Miele Fn 14827 Operating And Installation Instructions

							^Then separate retaining plateffrom
covere, by pushing it slightly to the
left and then pulling the cover
forwards and off.
^Rotate retaining platefby 180°.
^Then fit coverefrom the front over
retaining platef, and slide it over to
the right. The writing must be visible.
^Remove coverg, rotate it by 180°
and fit it to the opposite side.
^Then fit coveretogether with
retaining platefon the opposite
side.
^
Remove caphfrom the bearing
bush in the door and refit on the
opposite side.
Changing the door hinging
51
 
						

							Changing over the hinge brackets
Important! The height of the door
on stainless steel appliances can
be adjusted.
Please read the relevant
instructions.
The instructions are the same for
all appliances from Fitting the
appliance door.
A. White appliances
(door not height adjustable)
^
Pull hinge pinatogether with discb
and adjustable footcupwards and
off.
^
Remove cover capd.
^
Undo screwseand take hinge plate
foff.
^
Unscrew partifrom hinge platef,
rotate it by 180° and refit into the hole
on the opposite side of the hinge
plate.
^
Refit cover capdin the other hole.
^
Remove coverg.
^
Unscrew and remove screwhand
refit it into the outer hole of the
opposite side.^Rotate covergby 180°, and fit it into
the holes on the other side.
^Screw hinge platefinto position on
the opposite side using the twoouter
long slots only. To make it possible to
align the door later, do not replace
thecentrescrew at this stage.
^Important. Screw the adjustable foot
cinto hinge pinaas far as it will go.
^Refit hinge pinatogether with disc
band adjustable footc. Important.
The notch at the bottom of the hinge
pin should face towards the back.
B. Stainless steel appliances
(height adjustable door)
^
Unscrew threaded pindby one turn
using the allen key supplied.
^
Pull hinge pinatogether with discb
and adjustable footcupwards and
off.
^
Remove cover cape.
^
Undo screwsfand take hinge plate
goff.
^
Refit cover capd
in the other hole.
Changing the door hinging
52
 
						

							^Unscrew partifrom hinge plateg,
rotate it by 180° and refit into the hole
on the opposite side of the hinge
plate.
^Refit cover capein the other hole.
^Unscrew threaded pindfully using
the allen key supplied.
^Fit the threaded pindinto hinge
plate on the opposite side, until it is
flush with the hinge plate.
^The end must protrude sufficiently
through the hinge pin hole such that
the guide on the hinge pin will fit over
it later on (see following illustration).
^Remove coverh.
^Unscrew and remove screwiand
refit it into the outer hole of the
opposite side.
^Rotate coverhby 180°, and fit it into
the holes on the other side.^Screw hinge plateginto position on
the opposite side using the twoouter
long slots only. To make it possible to
align the door later, do not replace
thecentrescrew at this stage.
^Important. Screw the adjustable foot
cinto hinge pinaas far as it will go.
^Refit the hinge pinatogether with
discband adjustable footcsuch
that the guide on the end of the pin
fits over the threaded pin. Then
tighten it.
^
Then tighten threaded pind.
Changing the door hinging
53
 
						

							To refit the door
^Place the door onto hinge pincfrom
above.
^Close the door.
^Fit hinge plateconto the opposite
side and secure it with screwsd.
^Fit coversaandbto their opposite
sides.
^Align the door with the appliance
housing using the outer long slots in
the lower hinge plate. Then tighten
the screws.Replacing the soft-close door
mechanism
^Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.
^
Insert the soft-close mechanism back
into the door, starting at the right
hand side.
^
Slide the soft-close mechanism back
into the door as far as it will go
towards the appliance using a
flat-headed screwdriver.
Changing the door hinging
54
 
						

							The screw holes on the left and right
must line up perfectly.
^First fix the soft-close mechanism
onto the appliance side, then onto
the handle sidec, pushing it firmly
towards the appliance.
^Attach panelbto soft-close
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom above so that
the right angle fits into the recess.
^Click coverfback into place.
Make sure that coverffits properly so
that the door can be closed without
hindrance and the pin is protected.
^
Remove retaining clipg.^Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^Close the door.
Changing the door hinging
55
 
						

							Refitting the handle
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^Loosely attach the handle to the
opposite side of the door with the two
front screwsb.
Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^
tighten both grub screwsawith a
suitable allen key until mounting plate
clines up correctly.
^
Then tighten all 4 screwsb.
^
Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
Changing the door hinging
56
 
						

							The appliance door can be aligned to
the housing using the outer long slots in
the lower hinge plate.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
^Remove centre screwafrom the
hinge plate.
^Slightly loosen both outer screwsb.
^Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be used again.
Aligning the appliance door
57
 
						

							aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installednext to a wallda
distance of approx. 55 mm must be
maintained on the hinge side between
the walldand the applianceb,so
that the doors and the handles have
sufficient space for opening.
Building in the appliance
58
 
						

							59
 
						

							Alteration rights reserved / 2811
FN 14827 S, FN 14827 S ed/csM.-Nr. 09 171 890 / 00