Miele H 5241 B Manual

							Gourmet oven dish
The gourmet oven dish can be placed
in the oven directly on the runners. It
has non-tip safety notches like the
universal tray to prevent it being pulled
out too far.
It has an anti-stick coating.
It is available in two sizes:
–HUB 5000-M (internal dimensions:
approx. 38 x 22x8cm)
– HUB 5000-XL (internal dimensions:
approx. 38 x 35x8cm)
Gourmet oven dish lid
When ordering a lid, please specify the
gourmet oven dish it is to be used with
(HUB 5000 M or XL).Catalytic liners
Replacement side and roof liners are
available to order if required. Please
quote the model number of your oven
when placing your order.
Miele E-cloth
Removes grease and stains and leaves
no smearing. Suitable for cleaning
surfaces such as stainless steel, glass,
plastic and chrome without the use of
chemicals.
Miele oven cleaner
Suitable for removing stubborn soiling.
It is not necessary to pre-heat the oven
beforehand.
Optional accessories
71 
						

							All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations (BS
7671 in the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
unauthorised work.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Thevoltage and connected loadare
given on the data plate, visible below
the oven interior, with the door open.
Ensure that these match the household
mains supply. Please quote these data,
and the model and serial number when
contacting Miele.
Connection of this appliance should be
made via a fused connection unit or a
suitable isolator, which complies with
national and local safety regulations,
and the on/off switch should be easily
accessible after the appliance has
been built in.
If the switch is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a residual current
device (RCD). Please contact a
qualified electrician for advice.
When switched off there must be an
all-pole contact gap of 3 mm in theisolator switch (including switch, fuses
and relays acc. to EN 60 335).
Important U.K.
The appliance is supplied for
connection to a 230-240 V, 50 Hz
supply with a 3-core cable.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue = neutral
Brown = live
WARNING
THIS APPLIANCE MUST BE
EARTHED
When replacing the cable supplied
with another cable or changing the
connection, only cable type
H 05 VV-F or H 05 RR-F with a
suitable cross-sectional area (CSA)
may be used (available from the
Miele Customer Contact Centre).
Electrical connection
72 
						

							Dimensions are given in "mm".
Appliance and niche dimensions
Installation in a base unit
Installation in a tall unit
* Appliances with glass front
** Appliances with metal front
Building-in diagrams
73 
						

							Front dimensions
AH 5141: 53.2
H 5241: 47.5
BAppliances with glass front: 2.2
Appliances with metal front: 1.2
Building-in diagrams
74 
						

							The appliance must not be
operated until it has been correctly
installed in its housing unit.
Otherwise it poses an electric shock
hazard.
To ensure adequate ventilation to
the oven once installed:
– do not fit a rear panel into the
housing unit.
– make sure that the shelf on
which the appliance is placed
does not touch the wall.
– do not fit insulation material
inside the housing unit.
When installing the appliance do not
lift it up by the door handle as this
can damage the door.
Turn off the mains electricity
supply to the isolator.
Connect the mains cable from the
oven to the isolator.
It is a good idea to remove the door
before installing the appliance. The
oven will then be lighter to lift when you
are positioning it the housing unit and
also it will not be possible to use the
handle to lift it by mistake.
Push the appliance back into the
housing unit and align it.
Open the door (if you have not
removed it previously).

Use the screws supplied to secure
the appliance to the side walls of the
housing unit through the holes in the
oven trim.

Replace the door (if you removed it
before installing the appliance). See
"Cleaning and care - To refit the
door").
Installing the oven
75 
						

							Alteration rights reserved / 22 / 2611
(H 5141 BP; H 5241 BP)M.-Nr. 07 961 200 / 02