Miele Fn 9752 I Operating And Installation Instructions

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety (BS 7671 in
the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
The voltage and frequency are given on
the data plate. Please ensure that these
match the household mains supply. The
fuse rating is quoted on the plug.
Connection should be made via...

This appliance must be built in,
otherwise it could tip up.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
Important: tropical /...

The ventilation gaps must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
Before installing the appliance
^Before installation remove the cover
strip, sealing strip and other
accessories from inside the
appliance and from the external rear
wall of the appliance.
^Do not remove the spacers from the
back of the appliance. These ensure
the gap required between the back
of the appliance and the wall is
maintained.
^
Remove any cable clips from the
back of the appliance.^Remove...

Niche height [mm]
A
FN 9752 i1772 - 1788
Building-in dimensions
35
 

The door hinges are set ex-works to
enable the doors to be opened wide.
However, if the opening angle of the
door needs to be limited for any reason,
the hinges can be adjusted to
accommodate this.
For example, if the appliance door hits
an adjacent wall when opened, the
opening angle can be limited to 90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.
Adjusting the door hinges
36
 

Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Appliance door
^Open the appliance door.
^
Remove coversa,bandcwith a
screwdriver.
^
Loosen fixing screwsdat the top
and the bottom slightly.^Slide the door outwards and lift it off
e....

^Unscrew mountingband pull
soft-close mechanismcdownwards
to remove it.
^Undo ball jointdusing a spanner
and remove it.
^Stand the appliance door up, and
loosen the hinges at the front (the
hinges remain open).
^
Remove screwsa, and use the
stoppers suppliedcto plug the
empty holes.
Do notclose up the hinges. Danger
of injury.
^
Replace the hinges in their diagonally
opposite cornersb.
^
Use a powered screwdriver to secure
the hinges; screwsaare
self-tapping.To secure the soft-close mechanism
^Place the...

^Push the appliance door onto the
pre-fitted screws, and then tighten
the screws.
^Replace coversa,bandc.
^
Replace the locking pins into the top
of the hinges to prevent the doors
opening too far.
Changing the door hinging
39
 

All fitting instructions given are for a
right hand hingedappliance. If you
have converted the appliance to left
hand hinging you will need to adapt
these instructions accordingly.
To install the appliance you will need
the following:
–a cross-slotted screwdriver,
–a selection of Torx screwdrivers,
–a hexagon spanner.
Weight of the furniture door
Before fitting a furniture door, ensure
that the weight of the door does not
exceed the maximum permitted:
ApplianceMaximum weight of
furniture door in kg
FN...