Miele G 7893 Manual

							Drainage
–The drainage system is fitted with a
non-return valve which prevents dirty
water from flowing back into the
machine via the drain hose.
–The machine should preferably be
connected to aseparatedrainage
system on-site.
If separate drainage is not available,
contact your Miele application
specialist for professional advice.
The on-site drain connection point
should be sited between 0.3 m and
1mabove the lower edge of the
machine.
If it is lower than 0.3 m, lay the hose
in a curve at a height of at least
0.3 m.
The drainage system must be able to
take a minimum drainage flow of
16 l/min.
– The drain hose is approx. 1.4 m long,
is flexible and has an internal
diameter of 22 mm. It must not be
shortened.
Hose clips are supplied for securing
it in position.
–
A longer drain hose (up to 4 m long)
is available to order from the Miele
Spare Parts Dept.
–
The drainage system must not
exceed 4 metres.
See also the installation diagram
supplied.
Plumbing
71 
						

							Programme When to use
AFreely programmable programme (programmed by a Miele authorised service
technician).
B
INORGANICFor the removal of inorganic residues;
general analysis and water analysis, suitable for low to medium soiling levels and
for medium to high quality rinse requirements.
C
ORGANICFor the removal of organic residues such as oil, grease, wax and agar. Suitable
for preparation and analytical applications with medium to high levels of soiling
and medium quality rinse requirements. Requiresliquid cleaning agent:Hot,
cold and AD water connections recommended.
D
STANDARDSuitable for a variety of soil types which do not denaturate or break down into
alkalis. Suitable for preparation and analytical applications with low levels of
soiling and rinse requirements.
E
UNIVERSALFor the removal of organic residues such as protein, oil, certain types of grease,
and for certain inorganic residues (pH 7 water soluble metal salts). Suitable for
preparation and analytical applications with low to medium levels of soiling and
medium quality rinse requirements.
F
INTENSIVEFor the removal of organic residues such as protein, oil, cell and tissue culture,
oils and certain types of grease (pH 7 water soluble metal salts). Suitable for
preparation and analytical applications with medium to high levels of soiling and
medium to high quality rinse requirements.
G
PLASTICFor temperature sensitive laboratory equipment e.g. plastic bottles (temperature
resistant to at least 55ºC). Suitable for preparation and analytical applications
with low to medium levels of soiling and medium quality rinse requirements.
6
DRAINTo drain soiled water from the machine, e.g. after a programme has been
cancelled.If applicable, observe regulations on containing the spread of
epidemics- see "To cancel a programme".
D
PRE-RINSEFor rinsing heavily soiled items (e.g. for removing soiling or disinfectant residue,
or to prevent soiling drying on to dishes when a complete programme does not
yet need to be run).
varioTDComplies with general hygiene regulations. 90°C (+ 5 °C, - 0 °C) programme with
a 5-minute holding time, in accordance with the requirements of EN ISO 15883-1.
SPECIAL
93°C-10’For cleaning and thermal disinfection at 93°C with a 10 minute holding time, area
of effectiveness A/B range, in accordance with § 18 IfSG.
CW = Cold water, HW = Hot water, AD = Aqua destillata, °C = Temperature, + min = Holding time
* The dispensing of rinsing agent with DOS 2 must be activated by a Miele service technician
Programme chart
72 
						

							Programme sequence
Pre-wash
12Main wash
12Rinse
12Rinse
34Final rinses*
12Dryingx
12
CW HW
DOS 1
80°C
3 minHW
DOS 3HW AD AD
75°C
1 min99°C 70°C
25 min 5 min
CW
DOS 3
50°C
1 minHW
DOS 1
75°C
3 minHW
DOS 3AD AD AD
70°C
1 min99°C 70°C
25 min 5 min
HW HW
DOS 1 DOS 1
65°C 85°C
3 min 3 minHW
DOS 3HW AD AD
80°C
1 min99°C 70°C
25 min 5 min
HW
DOS 1
75°C
3 minHW
DOS 3AD AD
75°C
1 min99°C 70°C
25 min 5 min
CW HW
DOS 1
80°C
3 minHW
DOS 3HW AD AD
75°C
1 min99°C 70°C
25 min 5 min
CW HW
DOS 1
85°C
3 minHW
DOS 3AD AD AD
80°C
1 min99°C 70°C
25 min 5 min
CW CW
DOS 1
55°C
5 minCW
DOS 3CW AD AD
55°C
1 min65°C 55°C
5 min 35 min
65°C
30 min
CW
CW CW
DOS 1
55°C
5 minHW
DOS 3HW AD
93°C
5 min99°C
35 min
CW
DOS 1
93°C
10 minHW
DOS 3HW AD
75°C
3 min99°C
35 min
x = Additional function, DOS 1 = For liquid cleaning agent from 40 °C
DOS 3 = For dispensing neutralising agent after water has been taken in
Programme chart
73 
						

							Height with lid
Height without lid85 cm
82 cm
Width 60 cm
Depth
Depth with door open60 cm
120 cm
Weight (net) 70 kg
Voltage, connected load, fuse rating See data plate
Mains cable Approx. 1.8 m
Water temperature:
Cold water
Hot and AD waterMax. 20 °C
max. 70 °C
Static water pressure Max. 1000 kPa (10 bar) pressure
Minimum flow pressure:
Cold/hot water inlet connections
AD water connection100 kPa pressure
60 kPa pressure
Recommended flow pressure:
Cold/hot water inlet connections
AD water connection0250 kPa pressure
0150 kPa pressure
Delivery head min. 0.3 m, max. 1 m
Ambient temperature 5 °C to 40 °C
Relative humidity
Decreasing proportionately to80 % for temperatures to 31 °C
50 % for temperatures to 40 °C
Altitude Max. 1500 m#
Degree of soiling P2 (according to IEC/EN 61010-1)
Protection category (according to IEC
60529)IP20 (Dust permeation)
Noise level in dB (A),
Sound level LpA during cleaning and
drying phases
						

							75 
						

							Alteration rights reserved / 3607M.-Nr. 07 125 650 / 00