Miele G 7883 User Manual

3. Setting the buzzer
A buzzer can be set to signal the
following:
–End of program = continuous buzzer
–Error = rhythmic buzz
–Timer to allow sampling of the last
final rinse water
= intervals of 3 short buzzes and
2 seconds break
^Turn the program selector to STOP
f.
^Turn the machine off.
^Press and hold Displayßand
Start6.At the same time,turn the
lab washer on with the On/Off
button.
The displays shows the current
program status P....
The Fill/Drain indicator lights.
^Press Drying04 times. E04...

4. Restoring the factory
settings
^Turn the program selector to STOP
f.
^Turn the machine off.
^Press and hold Displayßand
Start6.At the same time,turn the
lab washer on with the On/Off
button.
The displays shows the current
program status P....
The Fill/Drain indicator lights.
^Press and hold Drying0until E33
appears in the display.
^Turn the program selector to any
position (except STOP).
The display shows either 00 or PP.
00 = factory setting; electronic was
not reprogrammed.
PP = electronic was...

Filter combination
,The machine must not be used
without all the filters in place. The
filters protect the circulation pump
from damage caused by foreign
objects.
The filter combination in the base of
the wash cabinet should be
inspected regularly and cleaned if
necessary.
Caution:
Watch out for sharp objects which
could cause injury.
Cleaning the coarse filter
^
Press the two tabs together. Remove
and clean the coarse filter.
^
Put the clean filter back in position
and press until it clicks in...

Cleaning the non-return valve
and drain pump
If water has not been pumped away at
the end of a program, the drain pump
or the non-return valve may be blocked.
^Turn off the washer.
^Remove the filter combination from
the wash cabinet.
^Tilt the locking clamp to the side.
^
Pull out the non-return valve and
rinse under running water.The drain pump is located beneath the
non-return valve (see arrow).
^Before returning the non-return valve,
check that the drain pump is not
blocked. Spin the propeller...

Cleaning the filters in the water
inlet
Filters are incorporated in the screw
connection of the water inlet hose to
protect the water inlet valve. If these
filters become dirty, they need to be
cleaned, otherwise insufficient water
flows into the wash cabinet.
,The plastic housing of the water
connection contains an electrical
component. It must not be
submerged in water.
To clean the filters
^Disconnect the machine from the
main electrical supply.
^Turn off the water supply.
^Unscrew the water inlet...

With the aid of the following guide, minor problems can be fixed without a service
call.
The Miele control unit includes a wide range of fault codes to indicate specific
errors. These fault codes are indicated on the display by a flashing F. . .  (Ranging
from F1 up to F30.) If one of these codes appears, please contact the Miele
Technical Service Department at 1-800-991-9380 for assistance.
What if … Possible fault Fix
the machine does not
start?The door is not
properly closed.Close the door firmly.
The...

What if … Possible fault Fix
the wash cycle finishes
too early, the "Fill/Drain"
indicator flashes and
the fault code "F A"
appears in the display?–The drain hose is
kinked.
–The drain pump is
blocked.–Turn the program selector to
Stopf(the fault code
goes out).
–Press the On/Off button to
turn the machine off.
–Remove any kinks in the
hose. Clean the drain pump
(see Machine care).
–Turn the machine on, run the
drain program then restart
the original program (see
Operation).
water in the...

What if … Possible fault Fix
I need to open the door
during a power failure?–see Opening and
closing the door.
the fault was caused by
a possible misfunction.–Turn the program
selector to Stopf
(the fault code goes
out).
–Press the On/Off
button to turn the
machine off.
–Turn the machine on
again and reselect the
program.
If there are further
difficulties, or if the fault
code "F..." appears in
the display, please
contact the Miele
Service Department. See
back cover for phone
numbers.
Trouble...

In the event of a fault which you cannot
correct yourself please contact the
Miele Technical Service Department
U1-800-991-9380
[email protected]
l1-800-565-6435
[email protected]
Please quote the model of your
machine. This information can be found
on the machine’s front panel.
After Sales Service
49 

50