Midway Touch Master Infinity Countertop Operation Manual
Have a look at the manual Midway Touch Master Infinity Countertop Operation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 192 Midway manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Touchmaster® Infinity Countertop Service - 3 REAR DOOR REMOVAL 1. Insert key into Rear Door. Turn key 90 degrees clockwise to unlock. 2. Remove two screws that secure Rear Door. 3. Rear Door is hinged at bottom. Swing Door on hinge, remove, and set in safe place. 4. To replace, insert bottom hinges and swing Door closed. Turn key 90 degrees counter-clockwise to lock. Reinstall Rear Door screws. REAR DOOR REMOVAL TOP COVER ASSEMBLY REMOVAL 1. Remove Rear Door. Remove three right screws from rear of Top Cover Assembly. (Screw on left is tamper proof and does not hold Top Cover Assembly.) 2. W ithout completely removing, gently pull Top Cover Assembly downward two to three inches along slope of Base Assembly. Pivot the Cover enough to expose fan wire. Disconnect fan wire. Remove Top Cover Assembly and set in a safe place. 3. To replace Cover, align on Base Assembly close enough to reattach fan cable connector. Slide Top Cover Assembly fully onto base assembly. Fasten three screws and tighten. CONNECTORCABLE FAN TOP COVER ASSEMBLY REMOVAL
Service - 4 Midway Amusement Games, LLC CONTROL SWITCH ACCESS Remove Side Cover Assembly to access TEST and CAL. pushbuttons on interior wall of cash chamber. • CAL. pushbutton lets you calibrate Touchscreen. This is crucial to maintaining quality of game play. • TEST pushbutton gives you access to system software to reset high scores, customize Attract Mode with location name, review game audits, and set other options. CAL. AND TEST BUTTONS LOCATION DEFLECTION BOARD BRACKET PIVOTING You need not remove the Deflection Board Bracket to access components. Pivot the Bracket as follows: 1. Remove Rear Door and Top Cover Assembly. 2. Remove Deflection Board Bracket screw nearest Coin Meter. 3. Loosen Bracket screws holding plate on the opposite side, but do not remove. 4. Lift Rear of bracket until spring-loaded pin near Touchscreen snaps into hole in side panel wall. To replace Bracket, push in spring-loaded pin and swivel Bracket back into position. Replace and tighten screws. REMOVE THIS SCREW LOOSEN THESE SCREWS. SPRING-LOADED PIN DEFLECTION BOARD BRACKET PIVOTING
Touchmaster® Infinity Countertop Service - 5 SERVICING THE TOUCHMASTER® INFINITY COUNTERTOP Only qualified service personnel should maintain and repair a Touchmaster® Infinity. Read all instructions and safety warnings carefully before beginning service. Failure to do so may cause serious injury or damage to machine. More specific notes, cautions, and warnings appear in manual where applicable. Each of the following service instructions requires you to switch AC power off and unplug line cord from AC power source. Do not attempt any service while AC power is on. This may damage your video game machine or cause injury, as well as void warranty. Marquee Grip both sides of marquee and pull forward and down to free magnet strips from top cover. Lift sign up and off cabinet. Slide sign out of top cover. Padlocks Your Touchmaster ® Infinity is not built with a padlock, but you can install one to deter removal of cash vault. Place cash vault in cash chamber and install a small padlock through hasp. MAGNETIC STRIP MARQUEE RETAINER WITH MARQUEE CIRCUIT BREAKER POWER SWITCH HASP CABINET REAR Power Switch Remove top cover. Press upper and lower locking tabs on one side of switch inward. Slide that side partially out through rear wall. Use flat screwdriver if needed. Press in tabs on other side and wriggle device until tabs on both sides are outside cabinet. Remove wires. Remove power switch from cabinet. Circuit Breaker To reset, push in circuit breaker button. To remove circuit breaker, remove top cover. W ith a flat screwdriver, push tab on one side of circuit breaker inward. Slide side partially out through rear wall. Press tab on other side and wiggle device until both tabs are free. Remove wires. CIRCUIT BREAKER POWER SWITCH POWER SWITCH AND CIRCUIT BREAKER
