Loewe Individual 46 Compose 3d Operating Instructions

21 -
english
 Connecting the TV set to the Home network
You can connect your TV set to the home network by a wire connection 
(Ethernet, Powerline) or if available by a wireless radio connection (WLAN). 
Please contact your specialist dealer for more information on Powerline.
For the network adapter configuration, see page 65.
➠  Under no circumstances may the TV set be wired and at the same time 
connected by a wireless connection to the same network, e.g. router. 
This may cause severe operational...

- 22
english
Preparing the  remote control unit
Inserting or replacing  batteries
Press on the embossed arrow whilst pushing the battery cover down.
Only use leak-proof micro-cells of the LR 03 (AAA) Alkali-Manganese type. 
Do not use different types of batteries and old and new batteries together.
Pay attention to the correct polarity of + and – when inserting the bat-
teries.
If the batteries are too weak after longer use, the TV set prompts you 
to change the batteries.
Dispose of used batteries in an...

23 -
english
   
Turning the set on/off 
Switching the TV set to  standby mode
Press the  mains switch on the bottom of the set.
The display in the control panel on the front lights up first orange and 
then red. The set is now in standby mode.
Individual 55 / 46 / 40
Individual 32Switching the TV on/off on the control unit
To switch the TV set into Operating mode or switch it off into Standby 
mode, press the middle of the On/Off button for about 2 seconds.
Meaning of the display colour of the LEDs in...

- 24
english
Eco standard:
The emphasis for home use is on low energy consump-
tion. The automatic dimmer is activated.
Premium mode:
This mode optimises the settings to a brighter environ-
ment at a higher energy consumption. The automatic 
dimmer is activated.
Shop mode:
The picture settings are aligned to operation in the presen-
tation room. The automatic dimmer is deactivated. If the 
ambient brightness diminishes, the energy consumption 
is not reduced.
The presetting can be changed later in the TV...

25 -
english
The selection options for the aerials depend on the 
receiver units installed or upgraded at the factory (see 
also page 142). 
Depending on which antenna(s) was (were) selected, the 
appropriate settings are called later during the routine. 
 OK proceed.
  Select desired languages and alternative 
languages for subtitles and audio for DVB 
programmes (see page 59).
       Set up  audio commentary for the visually 
impaired (see page 43).
 OK Proceed.
 Accept Logical Channel Number...

- 26
english
 Setting options for DVB-C reception:
If you have not selected a DVB-C antenna in the antenna 
selection: Continue with Setting options for DVB-S recep-
tion (see right hand column).
The normal DVB-C settings are derived from the selection 
of the location and do not need to be changed.
  Select and adapt settings for DVB-C reception.
  You can state whether coded stations are to be searched 
for in the search/update. 
Select yes to save all found 
scrambled stations. However, these...

27 -
english
 Setting options for the satellite system (2 satellites on 22 kHz switchbox 
/ 2 satellites on toneburst switch):
 Select Satellite 1 / Satellite 2,
  select satellites from list,
 OK Proceed.

 Set LNB frequencies.
    
Normally, you do not need to change the values for 
high and low band, unless the  LNC (LNB) of your 
satellite system uses a different oscillator frequency 
(important for the frequency display).
 OK Proceed.
   (with Setting options for DVB-S reception...

- 28
englishDiSEqC one 
cable 
communal 
system
Satellite
selection
LNB 
frequencies
Manual
registration
(for socket
 ANT SAT)
Transmission channel /frequency
PIN protection
 Setting options for the satellite system  
(max. 4 satellites on DiSEqC multiswitch):
   Select and adapt settings for the DiSEqC multi-
switch.
The refresh rate determines how often a DiSEqC 
command is output. A refresh is only necessary with 
cascaded systems.
The control voltage controls the switching of the 
polarisation...

29 -
english
 Setting options for the satellite system 
(other communal installation):
 Select  satellite,
 OK Proceed.
   Select and adapt settings.
   
Normally, you do not need to change the values for high 
and low band, unless the  LNC (LNB) of your satellite 
system uses a different oscillator frequency (important 
for the frequency display).
If your set is connected to a single-cable system without 
external voltage supply, you can connect the antenna 
supply (13V or 18V / max. 450mA).
 OK...

- 30
english
 Setting options for all types of reception:
 Select favoured signal source.
   Select the signal source from a list, the station of 
which is to be at the top of your station list (starting 
with station slot 1).
   The listed signal sources depend on the selected 
antennas and, if the set is equipped with a satellite 
tuner, the type of satellite system used and the 
received satellites.
 OK Proceed.
You will see a list of the selected settings. You can go 
back in steps with the ...