Loewe Individual 46 Compose Full Hd Operating Instructions

							
41	-

Connecting other speaker systems or active 
speakers to the Dolby Digital Decoder
If	you	 want	 to	use	 another	 similar	speaker	 system	or	 active	 speakers,	
you	 can	connect	 these	to	the	AUDIO LINK 	interface	 of	the	 TV	set	 with	
an	adapter	cable.
The 	adapter 	cable 	is 	available 	from 	your 	dealer 	(see 	Accessories, 	page 	55).
Connecting
Before 	connecting 	any 	devices 	ensure 	that 	they 	are 	switched 	off 	or	
unplug	their	mains	plug.
Plug	 the	adapter	 cable	into	the	
AUDIO LINK  interface	of	the	 TV	set.	 Con-
nect	 the	cinch	 connections	 of	the	 adapter	 cable	to	the	 connections	 of	
the	corresponding	active	speakers.	
The	cinch	connections	of	the	adapter	cable	are	labelled:
R 			 	 for	front	rightL		 	 	 for	front	leftC 			 	 for	centreSR 		 	 for	surround	rightSL		 	 for	surround	leftSUB 			 for	subwoofer
The connections on the adapter cable are preamplifier outputs. Therefore, only active speakers may be connected directly to the adapter cable.
Operating additional equipment
Adjusting the speaker system
Calling the sound components wizard
➠ In	normal	TV	mode,	without	other	displays.
Call	
TV menu.
	34 	Select	Connections,		6	go	to	the	menu	line	below.
	34 	Select	Sound components,		OK  calls	the 	sound	components	wizard.
Sound playback via ... speakers system
Enter	here	that	you	want	 to	hear	 the	TV	sound	 over	a	speaker	 system.
	
If	you	connect	active	speakers,	please	use	the	setting	
Speakers system.
	 6 	Mark	
Speakers system,
	OK  to	continue.
If	nothing	has	been	set	yet	then	the	factory	values	will	
be	displayed,	otherwise	the	values	last	set	will	be	
displayed.
continued	on	the	next	page	Ž
END
OK
OKTV speakersSpeakers system                                  HiFi/AV amplifierHiFi/AV amplifier or TV speaker (switchable)
Sound componentsSound playback via ...
Sound components wizardPlease specify here via which sound components you want to listen to you\
r TV sound. If you select a Speaker system, this must be connected to th\
e AUDIO LINK socket on the back of the TV set (with an additional adapter\
 if necessary).If your TV has no built-in speakers, the sections relating to TV speakers“ may not be selected.
Proceed
ENDOK
OK
Proceed
Configuration/modificationSpeakers systemSound components
Sound components wizardPlease specify whether you want to change the illustrated setting of you\
r speakers system or whether all existing settings are to be reset to the \
values of the delivery state.      Components             Distances                Level
4,0m4,0m0dB0dB
Reset to factory settings
TVTVTVTVTVTV
RSRSLLCSUB
RSRSLCSUBL
Adapter	cable TV	set
FrontRightFrontLeft
SurroundLeftSurroundRight
Centre
Subwoofer
Connection	of	active	speakers	to	the	TV	set
Downloaded	From	TV-Manual.com	Manuals 
						

