Miele Da2894 Manual

							Installation Instructions 
						

							22 
						

							Disposal of packing material
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
To prevent suffocation of children,
ensure that any plastic wrappings,
bags, etc. are disposed of safely
and kept out of their reach.
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling center about the
possibility of recycling these materials.
Before discarding an old hood,
unplug it from the outlet and cut off
its power cord to prevent hazards.
Caring for the environment
23 
						

							Installation accessories
24 
						

							a3 protective shields
prevent scratches to the chimney
during installation.
bUpper retaining platesecures the
chimney extension.
cMiddle retaining platefor
additional stability of the chimney.
d2 hose clipsfor securing the
ducting.
e1 reducing collar
for use with 5 (125 mm) exhaust
ducting.
Caution: During the installation
process, please be careful of sharp
edges that can cause harm.5 large headed screws 5 x 40 mm
for securing the retaining plates and the
canopy.
(S8 wall anchors included in the
packaging are not for use in USA /
CDN.)
2 screws 5 x 60 mmfor securing the
chimney.
6 screws 3.5 x 9.5 mmfor securing the
canopy and filter housing
2 screw covers
1 leverfor dismantling the chimney and
changing the light bulbs
Installation instruction sheet
Installation accessories
25 
						

							The majority of the weight of the
installed ventilation system will be
supported by the lower retaining
plate. It must be firmly attached to
the stud framingbehindthe drywall.
If studs are not available in the
required locations, a plywood
backing (min.
½ (13 mm) thick)
spanning at least two studs mustbe
installed. Failure to adequately
support the weight as stated may
result in the ventilation system falling
off the wall, causing personal injury
and property damage.
(If plywood backing is not needed, proceed to the included installationsheet.)
To install a plywood backing
^ Determine and mark the location of
the retaining plate for the canopy as
outlined on the installation sheet.
^ Make a cutting line 3 (76 mm) above
and 3 (76 mm) below the outline of
the retaining plate. ^
Find the studs to the left and right of
the mounting location by tapping the
wall or using a stud finder.
^ Mark a vertical cutting line along the
center of each stud.
Be careful not to damage any wiring
or plumbing that may be located
behind the wall. Make sure that the
power supply to the area where this
installation is being performed has
been turned off at the breaker panel
before cutting into the wall.
^ Remove the drywall between the
cutting lines and replace it with
plywood of a matching thickness
(min.
1/2 (13 mm) thick). Tape the
joints and refinish the wall.
^ Proceed to the included installation
sheet to complete the installation.
Plywood backing
26 
						

							All electrical work should be
performed by a qualified electrician
in strict accordance with national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held responsible for
unauthorized work.
Ensure that power to the appliance
is OFF while installation or repair
work is performed.
^Verify that the voltage, load and
circuit rating information found on the
data plate (located behind the
grease filters), match the household
electrical supply before installing the
hood.
^Use only with rangehood
cord-connection kits that have been
investigated and found acceptable
for use with this model rangehood.
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or call Miele’s
Technical Service Department.
U1-800-999-1360
V1-800-565-6435
WARNING:
THIS APPLIANCE MUST BE
GROUNDEDGrounding Instructions
This appliance must be grounded. In
the event of an electrical short circuit,
grounding reduces the risk of electric
shock by providing a path of least
resistance. This appliance is equipped
with a cord having a grounding wire
with a grounding plug. The plug must
be plugged into an outlet that is
properly installed and grounded.
WARNING - Improper grounding can
result in a risk of electric shock.
If there is any doubt, have the electrical
system of the house checked by a
qualified electrician. The manufacturer
cannot be held responsible for
damages caused by the lack, or
inadequacy, of an effective grounding
system.
Do not use an extension cord. If the
power supply cord is too short, have a
qualified electrician install an outlet
near the appliance.
Important
The hood comes equipped with a 4 ft
(1.2 m) power cord with a NEMA 1-15
molded plug for connection to a
120 VAC, 60 Hz, 15 A power outlet.
Maximum load . . . . . . . . . . . . . . 390 W
Light . . . . . . . . . . . . . . . . . . . . . 4 x 10 W
Voltage . . . . . . . . . . . . . . . . . . . . . 120 V
Frequency . . . . . . . . . . . . . . . . . . 60 Hz
Circuit rating . . . . . . . . . . . . . . . . . . 15 A
Electrical data
27 
						

							Appliance dimensions
28 
						

							1) and 2)
Cut out area in wall or ceiling for
entrance of 6 (150 mm)
ductwork or 5 (125 mm) ductwork with
a reducing collar.
Do not install this exhaust hood over
cooktops burning solid fuel.
Provided a larger distance is not
given by the manufacturer of the
cooktop, follow the recommended
minimum safety distances between
a cooktop and the bottom of the
grease filter of 30 (762 mm).
If local building codes require a
greater safety distance, follow their
requirement.
Follow the safety distances
recommended by the cooktop
manufacturer in their installation and
operating instructions.
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
See IMPORTANT SAFETY
INSTRUCTIONS for further
information.Distance between cooktop and
hood (S)
^To observe the safety distance and
ensure an optimum function and use
of the hood, a distance ofS = 14
3/8"
(365 mm)between the cooktop and
the lower edge of the glass pane is
recommended.
^If the hood is fitted flush to the
ceiling, the sum of
S + H + Workspace
should not exceed the room height.
Standard unit height H
37 7/8 - 51 7/8
(960 - 1320 mm)
To fit the lower chimney section, the
distance between the top of the
chimney and the ceiling must be at
least
7/8 (20 mm).
Appliance dimensions
29 
						

							Installation instructions
^See the enclosed installation
instruction sheet.
^Please read the Important Safety
Instructions and Installation
instructions before installing this
hood.
Protective film
The casing is covered with a protective
film to prevent scratching during
transport.
^Peel off the film before installing the
casing parts.
Dismantling
If the hood needs to be disassembled,
follow the instructions on the installation
sheet in the reverse order.
A lever is enclosed for easier removal
of the chimney extension.
^After removing the screws from the
chimney, slide the lever between the
chimney and the chimney extension
and gently apply pressure to ease
the chimney from its hooks.
Installation
30