Miele G 2732 Operating Instructions

							Installation, repairs and other
work by unqualified persons could
be dangerous. The manufacturer
cannot be held responsible for
unauthorized work.
Check that the voltage, frequency
and fuse rating shown on the data
plate match the household mains
supply.
The power outlet must be accessible
after installation. Do not use an
extension cord to connect the
dishwasher to the mains. Danger of
overheating! See data plate on the
right side of the door.
A damaged power cord must only
be replaced with a genuine Miele
cord by a Miele service technician.
GROUNDING INSTRUCTIONS
THIS APPLIANCE MUST BE
GROUNDED.
In the event of a malfunction or
breakdown, grounding will reduce the
risk of electric shock by providing a
path of least resistance for the electrical
current. This appliance is equipped
with a cord having an equipment
grounding conductor and a grounding
plug. The plug must be plugged into an
appropriate outlet that is installed and
grounded in accordance with all local
codes and ordinances.
Improper connection of the
equipment grounding conductor
can result in electric shock. Do
not modify the plug provided with
the appliance; if it will not fit the
outlet, have a proper outlet
installed by a qualified electrician.
If there is any question
concerning the proper electrical
connection or grounding of this
appliance to the power supply,
please consult a licensed
electrician or call Miele’s
Technical Service Department:
1-800-999-1360
1-800-565-6435
Specifications
The dishwasher comes equipped with a
4 ft (1.2 m) power cord with a molded
plug for connection to 120 V, 60 Hz,
15 A grounded receptacle.
Electrical connection
71
 
						

							Waterproof system
All Miele dishwashers have a safety valve
located on the incoming water line and a
sealed underside with a water sensor.
If a fault occurs, the water intake is
stopped and the drain pump is activated.
Water damage, if any, is minimized.
Providing the dishwasher was installed
correctly by a Miele technician, the
waterproof system will protect you from
water damage throughout the lifetime of
the machine.
Connection to the water supply
Do not drink water from the
dishwasher!
– The dishwasher can heat its own water
to the temperature required by the
wash program. This allows for
connection of the machine to either a
hot or cold water source. For lowest
energy consumption connect the
dishwasher to a cold water source. For
fastest possible wash times, with
slightly higher energy consumption,
connect the dishwasher to a hot water
source. All programs use hot water in
the rinse cycles.
–
To use the Energy Saver program, a
hot water connection of minimum
115°F / 45°C and maximum 140°F /
60°C (water intake temperature) is
necessary.
The higher the water intake
temperature, the better the cleaning
and drying results.–The inlet hose is approximately 5 ft.
(1.5m) long. A 5 ft. (1.5m) extension
hose is available from Miele.
–The water inlet hose comes equipped
with a 3/4 female hose thread
connector. This can be directly
connected to a water supply with 3/4
MHT (male hose thread ends).
–Water pressure: Must be between 4.5 -
145 psi (0.3 - 10 bar).
If the water pressure is lower, the
display shows Water intake
see Frequently asked questions.
With high water intake pressure, a
reducing valve must be used.To prevent damage to the
dishwasher, it must only be
connected to a fully vented drainage
system.
Do not cut the intake hose. It contains
electrical wiring. If the hose is cut, the
dishwasher will not work. There will be
a water leak and you could be injured.
If the hose is too long, coil it neatly
and place it behind the machine.
Plumbing
72
 
						

							Drainage
–The machine comes equipped with a
built-in non-return valve on the
discharge side to prevent waste
water from flowing back into the
dishwasher.
–The dishwasher is equipped with a
5 ft (1.5 m) flexible drain hose with an
internal diameter of 7/8 (22 mm).
–Drain hose extensions and adapters
can be ordered from Miele.
The maximum drain hose length is
13 ft. (4 m), max. drain height: 39
(1 m).
– If the hose is to be directly fitted to
the drainage outlet on site, use the
supplied hose clip (see assembly
plan).
– The hose can be installed to the left
or right side.
– The existing drain pipe for the drain
hose is designed for various hose
diameters. The drain pipe must be
shortened if the drain pipe extends
too far into the drain hose. The drain
hose could get clogged.
–
The drain hose must not be
shortened.
Make sure the hose is installed
without kinking, pressure or being
pulled.Venting the drainage system
If the dishwasher drain hose is
connected to a floor drain or to a drain
pipe that is less than 8 (20 cm) above
the floor, the drain must be vented.
Otherwise the water inside the
dishwasher may siphon out during the
wash program.
Open the dishwasher door and
remove the lower basket.
Pull the lower spray arm firmly
upwards to remove.

Cut off the vent cap located at the
right rear of the triple filter system, as
illustrated.
Plumbing
73
 
						

							The Miele RemoteVision system is
designed to send messages directly to
Miele and/or your PC.
For information on set-up and
installation of the RemoteVision module
see the Installation section of this
manual.Be sure your wireless system meets the
following requirements
–Windows XP
®or newer operating
system, Mac®OS X 10.3 or higher
–Cable or DSL modem
–Microsoft
®Internet Explorer 6 or
higher, Safari 2.0 or higher, Firefox
1.5 or higher
* Please note that each wireless router
manufacturer supplies their own device
drivers and setup programs. Due to the
differences in manufacturers, exact
router setup instructions are not
included in this manual. Wording and
instructions may vary.
RemoteVision
74
 
						

							75
 
						

							Alterations reserved/4308
G 2732
For the most updated manual see the Miele web site.M.-Nr. 07 329 090 / 02