							
-	4

Operating additional equipment
If	you	want	to	set	new	sound	components	or	change	them:
	34	Select	Configuration/modification,		OK   calls	the	selection,	whether	complete,	partial	or	
new	set-up.
	 6 	Select	
Complete,		OK  continue	to	connect	and	set	the	front speakers.
34 	Select	External speakers,	
	 6	 go	to	the	menu	line	below	and
34	 	set	the	
lower limit frequency 	of	the	front	speakers	
in	10	Hz	steps.
➠  Select	 the	start	 value	 of	the	 frequency	 response	of	the	
speakers	 for	the	 right	 setting	 (e.g.	50Hz	 for	the	 specifica
-
tion 	"Frequency 	response 	50- 0.000Hz"). 	See 	the 	techni-
cal	data	of	the	speakers	for	the	value.
➠  You	 can	replace	 the	external	 front	speakers 	by	 the	 TV	speakers 	if 	necessary. 	In 	this 	case, 	select 	TV speakers .	Then	
transmit	the	sound	of	the	 front	speakers.
	OK   continue	to	connect	and	set	the		surround speakers.
34 Select	yes 	for	 external	speakers.
➠ If	no	 surround	 speakers	are	 connected,	 these	can	be	
simulated	using	the	 front	and	centre	speakers.
	6	 Go	to	the	menu	line	below	and
34	 	set	the	lower limit frequency 	of	the	surround	
speakers	 in	10	Hz	steps.
➠ Select	 the	start	 value	 of	the	 frequency	 response	of	the	
speakers	for	the	right	setting.
  OK  continue	to	connect	and	set	the	
centre speaker.
34  Select	whether	the	TV speakers  or	an	External speaker	is	to	reproduce	the	centre	sound	or	no	if	
no	 centre	speaker	is	connected.
➠ If	no	 centre	 speaker 	is	 connected,	 the	front	 speakers	
also	transmit	the	centre	sound	parts	additionally.
	 6	 	for	
External speakers 	go	to	the	menu	line	below	and
34	 	set	the	lower limit frequency 	of	the	centre	speaker	
in	10	Hz	steps.
➠  Select	 the	start	 value	 of	the	 frequency	 response	of	the	
speakers	for	the	right	setting.	
  OK  continue	to	connect	the	
Subwoofer.
34  yes 	is	the	selection	for	subwoofer.
➠ If	no	 subwoofe r	is	 connected,	 the	front	 speakers	 also	
transmit	 the	sound	 parts	intended	 for	the	subwoofer 	as	
far	as	possible	additionally.
continued	on	the	next	page
Ž
END
OK
OK
Proceed
Complete
Distances onlyConnections only
Configuration/modification of speaker systemSound components
Sound components wizardPlease specify here whether you want to completely reconfigure a speaker\
s system or whether you want to limit the configuration to changing the speaker connections, the speaker distances from the listening position o\
r the individual speaker levels in relation to each other.
Levels only
ENDOK
External speakersConnect front speakersSound components
Sound components wizardPlease specify here whether you want to connect external front speakers. In this case, their lower limit frequency must be entered in Hz (see instruction manual and technical data of the speakers).
 40 HzProceed
TV speakersTV speakers
40Hz40Hz
ENDOK
70Hz70Hz
External speakers 70 Hz
Connect front speakersSound components
Sound components wizardPlease specify here whether you want to connect external front speakers. In this case, their lower limit frequency must be entered in Hz (see instruction manual and technical data of the speakers).
Proceed
 
						

							
4	-

Operating additional equipment
 OK   continue	to	set	the	Distance from the left front speaker.
➠  Measure	 the	distances	 from	your	sitting	 position	 to	
the 	front, 	surround, 	and 	centre 	speakers 	respectively. 	The	
Dolby	 Digital	 Decoder	 calculates	 the	delay	 times	 for	the	
speaker	 signals	from	these	 so	that	 they	 reach	 the	listen
-
er	simultaneously.
34	 	Set	the	distance	between	the	left	 front	speaker	
and 	your 	listening 	position 	in 	10 	cm 	steps.
  OK  continue	respectively	to	the	other	speakers	and	
34 	adjust	the	distance.
➠ After	setting	the	distance	for	the	 centre	speaker	...
  OK  continue	to	
Adjust speaker level.
34 	Adjust	the	volume	for	each	speaker.
6 	Select	speakers	manually.
➠ For	 balanced	 audio	reproduction	 all	speakers	 should	
be	 set	 at	the	 same	 volume	 level.	A	noise	 signal	 will	be	
reproduced 	automatically 	on 	each 	speaker 	in 	succession.	
From 	your 	sitting 	position 	adjust 	each 	speaker 	to 	the 	same	
volume.  
OK  continue	to	
Subwoofer phase.
Switch 	to 	a 	station 	with 	music 	with 	
P+/P– 	or 	start 	playback	
with	music	on	a	DVD	player.
34	 	Test	both	values	(0º	and	180º)	and	select	the	one	
for	which	the	bass	reproduction	is	clearer.
	OK	 to	confirm	the	setting	and	exit	the	wizard.
This	ends	the	 sound	components	wizard 	for	connect
-
ing	and	setting	up	a	speakers	system.
END
OKProceed
Distance to left front speaker 4,2 m
Sound components
Sound components wizardPlease enter the distance of the left front speaker from your listening position here.4,2m4,0m
1,0m0,9m
2,7m
0dB0dB
0dB0dB
END
OK
Adjust speaker level 0 dB
Sound components
Sound components wizardYou hear a sound from every speaker one after another. But you can also select the speakers manually with the menu control buttons up/down. Set the volume for the respectively active speaker shown in blue so that you get approximately the same volume impression from all the speakers.
Proceed                           Preceding/next loudspeaker
ENDOK0°Subwoofer phaseSound components
Sound components wizardHere you can reverse the phase of your subwoofer. Test both values in mu\
sic reproduction and then select the one with which you get a better bass reproduction.
180°Proceed
 
						