Service - 6 Midway Amusement Games, LLC Rotating Base Unlock and open Side Cover. Remove Cash Vault. Remove nylon screw from cash chamber. Replace Cash Vault and Side Cover. Turn cabinet upside down. Cut holes in pad to access nuts. Unscrew nuts and remove base. ROTATING BASE REMOVAL Fan Remove Rear Door and Top Cover Assembly. Disconnect fan wire connector. Use small pliers or nut driver to loosen and remove four nuts and fan grill from threaded studs. Remove fan from Top Cover Assembly. TOP COVER ASSEMBLY Speaker Remove Side Cover Assembly. Remove DBV and Cash Vault if necessary. Disconnect speaker wiring. Remove speaker mounting nuts. Leave washers for use with replacement. Lift speaker up and off studs. Note that replacement speaker must be magnetically shielded. VAULT SPEAKER SPEAKER REMOVAL
Touchmaster® Infinity Countertop Service - 7 Pushbutton Switches Remove Side Cover Assembly, Rear Door, Top Cover Assembly. Remove switch mounting nuts. Push switches through hole. Disconnect wiring and remove switches. Coin Meter Remove Side Cover Assembly, Rear door, Top Cover Assembly. Swing up Deflection Board Bracket. Remove meter mounting screws. Disconnect wiring and lift meter away from interior wall. COIN METER PUSHBUTTON SWITCHES HASP CASH CHAMBER CONNECTORS: Check that all cable connectors are correctly secured. Do not force connectors. They are keyed to fit in only one location. Bent pins and reversed connectors may damage your game and void warranty. You may want to check all connections when you remove your machine from its carton, as connections may have loosened in transit. ANTI-STATIC BAGS: Store electronic assemblies in an anti-static area. Keep board assemblies in anti-static bags during service, transport, or storage. STATIC ELECTRICITY: Discharge static electricity buildup in your body by touching exterior of cabinet. Do this before touching or handling electronics assemblies. Failure to do this may damage assemblies. Electronics Assemblies Remove Rear Door. Disconnect hard disk drive ribbon connector. Remove screw in rear center of tray. Grasp electronics tray by vertical lip at bottom of tray. Disconnect power cables and other wiring as you slowly slide tray out of cabinet. Remove Top Cover if needed. Security Board Assembly Remove Rear Door. Pull Abyss Security Board Assembly away from top two retaining pins with a firm, gentle tug. W hen free, pull board away from bottom pins. ELECTRONICS TRAY
Service - 8 Midway Amusement Games, LLC Modem Cable Remove Rear Door. Detach connector from modem port. Remove nut and washer from modem cable clamp. To replace, secure cable in clamp and tighten nut and washer. Insert connector into port. Tie a knot in the cable between clamp and rear door for strain relief. Replace Rear Door, guiding cable through notch at bottom of door next to left hinge. MODEM CARD Battery Remove electronics tray from cabinet. Disconnect cables and remove Dolphin I/O Board Assembly to gain access to CPU Board Assembly. Pry lithium battery from socket and discard according to replacement battery instructions. LOCATION OF BATTERY Hard Disk Drive Remove Side Cover Assembly, Rear Door and Top Cover Assembly. Pivot Deflection Board Bracket up. Disconnect cables to hard drive. Remove screws holding Mounting Brackets to interior wall of Base Assembly. Remove Hard Disk Drive from cabinet. Remove screws holding Mounting Brackets to Drive. Do not overtighten screws when replacing Mounting Brackets on Drive. HARD DISK DRIVE ASSEMBLY
Touchmaster® Infinity Countertop Service - 9 Touchscreen Controller Remove Rear Door and Top Cover Assembly. Pivot Deflection Board Bracket up for access. Disconnect Touchscreen Controller cable connector (DB9) from CPU Board Assembly. Disconnect flat, rectangular Touchscreen Connector from center of Touchscreen Controller and let it hang free in cabinet. A hook and loop fastener holds controller to bulkhead. Gently pull controller box away from bulkhead and remove from cabinet. TOUCHSCREEN CONTROLLER TOUCHSCREEN CONNECTOR CABLE CABLE REMOVAL Touchscreen Remove Rear Door and Top Cover Assembly. Pivot Deflection Board Bracket. Disconnect Touchscreen Connector Cable from Touchscreen Controller. Lower Bracket down. Remove monitor bezel. Remove tape from around Touchscreen. Carefully note orientation of Touchscreen cable and adhesive strips before separating screen from monitor. W hen reinstalling bezel, begin with top screw nearest coin slot, then remaining top screw. Reinstall bottom screws in either order. MONITOR ASSEMBLY Power Supply Remove Rear Door and Top Cover Assembly. Pivot Deflection Board Bracket up. Unplug IEC plug from receptacle. Unplug DC connector from front of power supply. Remove front and rear screws from power supply. Lift power supply up off power chassis and out of cabinet. POWER SUPPLY ASSEMBLY
