Miele Cva 6202 User Manual

							Unlike standard coffee machines, this
machine has a container forcoffee
beansso that they can be freshly
ground for every cup, to benefit fully
from the flavour.
First the ground coffee is moistened
with hot water (pre-brewing), to
develop the aroma. Next, hot water is
forced at high pressurethrough the
ground coffee. The pre-brewing
process is optional.
To prevent water from remaining in the
pipes, any water left is expelled,
resulting in a little trickle after the coffee
has been dispensed. The coffee is then
ready.
The usedcoffee groundsare
automatically emptied into the waste
unit. There is no need to remove the
grounds manually after each cup.
The size of cup (max. 250 ml) can be
programmed in so that the correct
amount of coffee is dispensed. If the
cup being used has a smaller capacity
than theprogrammed cup size,
preparation can be halted at any time
by pressing one of the coffee portion
buttons.Iftwo cupsof coffee or espresso are
required at the same time, the
appropriate coffee portion button must
be pressed twice. The machine will fill
the cups in two stages with a slight
pause in between.
The machine can be programmed to
grind from 6 to 9 grammes of coffee,
depending on the type. The
programmed-inquantitywill be the
same for all sizes of cup
(small/espresso, medium coffee, large
coffee). Only the amount of water will
change.
Thefinenessto which the coffee is
ground can also be programmed in.
Thehot waterfrom the hot water spout
is at an ideal temperature for making
tea.
Thelightcan be switched on
independently of operation.
In the interests of safety, the electricity
supply is switched off as soon as the
front of the machine is opened. There is
also asystem lockto prevent children
from operating the machine.
The easy to useprogramming facility
allows, amongst other things, the
language in the display to be altered,
and the water hardness to be
programmed in.
Brief description
11 
						

							To ensure that the flavour can develop
fully and be maintained for longer the
machine has an additional function to
automatically rinse and pre-warm the
system. The same function is used to
cleanthe system and the coffee spouts
after use.
Hot water from the hot water spout can
be used topre-warm the cups.
The machine can be programmed to
switch tostandby modeso it is always
ready for operation but does not
consume unnecessary electricity. This
can be programmed to happen
between 15 minutes and 3 hours after
coffee was last dispensed.
To save time when preparing coffee for
a number of people, thepre-grind
function can be selected, so there is
always a portion of coffee ready.
Brief description
12 
						

							The machine can be programmed in easy stages for
setting to your exact requirements. The following
programming options are available:
LanguageGerman, Dutch, Portuguese, Spanish,
English, Italian, French
Rinsingon, off
Water hardness
hardness 1, hardness 2, hardness 3, hardness 4
Temperature large coffee
minimum, low, medium, high, maximum
Temperature medium coffee
minimum, low, medium, high, maximum
Temperature small/espresso coffee
minimum, low, medium, high, maximum
Pre-brewingon, off, long
Pre-grindingoff, on
Programme hot wateroff, on
Total coffeenumber of coffee portions
Descalingautomatic descaling programme
Standby timerto switch off time, selectable in
15 minute stages
A more detailed explanation of the programme
options is given in the individual sections.
Programming the machine
13 
						

							To programme the machine,
^Turn the selector to the programming position. The
machine is now in programming mode and will
respond according to the symbols shown under
the buttons.
^By pressing the-orebutton
–the required programming option in the display
can be highlighted with an asterisk. Press ENTER
to select the option.
– the settings of the various programming options
can be altered.
– a time can be entered for the Standby option.
^By pressing ENTER
– a programming option highlighted with an asterisk
can be selected.
–
an alteration to the programmed settings can be
saved.
If a setting is altered  by mistake, donot
press ENTER. Turn the selector to
position 0. The altered setting will not
be saved and the original setting will be retained.
Programming the machine
14 
						

							Choosing a language
The language for the commands in the display can
be selected before the machine is used for the first
time.
^Turn the selector anti-clockwise to the
programming position.
The machine is now in programming mode and
will respond according to the symbols shown
under the buttons.
The following will appear in the display:
Programming option Language will be
highlighted with an asterisk.
^Press ENTER to confirm this option.
The sub-menu will appear in the display as
follows:
^
Press theebutton until the required language
appears (deutsch, nederlands, portugues,
espanol, english, italiano or francais).
^
Press ENTER tosavethis setting, or
turn the selector to 0 toundo the alterations if a
mistake has been made.
This will bring you back from the sub-menu.
All commands in the display will now appear in the
selected language.
Programming the machine
15 
						