							
-	44

Connecting audio amplifiers
The	sound	 components	 wizard	permits	 configuration	 of	different	 audio	
amplifiers 	(stereo 	amplifiers, 	surround 	amplifiers, 	analogue 	or 	digital) 	with	
different 	digital 	audio 	formats 	(Dolby 	Digital, 	dts, 	MPEG, 	and 	stereo/PCM).	
See	the	operating	manual	of	the	audio	amplifier	for	more	information.
Call	
TV menu.
 34	Select	Connections,		6	 go	to	the	menu	line	below.
	34	 Select	Sound components.
  OK  calls	the	sound	components	wizard
6	 Mark	the	
HiFi/AV amplifier.
  OK  to	continue.
34	 Select	Digital audio transmission.
Continue, 	depending 	on 	the 	amplifier, 	see 	right 	column.
Explanations of the setting possibilities:
Select	setting	 if	an	 amplifier	 is	connected	 and	your	 TV	set	
does	not	have	any	TV	speakers	connected.
Select	 setting	 if	an	 amplifier	 is	connected	 and	your	 TV	set	
has	 TV	speakers	 connected.	 In	the	 sound	 mode	selection	
the	 sound	 reproduction	 can	then	 be	switched	 back	and	
forth	between	the	amplifier	and	the	TV	speakers.
Specify	 sound	formats	 which	can	be	decoded	 with	the	
digital 	amplifier 	(see 	operating 	manual 	of 	the 	used 	ampli
-fier).
Select	either	stereo	or	surround	amplifier.
For	 every	 connected	 surround	amplifier,	 select	whether	
the	TV	loudspeakers	are	to	be	used	as	centre	speaker.
If	 so,	 establish	 a	connection	 between	the	centre	 output	
of	 the	 amplifier	 and	the	centre	 input	of	the	 TV	set	
AUDIO IN1 C 	with	a	cinch	cable.
Attention:  Do  not  use  the  centre  speaker  connection  of the amplifier, use the centre pre-amp output instead!
Connecting digital audio amplifiers
Continuation	of	the	left	column	above	...
For	digital	audio	transmission:	Select	
yes.
Connect	 the	digital	 audio	output	 of	the	 TV	set	
AUDIO DIGITAL OUT  with	the	digital	 audio	input	of	the	 amplifier	
via	a	cinch	cable:
Sound	formats,	amplifier	type	and	other	settings,	see	
explanations	of	the	setting	possibilities.
Connecting analogue audio amplifiers
Continuation	of	the	left	column	above	...
For	digital	audio	transmission:	Select	
no.
Connect 	the 	analogue 	audio 	output 	of 	the 	TV 	device	
AUDIO OUT L/R  via	a	stereo	 cinch	cable	to	the	 analogue	
audio	input	of	the	amplifier:
For 	selecting 	the 	amplifier 	type 	and 	making 	other 	settings,	
see	explanations	of	the	setting	possibilities.
Operating additional equipment
HiFi/AV	amplifier
HiFi/AV	
amplifier 	or 	TV	
speakers(switchable)
Sound 	formats
Type 	of	
amplifier
TV 	loudsp. 	as	
centre 	speaker
END
OK
OK
TV speakersSpeakers systemHiFi/AV amplifier                                   HiFi/AV amplifier or TV speakers (switchable)
Sound componentsSound playback via ...
Proceed
PREOUTFRFL
SLSRSUB
CLL
RR
AUX1 INDIGITALINDIGITALOUT
AUX OUTAUX 2
TV	set
Digital	amplifier
AUDIO	DIGITAL	OUT
PREOUTFRFL
SLSRSUB
CLL
RR
AUX1 INDIGITALINDIGITALOUT
AUX OUTAUX 2
AUDIO	OUT	L/R
TV	set
Analog	amplifier
Downloaded	From	TV-Manual.com	Manuals 
						

