LG Flatron E1910sm Owners Manual

							20
On Screen Display(OSD) Selection and Adjustment 
Main menu Sub menu Description
NORMALSelect this when you want to use the product
in the most general using environment. 
MOVIE
Select this when you are watching a video or
movie.
INTERNETSelect this when you are working on the
document (Word etc.)
Exit: Exit
,     : Move: Select another sub-menu
When F-ENGINE is not NORMAL,CONTRAST can not be selected.
E1910T/E1910S
E2210T/E2210S
E1910T/E1910S
E2210T/E2210S
E1910T/E1910S
E2210T/E2210S
 
						

							21
On Screen Display(OSD) Selection and Adjustment (Only E2210T/E2210S)
Main menu Sub menu Description
Change the input image signal ratio to
original. 
WIDE
ORIGINALSwitch to full screen mode according to
input image signal.  
* This function works only if input
resolution is lower than monitor ratio
(16:10).
Exit: Exit,     : Move: Select another sub-menu
 
						

							22
On Screen Display(OSD) Selection and Adjustment
Main menu Sub menu Description
E1910T/E1910S
E2210T/E2210S
E1910T/E1910S
E2210T/E2210S
When PHOTO EFFECT is not NORMAL,CONTRAST can not be selected and COLOR is grey.When COLOR is selected down, PHOTO EFFECT is back to 
NORMAL and CONTRAST can be selected now.
PHOTO EFFECT and F-ENGINE should not be unnormal at the same time.
NORMAL  The Photo  Effect function is disabled.
GAUSSIAN
BLURThis menu changes the screen to be more 
colorful and smoother. 
 
						

							On Screen Display(OSD) Selection and Adjustment
23
Main menu Sub menu Description
Exit: Exit,     : Move: Select another sub-menu
E1910T/E1910S
E2210T/E2210S
E1910T/E1910S
E2210T/E2210S
SEPIAThis menu changes the screen to be
Sepia tone (brown color). 
MONOCH
-ROMEThis menu changed the screen to be
Gray tone(black-and-white Picture) .
 
						

							24
Troubleshooting
No image appears
Check the following before calling for service.
No image appears
Do you see a OSD LOCKED message on the screen?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power indicator
flickering?
Do you see an OUT OF
RANGE message on
the screen?
Do you see a CHECK
SIGNAL CABLE
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
Specifications section of this manual and
configure your display again.
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENUbutton for several
seconds: the message 
“OSD UNLOCKED”will appear. Do you see “OSD
LOCKED” when you
push MENU button?
 
						

							25
Troubleshooting
Display image is incorrect
Display Position is
incorrect.
On the screen
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.• Press the AUTObutton to automatically adjust
your display image to the ideal setting. 
If the results are unsatisfactory, adjust the image
position using the H position and V positionicon
in the on screen display.
• Press the AUTObutton to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCKicon in
the on screen display.
• Press the AUTObutton to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, decrease the 
horizontal bars using the PHASEicon in the on 
screen display.
• Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
IMPORTANT
Check Control Panel --> Display --> Settingsand see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
If the recommended resolution (optimal resolution) is not selected, letters may be
blurred and the screen may be dimmed, truncated or biased. Make sure to select
the recommend resolution. 
The setting method can differ by computer and O/S (Operation System), 
and resolution mentioned above may not be supported by the video card    
performance. In this case, please ask to the computer or the video card  
manufacturer. 
 
						

							26
Display image is incorrect
Troubleshooting
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Do you see an Unrecognized monitor, Plug&Play (VESA
DDC) monitor found message?
Have you installed the
display driver?• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lg.com.
• Make sure to check if the video card supports
Plug&Play function.
 
