Miele Fn 4957 Operating And Installation Instructions

							Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliance’s energy consumption.
Location
The appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator.
Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
The climate range of the appliance is
stated on the data plate inside the
appliance.
Climate range Ambient room
temperature
SN
N
ST
T
SN-ST
SN-T+10°C to +32°C
+16°C to +32°C
+18°C to +38°C
+18°C to +43°C
+10°C to +38°C
+10°C to +43°C
The appliance will function perfectly
down to an ambient temperature of
+5 °C.
Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the air inlet and outlet must not be
covered or blocked in any way. They
should be dusted on a regular basis.
Installation
^Remove any cable clips from the
back of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position. The appliance can be
placed directly against a wall.
Aligning the appliance
^
To align the appliance adjust the feet
using the spanner supplied.
Installation
31
 
						

							To avoid a build-up of condensation
and resultant damage, refrigerators and
freezers should not normally be
installed side-by-side.
However, this appliance has side wall
heating, and can be installed
side-by-side with certain other Miele
appliances.
Your dealer will be able to advise
you on which models are suitable.
Installation
^This appliance must be installed to
the left of any refrigerator when
viewed from the front. The side wall
heating in the right-hand wall is
insulated to prevent the build-up of
condensation between the two
appliances.
^Place the two appliances as close as
possible to their final position so that
they can be aligned for any
unevenness in the floor. The back of
the appliances still needs to be kept
accessible to complete the
installation.
Joining the two appliances
together
You will need a spirit level, spanners,
a torque screwdriver and a socket
wrench.
^Before starting, peel off any
protective foil from appliance.
^Place the appliances next to one
another so that the fronts are aligned,
leaving a gap of 10 mm between
them.
^Open the appliance doors, and use a
screwdriver to lever plinth facingsa
out, then pull them forwards and off.
^
Use a screwdriver to remove covers
b.
Installing in a side-by-side combination
32
 
						

							^Align both appliances using a spirit
level.
–Align front feetcusing a spanner
d.
– Align the back feet using adjusting
deviceeand socket wrenchf.
Turn the adjusting device clockwise
to raise the appliance up at the back.
^Close the doors to check whether the
door handles are correctly aligned
with one another.
Make sure that bearing blocksg
are aligned with one another. If they
are not, the covers will not fit
properly.^Remove top screwshfrom bearing
blocksg.
^Loosely attach lower bracketiwith
screwsh.
^Push the two appliances together,
and align them again.
^Now tighten screwsh.
Do not move the appliances until all
the brackets are securely fitted.
^
Remove coversjfrom both
appliances.
^
Loosely attach large upper bracket
kusing long screwsl.
^
Push the two appliances together,
and align them again.
^
Now tighten the screwsl.
Installing in a side-by-side combination
33
 
						

							^Position wide bracketsmat the top
and bottom on the back, and push
the top bracket upwards until it is in
the correct position (z).
^Secure the brackets at the sides
using screwsn.
To avoid vibrations, neither the
brackets nor the screws should
touch the pipework on the back of
the appliances.
^Plug the two appliances into the
mains electricity supply points.
Appliances with integrated
ice-maker (depending on model):
Plumb the appliance into the mains
water supply.
^
Carefully push the two appliances
back into their final position. It is
easier if you raise the appliances at
the front, and roll them back on their
rear rollers.
The height of the appliances can be
aligned again if necessary.^Position the long stainless steel trim
olightly in the gap, making sure that
it is located above bracketi.
^Then push it carefully into the gap.
Use a soft cloth to do this to avoid
denting the trim.
^Carefully remove the protective foil
from the stainless steel trim.
^
Push short trimpinto the gap at the
top. Make sure that the gap in the
trim faces the front. The trim must sit
flush with the top of the appliances at
the front.
Installing in a side-by-side combination
34
 
						

