LG L1942pk Users Guide

							A20
Troubleshooting
Display image is incorrect
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Do you see an Unrecognized monitor, Plug&Play (VESA
DDC) monitor found message?
Have you installed the
display driver?• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
 
						

							A21
Specifications L1742PK
NOTEInformation in this document is subject to change without notice.
Display 
Sync Input 
Video Input 
Resolution 
Plug&Play 
Power 
Consumption 
Dimensions&Weight
Tilt Range 
Power Input 
Environmental 
Conditions 
Stand Base 
Signal cable 
Power cord 17 inches (43.2 cm) Flat Panel Active matrix-TFT LCD 
Anti-Glare coating 
Visible diagonal size: 
43.2cm
0.264 mm pixel pitch
Horizontal Freq.      Analog : 30 - 83 kHz (Automatic) Digital : 30 - 71 kHz (Automatic)
Vertical Freq. 56 - 75 Hz (Automatic)
Input Form Separate TTL, Positive/Negative SOG (Sync On Green) 
Digital
Signal Input 15 pin D-Sub Connector DVI - D connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital 
Max Analog : VESA 1280 x 1024 @75 Hz Digital : VESA 1280 x 1024 @60 Hz
Recommend VESA 1280 x 1024 @60 Hz 
DDC 2B (Digital), DDC 2AB (Analog) 
On Mode   :
      22  W(Typ.)
Sleep Mode  ≤    1 W
Off Mode   ≤    1 W
With Stand Without Stand
Width 36.96 cm / 14.55 inches 36.96 cm / 14.55 inches 
Height 40.83 cm / 16.07 inches 31.51 cm / 12.41 inches 51.83 cm / 20.41 inches
Depth 24.16 cm / 9.51 inches 5.60 cm / 2.20 inches 
Net 4.07 kg (9.04 lbs) 
Tilt -6˚~17˚ 
AC 100-240V~ 50/60Hz 0.8A  
Operating Conditions Temperature 10˚C to 35 ˚C 
Humidity 10 % to 80 % non-Condensing
Storage Conditions Temperature -20˚C to 60 ˚C
Humidity 5 % to 90 % non-Condensing
Attached(     ), Detached ( O ) 
Attached(     ), Detached ( O ) 
Wall-outlet type or PC-outlet type
 
						

							A22
Specifications L1942PK
NOTEInformation in this document is subject to change without notice.
Display 
Sync Input 
Video Input 
Resolution 
Plug&Play 
Power 
Consumption 
Dimensions&Weight
Tilt Range 
Power Input 
Environmental 
Conditions 
Stand Base 
Signal cable 
Power cord 19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD 
Anti-Glare coating 
Visible diagonal size: 
48.2cm
0.294 mm pixel pitch
Horizontal Freq.      Analog : 30 - 83 kHz (Automatic) Digital : 30 - 71 kHz (Automatic)
Vertical Freq. 56 - 75 Hz (Automatic)
Input Form Separate TTL, Positive/Negative SOG (Sync On Green) 
Digital
Signal Input 15 pin D-Sub Connector DVI - D connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital 
Max Analog : VESA 1280 x 1024 @75 Hz Digital : VESA 1280 x 1024 @60 Hz
Recommend VESA 1280 x 1024 @60 Hz 
DDC 2B (Digital), DDC 2AB (Analog) 
On Mode   :
      24  W(Typ.)
Sleep Mode ≤1 W
Off Mode ≤1 W
With Stand Without Stand
Width 40.63 cm / 16.00 inches 40.63 cm / 16.00 inches 
Height 42.27 cm / 16.64 inches 34.45 cm / 13.56 inches 53.27 cm / 20.97 inches
Depth 24.16 cm / 9.51 inches 5.84 cm / 2.30 inches 
Net 4.47 kg (9.93 lbs) 
Tilt -6˚~17˚ 
AC 100-240V~ 50/60Hz 0.8A  
Operating Conditions Temperature 10˚C to 35 ˚C 
Humidity 10 % to 80 % non-Condensing
Storage Conditions Temperature -20˚C to 60 ˚C
Humidity 5 % to 90 % non-Condensing
Attached(     ), Detached ( O ) 
Attached(     ), Detached ( O ) 
Wall-outlet type or PC-outlet type
 
						

							A23
Specifications
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
*12
**13640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 102431.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.97670
70
60
75
60
75
75
60
75
75
65
60
75
Indicator
On Mode
Sleep Mode
Off Modeblue
flicker
Off
LED Color
MODE
Preset Modes (Resolution)
* Recommend Mode
**Only Analog Mode
 
						

							A24
Installing the Wall mount plate
Wall mount plate (Separate purchase)
This is stand-type or will mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount plate is
purchased.
Kensington Security Slot
Connected to a locking 
cable that can be purchased
separately at most 
computer stores
This monitor satisfies the specifications of the Wall mount plate or
the interchange device.
1. Place the monitor with its front facing downward on a soft cloth.
2.Separate the stand after firstly separating 4 screws by using a driver as figure.
3.Install the Wall mount plate.
 
						

							Digitally yours