds.
10. Turn the power back on. The system now operates with the new version. 
The Software Update function may not 
work properly depending on your internet 
environment. In this case, you can obtain 
the latest software from the authorized LG 
Electronics Service Centre then update your 
player. Refer to “Customer Support” on page 
65. 
,Note
 
						

							Appendix69
Appendix6
About Nero 
MediaHome 4 
Essentials
Nero MediaHome 4 Essentials is a software for sharing movie, music and photo files stored on your computer to this player as a DLNA-compatiable digital media server.
 
y The Nero MediaHome 4 Essentials CD-
ROM is designed for PCs and should not 
be inserted in this player or in any product 
other than a PC.
 
y The supplied Nero MediaHome 4 Essentials 
CD-ROM is a customized software edition 
only for sharing files and folders to this 
player.
 
y The supplied Nero MediaHome 4 Essentials 
software does not support following 
functions: Transcoding, Remote UI, TV 
control, Internet services and Apple iTunes
 
y The supplied Nero MediaHome 4 Essentials 
software can be downloaded at http://www.
lg.com/global/support. Find the download 
link on the web page of this product. 
 
y This manual explains operations with 
the English version of Nero MediaHome 
4 Essentials as examples. Follow the 
explanation referring to the actual 
operations of your language version.
 
,Note
System Requirements
Windows PC
 yWindows® XP (Service Pack 2 or higher), Windows Vista® (no Service Pack required), Windows® 7 (no Service Pack required), Windows® XP Media Center Edition 2005 (Service Pack 2 or higher), Windows Server® 2003
 yWindows Vista® 64-bit edition (application runs in 32-bit mode)
 yWindows® 7 64-bit edition (application runs in 32-bit mode)
 yHard drive space: 200 MB hard drive space for a typical installation of Nero MediaHome stand-alone
 y1.2 GHz Intel® Pentium® III or AMD  Sempron™ 2200+ processors
 yMemory: 256 MB RAM
 yGraphics card with at least 32 MB video memory, minimum resolution of 800 x 600 pixels, and 16-bit color settings
 yWindows® Internet Explorer® 6.0 or higher
 yDirectX® 9.0c revision 30 (August 2006) or higher
 yNetwork environment: 100 Mb Ethernet, WLAN
Macintosh
 yMac OS X 10.5 (Leopard) or 10.6 (Snow Leopard)
 yMacintosh computer with an Intel x86 processor
 yHard drive space: 200 MB hard drive space for a typical installation of Nero MediaHome stand-alone
 yMemory: 256 MB RAM
 
						

							Appendix70
Appendix6
Installing Nero MediaHome 4 
Essentials 
Windows
Start up your computer, and insert the supplied CD-ROM disc into your computer’s CD-ROM drive. An installation wizard will walk you through the quick and uncomplicated installation process. To install Nero MediaHome 4 Essentials, proceed as follows:
1. Close all Microsoft Windows programs and exit any anti-virus software that may be running.
2. Insert the supplied CD-ROM disc into your computer’s CD-ROM drive.
3. Click [Nero MediaHome 4 Essentials].
4. Click [Run] to start installation.
5. Click [Nero MediaHome 4 Essentials]. The installation is prepared and the installation wizard appears. 
6. Click the [Next] button to display the serial number input screen. Click [Next] to go to the next step.
7. If you accept all conditions, click [I accept the License Conditions] check box and click [Next]. Installation is not possible without this agreement.
8. Click [ Typical] and click [Next]. The installation process is started.
9. If you want to take part in the anonymous collection of data, select the check box and click the [Next] button.
10. Click the [Exit] button to complete the installation.
Mac OS X
1. Start up your computer, and insert the supplied CD-ROM disc into your computer’s CD-ROM drive.
2. Browse the CD-ROM drive and open the “MediaHome_4_Essentials_MAC” folder.
3. Double-click the “Nero MediaHome.dmg” image file. The Nero MediaHome window is opened.
4. In the Nero MediaHome window, drag the Nero MediaHome icon either to the Applications folder within the window or to any other desired location.
5. You can now start the application by double-clicking the Nero MediaHome icon in the location you dragged it to.
Sharing files and folders 
On your computer, you must share the folder contained movie, music and/or photo content to play them on this player. 
This parts explains the procedure for selecting the shared folders on your computer.
1. Double-click the “Nero MediaHome 4 Essentials” icon.
2. Click [Network] icon on the left and define your network name in the [Network name] field. The Network name you enter will be recognized by your player.
3. Click [Shares] icon on the left.
4. Click [Local Folders] tab on the [Shares] screen.
5. Click [Add] icon to open the [Browse Folder] window.
6. Select the folder containing the files you want to share. The selected folder is added to the list of shared folders.
7. Click [Start Server] icon to start the server.
 
y If the shared folders or files are not displayed 
on the player, click the folder on the [Local 
Folders] tab and click [Rescan Folder] at the 
[More] button.
 
y Visit www.nero.com for more information 
and software tools
 
,Note