							^Fit coverqin the space between the
control panels. Make sure that the
outer edges of the cover are flush
with the control panels. The cover
can be pulled out to adjust it to the
right size.
The gap in the cover must face
downwards to fit properly over the
stainless steel trim.
^Break off thin tagsrfrom plinth
facingsa. Important: Make sure you
remove these from the correct side -
i.e. from the handle side of the
appliances.
^
Refit plinth facings , pushing firmly
into position.
^
Refit coversb.
35
Installing in a side-by-side combination
 
						

							The appliance is supplied left hand
hinged. If right hand door hinging is
required, follow the instructions below.
Removing the door handle:
First the side section of the handle must
be removed:
^Pull door handleatowards you. Side
sectionbslides back, creating a
gapdbetween side sectionband
mounting platec.
^Place a suitable object (e.g. a spoon
handle) in gapd, and slowly lever
the handle towards the door.
Be careful not to let the spoon
handle slip, causing damage to the
appliance.
The side sectionbcan now be
removed.
^
Pull side sectionbout of the guides
on the mounting plate.
^
Loosen the 4 screws (Torx 15) in the
mounting plate, and remove the
handle.^Remove the cover caps from the
opposite side, and fit them into the
empty holes.
Changing over the door:
^Open the appliance door.
^Use a screwdriver to lever plintha
out, then pull it forwards and out.
^
Use a screwdriver to remove cover
b, then close the door.
^
Remove screwccompletely.
^
Pull door supportdtogether with
bearing boltedownwards, then tilt it
forwards and take it off.
Changing the door hinging
36
 
						

							^Open the door, tilt it downwards and
take it off.
^Remove coverf, and unscrew hinge
bracketg.
^Fit bearing bolthin the second hole
of hinge bracketg.
^Refit bracketiand coverjturned
through 180° on the opposite side.
^
Screw hinge bracketginto the
opposite side.
TheM4 screwhas to be screwed into
the left hole of the hinge bracket.
^
Turn coverfthrough 180°, and fit it
on the other side.
^
Remove spacerkwith a screwdriver
and refit it on the opposite side.
^
Remove pluglfrom the door
bearing bush in the door and refit on
the opposite side.
^
Hang the door on bearing bolthand
then close the appliance door.
In the following illustration the door
is not shown in the closed position to
make it easier to see what happens
next.
^Turn door supportbthrough 180°,
pull bearing boltaout, and then fit
both parts into bearing blockf:
To do this push bearing boltathe
other way round through bearing
blockfinto door supportb. Swing
the door support in, push upwards
and re-assemble with screwc.
Changing the door hinging
37
 
						

							^Align the door with the appliance
housing using the long slot in bearing
blockf. Then tighten screwc.
^Refit plinth facingd, pushing it firmly
into position.
^With the door open, position covere
in the front of the plinth facing, and
push it firmly into position.
Refitting the handle:
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^
Loosely attach the handle to the
opposite side of the door with the two
front screwsb.
Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^
tighten both grub screwsawith the
allen key provided until mounting
plateclines up correctly.^Then tighten all 4 fixing screwsb.
^Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
Changing the door hinging
38
 
						

							600 mm wide appliancescan be
installed into a kitchen run. To match
the height of the rest of the kitchen, the
appliance can be fitted with a suitable
top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance and top box, if fitted, for air
to circulate.
A gap of at least 40 mm is required
between the top of the appliance (or
top box) and the ceiling to ensure that
air can circulate without hindrance.
Otherwise the appliance has to work
harder, resulting in an increase in
electricity consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
doorbwill protrude in front of furniture
fronts at the sides by 34 mm and by
51 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
Wheninstalled next to a wallca
distance of approx. 36 mm is needed
on the hinge side between the wall and
the appliance, so that the door and the
handle have sufficient space for
opening.
Building in the appliance
39
 
						

							Alteration rights reserved / 4905
FN 4957 S ed-1M.-Nr. 06 785 320 / 00
en-GB