							
45	-

Assignment of the digital audio input
Your	TV	set	 can	 assign	 an	AV	 input	 to	the	 digital	 audio	input	socket	AU-DIO DIGITAL IN .	When	switching	over	to	this	AV	input,	the	digital	audio	
signal 	at 	the 	AUDIO DIGITAL IN 	input 	is 	passed 	on 		to 	the 	integrated 	Dolby	
Digital	 Decoder	 and	the	digital	 audio	output	 socket	AUDIO DIGITAL OUT .	
You	 will	hear	 the	digital	 sound	 of	the	 assigned	 AV	input,	 if	available,	 in	
place	of	the	analogue	sound.
Connecting devices to the digital audio input
You	 must	 feed	the	digital	 audio	signal	 to	the	 TV	set	 for	sound	 reproduc
-
tion	from	an	external	device,	e.g.	from	the	DVD	player.
Reproduction	 of	the	 external	 digital	audio	signal	 can	be	played	 back	via	
the	 Dolby	 Digital	 Decoder	 integrated	 in	the	 TV	set	 or	via	 an	externally	
connected	digital	audio	amplifier.	
➠  If	an 	external 	audio 	amplifier 	is 	used, 	this 	must 	be 	regis-
tered 	in 	the 	sound 	components 	wizard 	(see 	page 	44).
Call	
TV menu.
 34	 Select	Connections,		6	 go	to	the	menu	line	below.
	34	 Select	Miscellaneous,		6	 go	to	the	menu	line	below.
34	 Select	Assign digital audio input,	
	6	 go	to	the	menu	line	below.
34	 Select	AV input.
To	 connect	 a	DVD	 player	 to	the	 digital	 audio	input	of	the	
TV	 set	 for	example,	 connect	the	digital	 output	 socket	of	
the	 DVD	 player	 (DIGITAL	 OUT)	via	a	cinch	 cable	to	the	
AUDIO DIGITAL IN 	socket	on	the	TV	set.
S-VIDEO OUTDIG OUT
REARMAINSLR(CVBS)(Y/C)VIDEO OUTAUDIO
STEREO OUTVIDEO OUTIAUX-I/O
IITO TV-I/OOPT OUTRIGHTSUBW.REARRIGHTFRONT
LEFTCENTERMULTICHANNEL AUDIO OUTDIGITAL AUDIO OUTPCM/MPEG2/AC3/DTSLEFTFRONT
TV	set
DVD	player AUDIO	DIGITAL	IN
AV1
The	DVD	player	is	already	registered	at	AV1	in	the	
connection	wizard
	at	the	factory.	
If 	new 	devices 	are 	connected 	and 	registered 	in 	the	
connection 	wizard ,	the 	digital 	audio 	input 	
AUDIO DIGITAL IN is	assigned 	in 	the 	connection 	wizard (see 	page 	6).
Audio connection in HDMI (DVI) devices
Devices with DVI connection
If	 an	 external	 device	with	DVI	interface	 is	connected	 via	a	HDMI/DVI	
adapter	 to	the	
HDMI1/DVI 	or	HDMI2/DVI 	socket	 of	the	 TV	set,	 you	 can	
connect 	the 	digital 	sound 	of 	the 	external 	device 	to 	the 	digital 	audio 	input	
socket	
AUDIO DIGITAL IN .	
The	 assignment	 of	the	 digital	 audio	input	to	the	 corresponding	 HDMI	
socket	of	the	TV	set	takes	place	as	described	in	the	column	on	the	left.
If	 you	 want	 to	use	 the	analogue	 sound	of	the	 external	 devices,	connect	
it	to	the	
AUDIO IN2 	socket.
Devices with HDMI connection
If	external	 devices	with	HDMI	 interface	 are	connected	 to	the	
HDMI1/DVI	
or	HDMI2/DVI 	socket	 of	the	 TV	set,	 no	assignment	 of	the	 audio	 input	is	
necessary	 because	the	digital	 transmission	 of	picture	 and	sound	 takes	
place	via	one	connection	in	HDMI.
Operating additional equipment
to AV2to AV1Assign digital audio input
TV menuConnectionsMiscellaneous
to AVSto HDMI1/DVIto HDMI1/DVIno
ENDINFO
 
						

							
-	46

Operating additional equipment
The direct way to record
You	can	programme	 timer	recordings	 via	the	 integrated	 Digital	Recorder	
or	 connected	 recorders	on	the	 TV	set.	 The	 recording	 wizard	is	 integrated	
at 	several 	places 	for 	programming 	a 	recording. 	Further 	information	
about	 recording	 with	the	Digital	 Recorder	 can	be	found	 in	a	separate	
operating	manual.
Programming a timer recording with the EPG
➠ 	You	are	in	EPG	mode,if	not,	press	the	EPG button.
	6 	Mark	the	desired	programme.
Red button: Call	Timer data.
Change	or	confirm	
Timer data 	as	necessary.
Programming a timer recording via teletext
➠ You 	are 	in 	Teletext 	mode; 	if 	not, 	press 	the 	TEXT button.
Call	the	programme	pages	of	the	current	station.	
	
