Linksys Router BEFW11P1 User Manual

Etherfast
®Wireless AP + Cable/DSL Router with PrintServer
AllocatedThis f ield will show the IP Addresses presently allocated to the other clients on
your Network.
When you are ready to save any changes you have made, click the Savebut-
ton. To undo any changes, click the Cancelbutton.
If you have any questions about anything on this screen, click the Helpbutton
to bring up the Help window for this screen.
16
15
Instant Broadband
TMSeries
You can access this screen at any time by clicking the...

18
You can access this screen at any time by clicking the Optionsbutton.Pass
wor
d
Once a password is entered, it is required in order to change the device conf ig-
uration. Passwords are case sensitive and can be up to eight alphanumeric char-
acters in length.
To create or change a password, enter the password in both the New password
and Verify password f ields.
17
Etherfast
®Wireless AP + Cable/DSL Router with PrintServer
Ad
ditional DNS
The f ields for secondary and tertiary DNS IP Addresses are...

20
19
Etherfast
®Wireless AP + Cable/DSL Router with PrintServer
• SSID (Service Set Identifier).All Wireless devices in your Network must
use the same SSID. Make sure that this f ield reflects the correct SSID for your
network.
• Channel No:All Wireless devices in your Network must use the same SSID.
Make sure that this f ield reflects the correct channel for your network. Should
you experience any interference, you may need to experiment with different
channels to establish a better connection.WEP
Data...

22
Etherfast
®Wireless AP + Cable/DSL Router with PrintServer
You can access this screen at any time by clicking the Statusbutton.
The Status screen will display current data on your Wireless Access Point
Router. This screen will change if you do not enable PPPoE.Har
dwar
e
• Firmware Version.Displays the current program code installed on the hard-
ware.
• Hardware ID.This is utilized by Linksys to identify this device.
• NAT (Network Address Translation).This will display your current NAT...

24
23
Etherfast
®Wireless AP + Cable/DSL Router with PrintServer
The Advanced Options screens gives you the opportunity for further cus-
tomization of the Wireless AP + Cable/DSL Router. While the previous screens
allowed you to setup the Wireless AP + Cable/DSL Router to use, the Advanced
Options screens are optional and should not be modif ied without consulting
either your Network Administrator or reading this user guide. Help buttons are
provided on each screen. If you make a mistake, return to one...

You can access this screen at any time by clicking the Advanced button, fol-
lowed by the Access Controlbutton, and then the Groupsbutton.
The Access Control feature allows administrators to restrict Internet access
through the Wireless AP + Cable/DSL Router’s by individual PCs on the net-
work. The feature utilizes Packet Filtering to block or discard data packets.Selected Entry• Group.By default, this pull-down menu will always be set to Everyone,
which means that all the Access Right for all PCs in...

When you are ready to save any changes you have made, click the Savebutton.
To undo any changes before saving, click the Cancelbutton.
If you have any questions about anything on this screen, click the Helpbutton
to bring up the Help window for this screen.
28
To choose another Selected Entry, simply select the Group from the pull-down
menu. Then, click the Get Databutton to bring up the information specif ic to
that Selected Entry, if it does not come up automatically.Access RightsChanging the option in...

• Reserve entry in DHCP Table.Check this if you wish to reserve an IP
Address for this PC. This is useful if you have to provide the IP Address for
other programs or users. If this is left unchecked, the Reserve IP Addressf ield
will not be active.
• Reserved IP Address.When the Reserve entry in DHCP Tablebox is
checked, this f ield will be active. Enter the reserve address here. This must be
within the range used by the DHCP server.
• Security Group.Use this f ield to identify the security group for...

You can access this screen at any time by clicking the Advanced button, fol-
lowed by the Access Controlbutton, and then the Filtersbutton.
The Access Control:Filters screen allows you to def ine packet f ilters for use on
the Access Control:Groups screen. When you def ine security groups on the
Access Control:Groups screen, you can select from any f ilters def ined here,
along with those pre-set f ilters.TCP P
ack
ets
• Name.Enter a name describing this f ilter.
• Port No.Enter an integer representing...

You can access this screen at any time by clicking the Advanced button and
then clicking the Virtual Serversbutton.
The Virtual Servers screen allows you to create virtual servers within your
Network. In this way, you can make various resources accessible via your web
browser and other applications.
The Virtual Servers feature allows access to Servers on your network from the
Internet. Without this feature, such access would be blocked by the Firewall.
All of your Virtual Servers have the IP Address...