LG S33a1d Manual

Getting Started11
Getting Started1
Mounting the main 
unit on a wall
You can mount the main unit on a wall.  Prepare screws and bracket.
Unit
Wall bracket
Wall Mount Bracket 
Installation Template 
1.  Match the TV’s BOTTOM EDGE of  Wall Mount Bracket Installation Template  with the bottom of  TV and attach to the position.
TV
2. When you mount it on a wall (concrete), use the wall plugs (Not supplied). You should drill some holes. A guide sheet ( Wall Mount Bracket Installation Template) is supplied to...

Getting Started12
Getting Started1
3. Remove the Wall Mount Bracket Installation Template.
4. Fix it with screws (not supplied) as shown in the illustration below.
5. Hang the main unit onto the bracket as shown below.
 
y Do not install this unit upside down. It can 
damage the parts of this unit or be the 
cause of personal injury.
 
y Do not hang onto the installed unit and 
avoid any impact to the unit.
 
y Secure the unit firmly to the wall so that it 
does not fall off. If the unit falls off, it...

2 Connecting
Connecting13
Connecting2
Speaker Connection
Wireless connection
LED indicator of wireless subwoofer
LED ColorOperation
YellowThe wireless subwoofer is 
receiving the signal of the 
unit.
Yellow (blink)The wireless subwoofer is 
trying to connect.
RedThe Wireless subwoofer is 
in standby mode.
Off (No 
display)
The Wireless subwoofer is 
turned off.
Initial setting of an ID for the 
wireless subwoofer
1. Connect the power cord of the Wireless 
subwoofer to the outlet.
2. Turn on the main unit...

Connecting14
Connecting2
Connecting  to Your TV
HDMI Connection
If you have a HDMI TV or monitor, you can connect it to this unit using a HDMI cable ( Type A, High speed HDMI™ cable with Ethernet). Connect the HDMI jack on the unit to the HDMI jack on a HDMI compatible TV or monitor.
TVHDMI cable
Set the TV’s source to HDMI (refer to TV’s Owner’s manual).
Additional Information for HDMI
 yWhen you connect a HDMI or DVI compatible device, make sure of the followings:
 -Try switching off the HDMI/DVI...

Connecting15
Connecting2
ARC (Audio Return Channel) 
function
The ARC function enables an HDMI capable TV to send the audio stream to HDMI OUT of the unit.
To use this function:  -Your TV must support the HDMI-CEC and ARC function and the HDMI-CEC and ARC must be set to On.  -The setting method of HDMI-CEC and ARC may differ depending on the TV. For details about ARC function, refer to your TV manual.
 -You must use the HDMI cable ( Type A, High Speed HDMI™ cable with Ethernet).
 -You must connect the...

Connecting16
Connecting2
 
y If your TV does not accept the resolution 
you have set on the unit, you can set 
resolution to 480p as follows:
1. Press 
HOME (
) to disappear the HOME 
menu.
2 Press  Z (Stop) for more than 5 seconds.
 
y If you select a resolution manually and then 
connect the HDMI jack to TV and your TV 
does not accept it, the resolution setting is 
set to [Auto].
 
y If you select a resolution that your TV 
does not accept, the warning message 
will appear. After resolution change,...

Connecting17
Connecting2
Connections with 
external device
OPTICAL IN connection
You can enjoy the sound from your component with a digital optical connection through the speakers of this system.
To the digital 
optical output jack 
of your component
Connect the optical output jack of your component into the OPT. IN jack on the unit. And then select the [OPTICAL] option by pressing FUNCTION (P). Or press OPTICAL/TV SOUND to select directly.
You can also use the F (Function) button on the front panel to...

Connecting18
Connecting2Router
Broadband 
service
DLNA certified servers
Wired network setup
If there is a DHCP server on the local area network (LAN) via wired connection, this unit will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the unit’s network setting to be adjusted. Adjust the [NETWORK] setting as follow.
Preparation
Before setting the wired network, you need to 
connect the broadband internet to your home 
network....

Connecting19
Connecting2
2. Use W/S/A/D to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically.
If there is no DHCP server on the network and 
you want to set the IP address manually, select 
[Static] then set [IP Address], [Subnet Mask], 
[Gateway] and [DNS Server] using W/S/
A/D  and numerical buttons. If you make a 
mistake while entering a number, press CLEAR 
to clear the highlighted part. 
,Note
3.  Select [Next] and press ENTER (b)...

Connecting20
Connecting2
Wireless network setup
For the wireless network connection, the unit needs to be set up for network communication. This adjustment can be done from the [Settings] menu. Adjust the [NETWORK] setting as follow. Setting up the access point or the wireless router is required before connecting the unit to the network.
Preparation
Before setting the wireless network, you need 
to: 
-
connect the broadband internet to the 
wireless home network.
 
-
set the access point or wireless...