Change	preset	page	numbers,	see	this	page	1.
Green button:  Go	to	the	appropriate	page.
	6	 Select	desired	broadcast,
		OK	calls Timer data.
Change	or	confirm	
Timer data  as	necessary.
Enter timer data
Timer	data	are	displayed	 after	selecting	 the	programme	
you 	want 	to 	record. 	You 	can 	change 	these 	before	
confirming.
  OK   confirms	
Timer data,	
or	change	if	necessary:
	34	 Select	Recorder.
	6
	Select Date.
	 	 Enter 	the 	recording 	date 	with 	the 	numeric buttons.
	6	
Select Recording time.
	 	 Enter 	the 	recording 	time 	with 	the 	numeric buttons.
	6 Select	
VPS.	34	Set yes/no.
	6	 Select	
Recording type.		34	Set	once,	Mon-Fri,  daily, weekly.
	OK	 confirm	the	Timer data.
Setting possibilities in the Timer data menu:
Selection	of	the	connected/integrated	recorder.
Day	of	recording.
Time	of	recording.
Use	VPS	data,	yes/no.
(Some	stations	do	not	broadcast	a	VPS	signal).	
once ,	Mon–Fir,	daily	or	weekly.
Serial	 can	also	 be	selected	 for	timer	 recordings	 with	the	
EPG.
➠ If	you	 use	an	external	 recorder	 without	Digital	Link	Plus,	 you	have	 to	
select	 the	recording	 source	in	the	 recorder	 (e.g.	AUX).	 This	is	the	 case	
when	DVB	programmes	are	to	be	recorded.	The	TV's	receiver	is	used.
➠  If	you	 use	an	external	 recorder	 with	Digital	 Link	Plus	or	a	comparable	
system	according	to	protocol	50,	this	is	controlled	automatically.
ENDINFO
OK
OK
Timer data12.00 Brisant
Switch recorder to AUX!   confirm
Recorder         DVD-RECStation           01 Das ErsteDate             14.09.2006Recording time    17.15 until 17.45VPS              noRecording type    once only
DR
OK3 0 0  < <                                                           A b e n d   >  3 0 3
Select programme                    Record
1 4 . 0 0       T a g e s s c h a u1 4 . 1 0       I n   a l l e r   F r e u n d s c h a f t  U T .   .   .   .   .   .   .   .   .   .   .     3 1 6      Z w e i t e   B e g e g n u n g   ( D ,   2 0 0 5 )1 5 . 0 0      T a g e s s c h a u1 5 . 1 0       S t u r m   d e r   L i e b e   ( 2 2 1 )   .   .   .   .   .   .   .   .   .   .   .   .   .     3 1 71 6 . 0 0         T a g e s s c h a uU T1 6 . 1 0         E i s b ä r ,   A f f e   &   C o .     .   .   .   .   .   .   .   .   .   .   .   .   .   .   .    3 1 81 7 . 0 0       T a g e s s c h a u   u m   f ü n fU T1 7 . 1 5       B r i s a n t     .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .    3 1 91 7 . 4 7       T a g e s s c h a u1 7 . 5 5       V e r b o t e n e   L i e b e     .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .     3 2 01 8 . 2 0       M a r i e n h o f     .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .    3 2 11 8 . 5 0       D a s   G e h e i m n i s   m e i n e s     .   .   .   .   .   .   .   .   .   .   .   .   3 2 2      V a t e r s   ( 1 9 )1 9 . 2 0       D a s   Q u i z   m i t   J ö r g   P i l a w a   .   .   .   .   .   .   .   .   .   .      3 8 4      b i s   1 9 . 5 0   U h r
    3 0 1       3 0 2        A R D t e x t                    D o       1 4 .   0 9 .   0 6                 0 9 :   3 6   :   4 2
–            +J e t z t   i m   T V                                    A R D   m o r g e n
D o       1 4 .   0 9 .   0 6            D a s   E r s t e
ENDMENUP+P–TEXTOK09-
OK15:57-16:59 arte          Charmed - Zauberhafte Hexen16:00-16:15 MDR FERN...    Hier ab vier16:00-16:10 EinsExtra      EinsExtra Aktuell16:00-17:15 SAT.1         Richter Hold16:00-16:30 ProSieben      M. Asam - Mode16:00-16:55 ZDFtheater...   Waschtag16:05-17:00 Bayrische...    Wir in Bayern16:05-16:45 KiKa          Skippy, der Buschpilot16:05-17:00 KABEL1        Star Trek - Das nächste Jah...
2 ZDF
EPG (Electronic Programme Guide)              Mon 31.07./16:05
Detail              View                         RecordPage ↑↓            Select time                 Select date, ... , topics
DateTimeStationTopics
Mon 31.07nowallall
soon17:0018:0019:00
Charmed - Zauberhafte Hexen 
20:00
Recorder
Date
Recording 	time
VPS
Recording 	type
Downloaded	From	TV-Manual.com	Manuals 
						