Service - 10 Midway Amusement Games, LLC Monitor Controls Remove Rear Door and Top Cover Assembly. Monitor control board is just above power supply and includes adjustments for contrast, brightness, horizontal size and delay, vertical size and vertical center. HIGH VOLTAGE CONSIDERATIONS: CRTs and their power supplies can retain lethal energy charges long after power is turned off. This is especially true when defective circuits prevent normal discharge. Perform two anode discharges before working on monitors. ANODE DISCHARGE 1. Connect a well-insulated ground strap to metal chassis. 2. Pivot Deflection Board Bracket. 3. Slide free end of ground strap under CRT anode cap until you make contact with anode. 4. W ait two minutes for charge recovery. 5. Repeat steps 1 through 3 a second time. Monitor Bezel Remove Rear Door, Top Cover Assembly, and electronics tray. Remove #8 nuts from inside bottom of monitor mounting bracket. (Do not remove nut holding cable clamp.) Hold bezel in place while removing screws holding top of bezel. Lift bezel up and off cabinet. Begin reinstallation with top screw nearest coin slot, then other top screw. Reinstall bottom screws in either order. CAUTION: Monitor is very heavy. Most of its weight is toward front of cabinet. Firmly support monitor as you remove it from cabinet. Monitor Mounting Bracket Pivot Deflection Board Bracket and discharge anode twice. Replace Bracket and Remove monitor bezel. Disconnect Touchscreen Connector Cable. Unscrew #10 nuts holding Monitor Mounting Bracket to Cabinet and carefully remove. Disconnect any remaining wiring. ISOLATION TRANSFORMER: Monitor does not require isolation from AC line voltage during normal operation. However, when operating outside cabinet or servicing monitor on a test bench, isolate monitor from line voltage with isolation transformer. Monitor CAUTION: This is a difficult procedure. Only qualified service personnel should attempt to remove the monitor, neckboard, and Deflection Bracket–and only with the aid of an assistant. 1. Remove monitor bezel. 2. Pivot Deflection Board Bracket and discharge anode twice. 3. Unplug AC connector from Bracket and remove cables from cable clamp on cash chamber side of Bracket. Snip wire ties on cables leading to Bracket to allow more freedom of movement. 4. Unplug Touchscreen Connector Cable. Leave Touchscreen Controller in cabinet. 5. Remove nuts and washers from four studs at front of cabinet. 6. Unscrew remaining Deflection Board Bracket screw. Have assistant turn Bracket 90 degrees, but do not rest it on any other equipment. 7. Carefully pull monitor out front of cabinet while assistant guides Bracket out with monitor.
CHAPTER 2 456 13 System NOTICE: This manual is subject to change without notice. Midway Amusement Games, LLC reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods warrants. Installing field upgrade kits may also change the operating sequence or functions.
System - 2 Midway Amusement Games, LLC Displays game help demo Displays names of record- breaking high scores for all games. Permits language selection, if available. SYSTEM SOFTWARE Touchmaster® Infinity uses a graphical user interface for its Menu System that simplifies audits and diagnostics. The following button conventions are used at the bottom of Menu System screens. or Accepts modifications to current screen and returns to previous screen. Ignores recent modifications to current screen and returns to previous screen. Proceeds to next screen in a series. Leaves Menu System and returns to Attract Mode. Returns to previous screen. Entering the system FULL MENU SYSTEM ACCESS Open the Side Access Cover and press the TEST pushbutton. Make a Selection MIDWAY Playboy Favorites Cards Action Strategy Sexy Men Quiz 1cr 1cr 1cr 1cr Credits: 3 Champions Touch bottom left of Attract Mode screen to open Touch Key access screen. Touch category to see list of games.