						

							27
48.2 cm (19 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 48.2cm
0.294 x 0.294 mm (Pixel pitch)
Display
Horizontal Freq. 30 kHz to 83 kHz (Automatic)
Vertical Freq. 56 Hz to 75 Hz (Automatic)
Input Form Separate Sync.
DigitalSync Input
Signal Input 15 pin D-Sub Connector
DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo Input
Max VESA 1280 x 1024 @75 Hz
Recommend VESA 1280 x 1024 @60 HzResolution
Plug&Play
On Mode:25 W(Typ.)Sleep Mode≤0.2 W
Off Mode≤0.15 WPower
Consumption
Operating Conditions
Temperature 10 ˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20 ˚C to 60 ˚C
Humidity 5 % to 90 % non-CondensingEnvironment
al Conditions
With Stand
Width    40.89 cm ( 16.10 inch) 
Height 42.95 cm ( 16.91 inch)     
Depth 25.00 cm (   9.84 inch)
Weight(excl. packing) 2.8 kg (6.26 lb)Dimensions
& Weight
Tilt : -5˚ to 15˚Range
AC 100-240 V~ 50 / 60 Hz 0.8 A Power Input
Attached (     ), Detached ( O )Stand Base 
Wall-outlet typePower cord 
DDC 2B(Digital),DDC2AB(Anlaog)
Without Stand
Width    40.89 cm ( 16.10 inch) 
Height 33.81 cm ( 13.31 inch)   
Depth 5.82 cm (   2.29 inch)
NOTE
Information in this document is subject to change without notice.
Specifications                                                                    E1910T
 
						

							28
48.2 cm (19 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 48.2cm
0.294 x 0.294 mm (Pixel pitch)
Display
Horizontal Freq. 30 kHz to 83 kHz (Automatic)
Vertical Freq. 56 Hz to 75 Hz (Automatic)
Input Form Separate Sync.Sync Input
Signal Input 15 pin D-Sub Connector
Input Form RGB Analog (0.7 Vp-p/ 75 ohm)Video Input
Max VESA 1280 x 1024 @75 Hz
Recommend VESA 1280 x 1024 @60 HzResolution
Plug&Play
On Mode:25 W(Typ.)Sleep Mode≤0.2 W
Off Mode≤0.15 WPower
Consumption
Operating Conditions
Temperature 10 ˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20 ˚C to 60 ˚C
Humidity 5 % to 90 % non-CondensingEnvironment
al Conditions
With Stand
Width    40.89 cm (16.10 inch) 
Height 42.95 cm (16.91 inch)     
Depth 25.00 cm (  9.84 inch)
Weight(excl. packing) 2.8 kg (6.26 lb)Dimensions
& Weight
Tilt : -5˚ to 15˚Range
AC 100-240 V~ 50 / 60 Hz 0.8 A Power Input
Attached (     ), Detached ( O )Stand Base 
Wall-outlet typePower cord 
DDC 2AB
Without Stand
Width    40.89 cm (16.10 inch)  
Height 33.81 cm (13.31 inch)   
Depth 5.82 cm (   2.29 inch)
NOTE
Information in this document is subject to change without notice.
Specifications                                                                    E1910S
 
						

							29
55.8 cm (22 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 55.8cm
0.282 x 0.282 mm (Pixel pitch)
Display
Horizontal Freq. 30 kHz to 83 kHz (Automatic)
Vertical Freq. 56 Hz to 75 Hz (Automatic)
Input Form Separate Sync.
DigitalSync Input
Signal Input 15 pin D-Sub Connector
DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo Input
Max VESA 1680 x 1050 @60 Hz
Recommend VESA 1680 x 1050 @60 HzResolution
Plug&Play
On Mode:28 W(Typ.)Sleep Mode≤0.2 W
Off Mode≤0.15 WPower
Consumption
Operating Conditions
Temperature 10 ˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20 ˚C to 60 ˚C
Humidity 5 % to 90 % non-CondensingEnvironment
al Conditions
With Stand
Width    50.64 cm ( 19.94 inch) 
Height 42.49 cm ( 16.73 inch)     
Depth 20.99 cm (   8.26 inch)
Weight(excl. packing) 3.5 kg (7.87 lb)Dimensions
& Weight
Tilt : -5˚ to 15˚Range
AC 100-240 V~ 50 / 60 Hz 1.0 A Power Input
Attached (     ), Detached ( O )Stand Base 
Wall-outlet typePower cord 
DDC 2B(Digital),DDC2AB(Anlaog)
Without Stand
Width    50.64 cm ( 19.94 inch) 
Height 33.32 cm ( 13.12 inch)   
Depth 6.04 cm (   2.38 inch)
NOTE
Information in this document is subject to change without notice.
Specifications                                                          E2210T