							Rinsing
To remove any coffee grounds from the system the
water piping and brew unit must be rinsed through
every day before the first drink is prepared. If
programme Rinsing is set to On rinsing will start
automatically when the machine is cold and the
selector switch is set to the On position, with or
without lighting. This will warm the brew unit up at
the same time because hot water is used for the
rinse process. An appropriate message will appear
in the display.
If a drink has just been prepared the machine will
still run an automatic rinse programme shortly
before it goes into standby mode.
To prevent water from running into the
drip tray always place an empty cup
under the coffee spouts before making
the first cup of coffee.
^Turn the selector anti-clockwise to the
programming position. The machine is now in
programming mode and will respond according to
the symbols shown under the buttons.
The following message will appear in the display:
^
Press theebutton to highlight programming
option Rinsing with an asterisk.
^
Press ENTER to confirm this option.
The sub-menu will appear in the display as
follows:
Programming the machine
16 
						

							^Press theebutton to switch rinsing on or off.
It is a good idea to set this option to On
so that the rinse process cannot be
forgotten.
^Press ENTER tosavethis setting, or
turn the selector to 0 toundo the alterations if a
mistake has been made.
This will bring you back from the sub-menu.
Setting the water hardness
For trouble-free operation of the coffee machine,
and to ensure that the descaling reminder appears
in the display at the appropriate time, it is important
to programme in the water hardness. The water
hardness indicates how much calcium is dissolved
in the water. The higher the calcium content, the
harder the water is.
The machine monitors the volume of water passing
through it in conjunction with the hardness of the
water. Less hard water can be allowed to pass
through before descaling than soft water.
The local water authority will be able to tell you the
hardness of water in your area. Alternatively, you
can measure the hardness yourself using the
enclosed test strip:
Programming the machine
17 
						

							^Dip the strip in your drinking water for
approximately a second, then shake off any
excess water.
The results will be evident after about 1 minute.
If the water is harder than 7.0 mmol/l or 700 mg/l
(40 °d), limescale will build up more rapidy than
with soft water. Descaling will need to be carried
out more regularly than stated to prevent
limescale damage to the machine.
Use programming option Water hardness to
programme in the water hardness.
There are four programmable levels:
Level
(machine)Hardness
(local water)°d
(German
scale)mmol/l Water
through-
flow in litres
Hardness 1 1 (soft) 0 - 3 0 - 1.3 approx. 320
Hardness 2 1 (soft) 4 - 7 1.3 - 2.5 approx. 160
Hardness 3 2 (medium) 7 - 14 2.5 - 3.8 approx. 80
Hardness 4 3 (hard)
4 (very hard)14 - 21
above 21above
3.8approx. 40
^
Turn the selector anti-clockwise to the
programming position.
The machine is now in programming mode and
will respond according to the symbols shown
under the buttons.
The following will appear in the display:
Press theebutton to highlight programming
option Water hardness with an asterisk.
Programming the machine
18 
						

							^Press ENTER to confirm this option.
The sub-menu will appear in the display as
follows:
^Press theebutton to set the water hardness level
(hardness 1 - hardness 4)
^Press ENTER tosavethis setting, or
turn the selector to 0 toundo the alterations if a
mistake has been made.
This will bring you back from the sub-menu.
Selecting the temperature for drinks
The machine can be set at different temperatures to
suit varying coffee drinking habits.
Five temperature levels are available for each drink
option. Maximum is the highest temperature,
minimum the lowest.
Not all types of coffee can withstand a
high temperature. Certain types are too
delicate and the froth on top would not
be so good.
^
Turn the selector anti-clockwise to the
programming position.
The machine is now in programming mode and
will respond according to the symbols shown
under the buttons.
The following will appear in the display:
Programming the machine
19 
						

							^Press theebutton to highlight programming
option Temp. L coffee for large coffee, Temp.
coffee for medium coffee or Temp. S coffee for
small/espresso coffee with an asterisk.
A different temperature can be programmed for
each drink option.
^Press ENTER to confirm this option.
Depending on the programming option selected,
the sub-menu will appear in the display as follows:
^Press theebutton to set the temperature to
minimum, low, medium, high or maximum.
^Press ENTER tosavethis setting, or
turn the selector to 0 toundo the alterations if a
mistake has been made.
This will bring you back from the sub-menu.
Programming the machine
20