							
47	-

Operating additional equipment
Programming the timer with the timer overview
A	timer	recording	can	also	be	programmed	manually.
Call	
Timer list.
You	see	a	list	of	all	previously	programmed	timers:
Green button: 		Change	timer	recording.
Yellow button: 		Delete	timer	recording.
Red button: 		New	timer	recording.
Programming the timer manually
	➠  The	timer	overview	is	open.
Red button: 	 Call	the	recording wizard.
	34	Select	Manual,		OK call	Station selection.
346	 Select	station.
  OK
 calls	the Timer data.
For	time	data	input,	see	page	46.
After	 confirming	 the	timer	 data,	the	 new	 recording	 is	
transferred	to	the	 timer	overview
.
Explanation 	of 	the 	setting 	possibilities 	of 	the 	recording 	wizard
:
	 Via	EPG 	 Timer	programming 	via 	EPG 	(see 	Programming 	timer	
recording	via	EPG,	page	46).
	 Via	Teletext 	 Timer	programming	 via	Teletext	 (see	Programming	 timer	
recording	via	Teletext,	page	46).
	Manual 	 Programming	timer	manually	(see	above).
Timer recording with external devices
Recorder with Digital Link Plus
If	 you	 use	an	externally	 connected	 recorder	with	Digital	 Link	Plus	or	a	
similar	 system,	 the	TV	set	 and	 connected	 recorder	exchange	 data	(e.g.	
compare 	station 	lists 	TV 	set/recorder 	or 	timer 	data 	of 	analogue 	sta
-
tions).	
Please	 consult	 the	operating	 manual	of	your	 recorder	 to	find	 out	if	your	
recorder	 is	Digital	 Link	Plus	compatible.	 In	addition	 use	only	 Euro	 AV	
cables	for	the	connection	between	TV	set	and	recorder.
Analogue stations
The	 timer	 data	are	transmitted	 automatically	 from	the	TV	set	 to	
the	 recorder	 after	programming	 is	complete.	 (For	DVD	 recorders	
in	addition	the	recording	quality	SQ	or	EQ	is	also	transmitted.)
The	 recording	 then	is	controlled	 by	the	 recorder	 and	the	recorder	
tuner	is	used	for	reception	of	the	programme.
The	 recording	 data	are	not	 saved	 in	the	 timer	 overview 	of	 the	 TV	
set.	Consequently	 if	you	want	to	change	or	delete	the	timer	data	
then	you	must	do	so	on	the	recorder.
Digital stations
If	 you	 want	 to	record	 digital	stations	 with	an	externally	 connected	
recorder,	 then	the	DVB	 tuner	 is	used	 and	the	TV	device	 takes	over	
control	 of	the	 recorder.	 Then	the	station	 on	the	 TV	set	 is	locked	
during	 the	timer	 recording.	 It	is	 not	 possible	 to	switch	 over	to	
another	DVB	station.	
Recorder without Digital Link Plus
If 	you 	cannot 	programme 	your 	externally 	connected 	Loewe 	recorder 	from	
the	 TV	set,	 but	it	supports	 Digital	Link	(Loewe-own	 system),	the	receiver	
of	the	TV	set	is	always	used.	
Digital	 Link	must	 be	switched	 on	on	the	 recorder.	 Read	the	operating	
instructions	of	your	Loewe	recorder.
In	 addition	 use	only	 Euro	 AV	cables	 for	the	 connection	 between	TV	set	
and	recorder.
Analogue and digital stations
You	 can	control	 the	recording	 from	the	TV	set.	 The	 recorder	 must	
be 	set 	manually 	to 	the 	AV 	input, 	to 	which 	the 	TV 	device 	is 	connect
-
ed. 	Then 	the 	station 	on 	the 	TV 	set 	is 	locked 	during 	the 	timer	
recording. 	It 	is 	not 	possible 	to 	switch 	over 	to 	another 	DVB	
station.
Copy protection
Copy-protected	 programs	will	not	 be	output	 on	the	 EURO	 AV	sockets	
for	legal	reasons.
ENDINFO
Timer list                                         Mon 31.07/11:28Mon 14.09.    17:15-17:45  Das Erste     BrisantWed 16.09.    14:00-15:50  ZDF          Biathlon-WeltcupThu  22.09.    20:15-22:25  3sat         wissen spezial
----
ChangeDeleteNew recording
ENDOKINFOVia teletextVia EPGRecording wizardManual
 
						

							
-	48

PhotoViewer
You	can 	view 	photos 	in 	the 	standard 	JPEG 	format 	stored 	on 	a 	USB 	stick	
or 	a 	memory 	card 	in 	a 	card 	reader. 	You 	can 	also 	collect 	photos 	in 	a 	slide	
show.
Connecting
Plug	 a	card	 reader	 (with	a	USB	 cable)	 or		a	USB	 stick	 into	the	USB	 con-
nection	on	the	TV	set	(see	page	5).	
If,	 due	 to	the	 selected	 installation	 solution	of	the	 TV	set	 (e.g.	 for	wall	 as
-
sembly),	 the	USB	 socket	 is	difficult	 to	access,	 use	a	USB	 extension	 cable	
for	the	USB	stick	(available	from	your	dealer).	
To	mount	the	cover,	break	out	the	cable	opening	in	the	cover	flap.	
Starting the PhotoViewer
➠  No	 photos	 can	be	shown	 which	are	available	 in	progressive	 JPEG	format.
A	memory	 card	or	the	 USB	 stick	 should	 contain	 data	in	standard	 JPEG	
format	with	the	file	extension	".jpg".
PhotoViewer	 mode	starts	automatically	 when	a	memory	 card	is	inserted	
in	 the	 card	 reader,	 or	when	 a	USB	 stick	 is	inserted.	 You	see	the	first	 page	
of	the	photo	overview	(see	right	column
).
If	 a	memory	 medium	is	already	 connected,	 start	the	PhotoViewer	 as	
follows:
Call	the	
Assist+	menu.
	34	Mark PhotoViewer.	
	OK	 calls	the	photo	overview.
If	 several	 memory	 cards	are	available	 in	the	 card	 reader,	 a	selection	 menu	
Select memory medium 	opens.
	34	Select memory medium.	
	OK	calls	the	photo	overview.
Ending the PhotoViewer 
Pull	out	the	memory	card	or	USB	stick.
or	press:
END button.
or:
TV	or	RADIO 	button.
Viewing photos
➠	The	 photo	overview 	is	displayed.
634 mark	a	photo,	page	with	
P+/P–	if	necessary.
 OK	 display	as	full	picture.
		 or	P+ next	photo.
		 or	P– previous	photo.
END:  Show/hide	photo	information.
Extended	photo	information	when	Photo	info	is	set	to	
on 	in	the	PhotoViewer	menu	(page	49).
Yellow button:	Zoom	photo .	Enlargement	factors	x,	
x4,	and	x8	are	possible.Press	the	button	several	times.
The	4th	press	returns	you	to	the	original	size.
	
