Miele G 1202 Sci Operating Instructions

							Electrical connection U.K.
,All electrical work must be
carried out by a suitably qualified
and competent person, in
accordance with current local and
national safety regulations (BS 7671
in the UK).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply. Please ensure the connection
data quoted on the data plate match
the household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
For extra safety it is advisable to install
a suitable residual current device
(RCD). Contact a qualified electrician
for advice.
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).Non-rewireable plugs BS 1363
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING: THIS APPLIANCE
MUST BE EARTHED
Electrical connection
61
 
						

							The Miele waterproof anti-leak
system
Providing your dishwasher has been
installed correctly, the Miele waterproof
anti-leak system will protect you from
water damage throughout its lifetime.
Connection to the water
supply
,Water in the dishwasher must
not be used as drinking water.
–The dishwasher may be connected
to a cold or hot water supply, max.
60 °C. We would only recommend
connection to a hot water supply if it
is economical, e.g. a solar powered
supply. When connected to a hot
water supply all programme stages
which would otherwise be carried out
with cold water will be carried out
with hot water.
– The inlet hose is approx. 1.5 m long.
A 1.5 metre long flexible metal
extension hose, pressure tested to
14,000 kPa/ 140 bar, is available as
an optional accessory if required.
–
A stopcock with a
3/4 male thread
must be provided on site.
–
This appliance is constructed to
comply with IEC/EN/DIN 61770 //
VDE 0700 Section 600, and may be
connected to a suitable supply
without an extra non-return valve if
national regulations permit.–The water pressure (flow pressure at
the take-off point) must be between
30 and 1000 kPa (0.3 and 10 bar).
If the water pressure is too high, a
pressure reducer valve must be
fitted.
,To avoid any damage to the
appliance, the dishwasher must only
be connected to a fully vented
plumbing system.
!The inlet hose mustnotbe
shortened or damaged in any way
as it contains electrical components
(see illustration).
Plumbing
62
 
						

							Drainage
–The appliance drainage system is
fitted with a non-return valve, which
prevents dirty water from flowing
back into the dishwasher via the
drain hose.
–The dishwasher is supplied with
approx. 1.5 m of flexible drain hose
with an internal diameter of 22 mm.
–The drain hose can be extended
using a connection piece to attach a
further length of hose.
The drainage length must not be
longer than 4 m, and the delivery
head must not exceed 1 m.
– If the hose is to be directly fitted to
the drainage outlet on site, use the
hose clip supplied (see installation
diagram).
– The hose can be directed to the left
or the right of the appliance.
– The on-site connector for the drain
hose can be adapted to different
widths of hose. If the connector
protrudes too far into the drain hose,
it will need to be shortened.
Otherwise the drain hose may
become blocked.
–
The drain hose must not be
shortened.
,Make sure that there are no
kinks in the hose, and that it is not
squashed or stretched.Venting the drainage system
If the on-site drain connection is
situated lower than the guide path for
the bottom basket rollers in the open
door, the drainage system must be
vented. Otherwise a siphoning effect
during a programme can cause the
appliance to empty itself of water.
To vent it:
^Open the dishwasher door fully.
^
Pull the lower spray arm firmly
upwards to remove it.
^
Cut off the top of the vent valve in the
wash cabinet.
Plumbing
63
 
						

							Height freestanding 84.5 cm
(adjustable +3.5 cm)
Height built-in 80.5 cm
(adjustable + 6.5 cm)
Height of building-in recess Min. 80.5 cm (+ 6.5 cm)
Width 44.8 cm
Width of building-in
recess45 cm
Depth:
Freestanding
Built-in60 cm
57 cm
Weight Max. 50 kg
Voltage 230 V
Connected load 2200 W
Fuse rating 10 A
Test certificates awarded KEMA, VDE, radio and television suppressed
Water pressure (flow rate) 30 - 1000 kPa
(0.3 - 10 bar)
Hot water connection Up to max. 60 °C
Delivery head Max. 1 m
Drainage length Max. 4 m
Mains cable Approx. 1.7 m
Capacity 9 place settings
Technical data
64
 
						

							65
 
						

							66
 
						

							67
 
						

							Alteration rights reserved/
G1202 / 0509M.-Nr. 07 502 130 / 00