Select	photo	section	in	zoom	mode	with	 634
.	
Exit	the	zoom	mode	to	the	photo	overview	with	
OK 	or	
the 	STOP 	button.
	34 	Rotate	picture	by	90	degrees	to	the	left/right.
➠ Photos 	displayed 	in 	a 	slide 	show 	can 	only 	be 	rotated	
in 	the 	Pause 	mode 	for 	viewing.
  OK 
or STOP 	button:	Back	to	the	 Photo	Overview.	
Operating additional equipment
OK
ENDINFOMENUOKP+P–
Folder_1
USB 1:\picture_024.jpg                                  38 picturesView pictureMark pictureSlide showscroll ↓↑ (1/3) 
 
						

							
49	-

Calling the PhotoViewer menu 
In	the	 PhotoViewer	 menu	you	 can	make	 picture	 settings	 and	select	 the	
memory	medium.
➠ 	The	photo	overview	is	displayed.
Call	the	
PhotoViewer menu.
	
Explanations of the setting possibilities Within	the	folder	 select	a	photo	 directly	 or	go	 to	the	
beginning	or	end	of	the	folder.
W i t h 	
O p t i m u m   s i z e   t h e	p h o t o 	i s 	re d u c e d 	o r 	e n-
larged 	in 	size 	so 	that 	the 	screen 	is 	optimally 	filled.	
With 	Original resolution  each	pixel 	of 	the 	photo 	represents	
one	 pixel	 on	the	 screen.	 If	the	 photo	 resolution	 is	higher	
than	 that	of	the	 screen,	 then		portions	 of	the	 photo	 will	
be	cropped.
Set 	the 	display 	time 	per 	photo 	in 	a 	slide 	show 	to 	between	
	and	60	seconds.
The	 loading	 time	for	the	 photo	 depends	 on	the	 size,	 the	
number	 of	stored	 files	and	the	transmission	 speed	of	the	
memory	 medium.	 A	photo	 change	 may	therefore	 take	
longer	than	stated.
There	 is	a	choice	 of	four	 different	 photo	transitions	 for	
changing	 slides.	You	can	also	 have	 the	photo	 transitions	
run	in	sequence.
Display 	additional 	information 	about 	the 	picture: 	Record
-
ing	time	and	date,	resolution	and	picture	size.
Set	 picture	 adjustment,	 contrast,	colour	intensity,	 colour	
temperature,	brightness,	sharpness,	DNC.
Select memory medium  from	which	 the	photos	 are	to	be	
reproduced.	 This	menu	 item	is	only	 displayed	 if	at	 least	
two	memory	media	are	available.
Open folder
➠ 	Folders	will	only	be	displayed	if	they	were	created	
on	the	memory	card	/	USB	stick.
634 mark	a	folder	in	the	photo	overview.
 OK	 open	folder.
The	photos	in	this	folder	are	displayed.
Marking photos for slide show
Mark	the	photos	that	you	want	to	display	in	a	slide	show.
463Navigate	to	a	photo.
Blue button: 	marks	photo	for	 slide	show.
Starting a slide show
➠ No	photos	marked:	All	photos	of	the	folder	that	was	
just	opened	will	be	displayed.	➠  Photos 	marked: 	Only 	marked 	photos 	will 	be 	displayed.
Play button:  Start	/	continue 	slide	show.
	OK	 calls	the	 photo	overview.
Pause button: 	Pause	/	continue	the	slide	show.
Yellow button: 	Zoom	picture	(only	in	pause	mode).
	34	Rotate 	picture 	in 	90º 	increments 	(only 	in 	pause 	mode).
		 or	P+ next	photo.
		 or	P– previous	photo.
STOP button: 	End	slide	show.
Operating additional equipment
Go	to...
Picture 	display
Picture 	change
Picture	
crossovers
Photo 	info
Picture 	settings
Select 	memory	
medium
OK
ENDINFOMENUOKP+P–
USB 1:\Folder  _1                                      29 picturesOpen folderSlide showscroll ↓↑ (1/2) 
OK
ENDINFOMENUOKP+P–
USB 1:\Folder_1\picture_017.jpg                        29 picturesView pictureUnmark pictureSlide show (marked pictures)scroll ↓↑ (1/2) 
ENDINFO
OK
Ordner_1
Picture displayPicture crossoversPicture changeGo to ...PhotoViewer menu
Picture 001         ...        
 
						

							
-	50

Setting the remote control to other Loewe devices
The	 specified	 key	combinations	 must	be	depressed	 until	one	of	the	 LEDs	
flashes	 twice	(approximately	 5s).	The	 devices	 marked	 by	
	are	 preset	 in	
the	remote	control	included	with	the	TV	set.	
Device    
	 	 	Button combination
Loewe 	TV 	(Chassis 	L  700)	 	
	+ 		
Loewe 	Centros 	110 /117 	 	
	+ 	
Loewe 	Centros 	1 0/ 10 	HD/ 17 	HD		+ 		
Loewe 	ViewVision 	DR+	 	
	+ 		
Loewe 	ViewVision 	8106 	H	 	
	+ 		
Loewe 	Auro 	16	PS/8116 	DT	 	
	+ 		
Loewe 	Xemix 	6 	 PS	 	
	+ 		
Operating Loewe equipment
Using the remote control for a DVD player
Press	the	
DVD	button,	the	display	above	it	will	light	for	
approx.	5	seconds.
Using the remote control for a recorder
Press	the	
REC	button,	the	display	above	it	will	light	for	
approx.	5	seconds.
Using the remote control for the TV set
Press	the	
TV	button,	the	display	above	it	will	light	for	
approx.	5	seconds.
Every	 time	the	button	 is	pressed,	 the	display	 of	the	 selected	 operating	
mode	lights	up	(TV	–	REC	–	DVD	–	RADIO).
Operating additional equipment
Functions for the Loewe DVD recorder (Centros 1202, 2102 HD, ViewVision DR+)Functions for the Loewe DVD player (Auro 2216 PS, 8116 DT)
TV Sound off/on
Playback
V– / V+ TV Volume down/up
Pause /single frame
PLAY: press short:Start of current chapter/previous chapterPLAY: press long: search backPAUSE: press short: slow motion back
MENU: select/set
User interface of loaded DVDMENU: original and playlist
Show/hide menu
STOP: Call AV selection(AV1-AV4,DV,TV)ViewVision DR+:PLAY: skip 15 Sec.
Timer recording menu;timer recording list menu
Card Reader operationViewVision DR+: “Home” menu
LED indicator for currentoperating mode
Record
Switch on/off - on stand by
PLAY: Press short: next chapterPLAY: Press long: search forwardPAUSE: Press short: slow motion forward
Blue button: DISC: short: Set marker; long: Marker search
Stop
MENU: hide menu
Info; PLAY: menu bar
PIP (picture in picture)
P+/P-PLAY: Next chapter; STOP: Select station up/down
STOP: Title list; PLAY: Edit thumbnail;CARD: Photo-, Music-, Film-ModeViewVision DR+:Timeshift Mode
TV Sound menu
STOP: Select station directlyMENU: enter numbers or letters
Status display (TV, DVD)MENU: confirm the menu selection
Yellow button: ZoomRed button: new chapter markerGreen button: ShowView menu
Switch over to operate TV set
Switch over to operate RecorderSwitch over to operate DVD-Player
TV-Radio Digital
ViewVision DR+: STOP: Call AV selection
Sound off/on
Playback
V– / V+ Volume down/up
Pause; single frame; slow motion
DISC: short: beginning ofchapter/title previous chapterlong: search backRADIO: short:fine tuning back long: search back
DISC: chapter up/down;MENU: select up/downDISC: search back/forward;MENU: select left/right
DISC: User interface of loaded DVD
Show/hide menu; MENU: close window
DISC: Repeat; RADIO: displayRDS name/frequency of station
Sleep timer
DISC: Repeat A-B; RADIO: FM/AM-mode
LED indicator for current operating mode
no function
Switch on/off - on stand by
DISC: short: next chapter/title; long: search forwardRADIO: short: fine tuning forward; long: search forward
Blue button: Set marker
Stop
DISC: Status display; RADIO: station table;MENU: hide menu
DISC: menu barMENU: context help
Select external audio source
P+/P–DISC: next/previous chapter; RADIO: station forward/back
Set TV picture format; RADIO: Mono/Stereo
Select sound format
DISC: select chapter/title;RADIO: select stored station;MENU: enter digits
DISC: Title/Chapter overview; RADIO: station table;MENU: confirm menu selection
Yellow button: Zoom
Red button: DISC: camera position
Green button:Title/Chapter selection
Switch over to operate TV set
Switch over to operate RecorderSwitch over to operate Auro
short: TV Radio Digital; long: Auro FM/AM-Radio